Accueil
Catégories
> Essais dynamiques
Essais dynamiquesVoir aussi
|
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Anomalies of pigskin structure / R. Monastyrska-Przybylak in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 66 (Année 1982)
[article]
Titre : Anomalies of pigskin structure : Part I. Differences in basic strength properties Type de document : texte imprimé Auteurs : R. Monastyrska-Przybylak, Auteur Année de publication : 1982 Article en page(s) : p. 61-65 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Allongement à la rupture
Cuirs et peaux -- Défauts
Cuirs et peaux -- Propriétés mécaniques
Cuirs et peaux de porcs
Essais dynamiques
Résistance à la tractionIndex. décimale : 675 Technologie du cuir et de la fourrure Résumé : The pattern of specific distribution of strength properties is presented on a basis of detailed testing of physical properties conducted on over 100 pigskins from the three breeds. The frequent occurrence of significant differences in strength properties was found in neighbouring sites within all topographic areas of pigskins. Note de contenu : - Fig. 1 : Distribution of thickness ranges
- Fig. 2 : Distribution of loading ranges at break
- Fig. 3 : Distribution of maximum elongation ranges
- Table 1 : The list of test results of tensile strength and elongation at break significantly differing between each other, obtained from all pigskin areas of the "flagging ears" breed, from specimens cut out side by side
- Table 2 : The list of test results of tensile strength and elongation at break significantly differing between each other, obtained from all pigskin areas of the Pulawy's breed from specimens cut out side by side
- Table 3 : The list of test results of tensile strength and elongation at break significantly differing between each other, obtained from all pigskin areas of the English breed from specimens cut out side by sideEn ligne : https://drive.google.com/file/d/1g3o4XSYt0kejTa7M8NRGzXD-S8xWeKWh/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=34211
in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC) > Vol. 66 (Année 1982) . - p. 61-65[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 007129 - Périodique Bibliothèque principale Documentaires Disponible Anomalies of pigskin structure / R. Monastyrska-Przybylak in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 66 (Année 1982)
[article]
Titre : Anomalies of pigskin structure : Part III. Analysis of leather structure through fatigue and density tests Type de document : texte imprimé Auteurs : R. Monastyrska-Przybylak, Auteur Année de publication : 1982 Article en page(s) : p. 74-78 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Cuir -- Structure
Cuirs et peaux -- Analyse
Cuirs et peaux -- Défauts
Cuirs et peaux de porcs
Densité cutanée
Essais de résilience
Essais dynamiques
Matériaux -- FatigueIndex. décimale : 675 Technologie du cuir et de la fourrure Résumé : In this part of the paper we try to define the influence of leather compactness in four topographic areas tested in an electron scanning microscope, namely, neck, croupon, butt and belly, on a behaviour of pigskin leather under wear conditions. Fatigue tests in the range 0-20 % extensions and apparent density tests were performed. Total compactness of the structure was defined for tested topographic areas by means of loosening ability. It was found that the butt, commonly considered to be the most compact region of pigskin, shows the highest ability to loosening (apart from belly parts) under wear conditions. Lesser ability to loosening shows neck area and the least, croupon area. The results of apparent density tests confirmed the compactness of structure defined by fatigue tests in several topographic locations. Note de contenu : - Table 1 : Elasticity modulus values at 20 % extension before and after fatigue tests for fatliquored and non-fatliquored pigskin leathers
- Table 2 : Student's "t" values for differences before and after fatigue (critical values with 5 % error risk in parentheses), fatliquored leathers
- Table 3 : The area of field under hysteresis loop before and after fatigue tests
- Table 4 : Apparent Mass in g/cm3En ligne : https://drive.google.com/file/d/1EmIPBtjvEeZengkEvU8rwXSR79Rp9iZe/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=34213
in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC) > Vol. 66 (Année 1982) . - p. 74-78[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 007129 - Périodique Bibliothèque principale Documentaires Disponible Anticorrosion des structures en acier par systèmes de peinture - Evaluation et critères d'acceptation de l'adhésion/cohésion (résistance à la rupture) d'un revêtement - Partie 1 : Essai de traction - Norme internationale ISO 16276-1 / International Organization for Standardization (Genève, Suisse) / Geneve [Switzerland] : International Organization for Standardization (ISO) (2007)
Titre : Anticorrosion des structures en acier par systèmes de peinture - Evaluation et critères d'acceptation de l'adhésion/cohésion (résistance à la rupture) d'un revêtement - Partie 1 : Essai de traction - Norme internationale ISO 16276-1 Type de document : texte imprimé Auteurs : International Organization for Standardization (Genève, Suisse) , Auteur Editeur : Geneve [Switzerland] : International Organization for Standardization (ISO) Année de publication : 2007 Importance : V-9 p. Présentation : ill. Format : 30 cm Note générale : Bibliogr. Langues : Français (fre) Catégories : Acier L'acier est un alliage métallique utilisé dans les domaines de la construction métallique et de la construction mécanique.
L'acier est constitué d'au moins deux éléments, le fer, très majoritaire, et le carbone, dans des proportions comprises entre 0,02 % et 2 % en masse1.
C'est essentiellement la teneur en carbone qui confère à l'alliage les propriétés du métal qu'on appelle "acier". Il existe d’autres métaux à base de fer qui ne sont pas des aciers comme les fontes et les ferronickels par exemple.
Anticorrosifs -- Normes
Essais dynamiques
Métaux -- Revêtements protecteurs
Résistance à la rupture
Revêtements -- Normes:Peinture -- Normes
Revêtements protecteurs -- Normes
Traction (mécanique)Index. décimale : 667.9 Revêtements et enduits Résumé : La présente partie de l'ISO 16276 spécifie des modes opératoires permettant d'évaluer la résistance à la rupture d'un système de peinture, quelle que soit son épaisseur, appliqué sur un subjectile en acier ayant une épaisseur au moins égale à 10 mm : Les modes opératoires figurant dans la présente partie de l'ISO 16276 reposent sur des méthodes d'essai utilisant différents types de machines d'essai de traction. Les résultats obtenus sur ces différents types d'appareils d'essai ne sont pas comparables.
NOTE 1 : Si l'épaisseur du subjectile à soumettre à l'essai est inférieure à 10 mm, le subjectile peut être essayé après avoir été renforcé, soit par la technique dite "sandwich" (voir l'ISO 4624), soit par un profilé particulier (profil, en l, raidisseur arrière par exemple). Dans le cas contraire, on peut soit utiliser des panneaux d'essai ayant une épaisseur d'au moins 10 mm revêtus de la même façon que la structure, soit utiliser l'IS0 16276-2.
La présente partie de l'ISO 16276 n'est applicable que si une valeur de résistance à la rupture est spécifiée avec le type d'appareillage et le fabricant de cet appareillage. Généralement cette information figure dans la documentation contractuelle.
NOTE 2 : Une valeur de résistance à la rupture n'est significative que si les exigences relatives aux conditions ambiantes (voir 6.4.2) sont respectées.
La présente partie de l'IS0 16276 spécifie l'utilisation d'appareillages appropriés et définit les aires de contrôle, les plans d'échantillonnage et les critères d'acceptation/de rejet.
La présente partie de l'ISO 16276 ne donne aucune valeur de résistance à la rupture pour les différents systèmes de peinture.Classification ICS : 87.020 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=30131 Est accompagné de
- Anticorrosion des structures en acier par systèmes de peinture - Evaluation et critères d'acceptation de l'adhésion/cohésion (résistance à la rupture) d'un revêtement - Partie 2 : Essai de quadrillage et essai à la croix de Saint-André - Norme internationale ISO 16276-2 / International Organization for Standardization (Genève, Suisse) / Geneve [Switzerland] : International Organization for Standardization (ISO) (2007)
Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19657 ISO 16276-1 Norme Bibliothèque principale Documentaires Disponible AP-PLY : A new fibre placement architecture for fabric replacement / Martin Nagelsmit in SAMPE JOURNAL, Vol. 47, N° 2 (03-04/2011)
[article]
Titre : AP-PLY : A new fibre placement architecture for fabric replacement Type de document : texte imprimé Auteurs : Martin Nagelsmit, Auteur ; C. Kassapoglou, Auteur ; Z. Gürdal, Auteur Année de publication : 2011 Article en page(s) : p. 36-43 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Composites à fibres
Composites à fibres -- Détérioration
Composites thermoplastiques
Délaminage
Essais accélérés (technologie)
Essais de résilience
Essais dynamiques
Indentation des matériaux
Résistance des matériaux
Stratifiés
Thermodurcissables
TissésIndex. décimale : 668.4 Plastiques, vinyles Résumé : Composite laminates made with woven fabric are known to have damage resistance characteristics than unidirectional laminates. Due to the recent development in fibre placement and tape laying machines, laminates with unidirectional plies are favoured because of the automated production process. AP-PLY combines the advantages of fabrics and unidirectional layers in an automated production process. AP-PLY is a laminate configuration obtained by placing the fibre tows in special patterns that mimic the construction of w woven layer. Any material system can be used for the construction, including glass fibre, carbon fibre, thermoset and thermoplastic resins and even dry fibre placement. No adaptations to current fibre placement machines are necessary. Tests show smaller delaminations and higher residual strength for every tested. Possible applications include any number of the plies of wing and fuselage laminates or sandwich panel facesheets. It is also possible that entire laminate structures where the design is driven by damage tolerance can be constructed by AP-PLY. In addition, the prospect of eliminating or minimizing the use of fabric plies, which is a labour intensive process and replacing them with equivalent AP-PLY configurations, makes the present concept attractive for other applications where impact damagemay not be the driver. Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=12726
in SAMPE JOURNAL > Vol. 47, N° 2 (03-04/2011) . - p. 36-43[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 012893 - Périodique Bibliothèque principale Documentaires Disponible Appareils d'essai du caoutchouc et des plastiques. Types pour traction, flexion et compression (vitesse de translation constante) - Norme NF ISO 5893 / Association Française de Normalisation (Paris) / Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) (1988)
Titre de série : Appareils d'essai du caoutchouc et des plastiques Titre : Types pour traction, flexion et compression (vitesse de translation constante) - Norme NF ISO 5893 Type de document : texte imprimé Auteurs : Association Française de Normalisation (Paris) , Auteur Editeur : Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) Année de publication : 1988 Importance : 6 p. Présentation : ill. Format : 30 cm Langues : Français (fre) Catégories : Caoutchouc -- Normes
Contraintes (mécanique)
Essais dynamiques
Essais dynamiques -- Appareils et matériels
Essais dynamiques -- Normes
Flexion (mécanique)
Matières plastiques -- Normes
Traction (mécanique)Index. décimale : 678.2 Caoutchouc Résumé : La présente norme décrit les caractéristiques des machines de traction, flexion et compression (à vitesse de translation constante), utilisées pour l'essai des caoutchoucs, plastiques et adhésifs. Classification ICS : T 46-200 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=17614 Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 14719 T 46-200 Norme Bibliothèque principale Documentaires Disponible Application of some plant extracts as biocolorants for leather during finishing process / Roza Mirzamuratova in JOURNAL OF THE AMERICAN LEATHER CHEMISTS ASSOCIATION (JALCA), Vol. CXIX, N° 1 (01/2024)
PermalinkApplication of texture profile analysis (TPA) to evaluate the sensory properties of leather / Piotr Zapletal in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 100, N° 3 (05-06/2016)
PermalinkApplication of the experimental results to the modified Halpin-Tsai micromechanical model to evaluate the clay dispersion in clay-reinforced polyethylene nanocomposites / N. Uyanik in INTERNATIONAL POLYMER PROCESSING, Vol. XXIX, N° 1 (03/2014)
PermalinkApplications de la mesure de champs à la caractérisation uniaxiale ou multiaxiale des matériaux polymères / L. Chevalier in RHEOLOGIE, Vol. 6 (10/2004)
PermalinkApport de la modélisation à la compréhension du comportement mécanique des composites à matrice polymère / Roger Gaertner in ACTUALITES G.F.P., N° 91 (03/2002)
PermalinkApproche probabiliste multiéchelle pour composites renforcés fibres de carbone/époxy / Baramee Patamaprohm in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 25, N° 3-4 (2e semestre 2015)
PermalinkAramide premier choix ou régénéré : coût et risque / Serge Bourbigot in TEXTILES A USAGES TECHNIQUES (TUT), N° 44 (2e trimestre 2002)
PermalinkArkema 3 Mini 6.50 : a model of innovation / Roucayrol, Lalou in JEC COMPOSITES MAGAZINE, N° 115 (08-09/2017)
PermalinkAs far as my soles will carry me / Karoline Brückner in KUNSTSTOFFE INTERNATIONAL, Vol. 100, N° 9 (09/2010)
PermalinkAutocicatrisant d'un ionomère pour des vitesses de projectile allant du domaine quasi statique à l'impact à très haute vitesse / Thomas Haase in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 22, N° 1 (01-02-03-04/2012)
PermalinkAutomated dynamic testing for drying, hardness, and adhesion of paints, coatings, and adhesives / Ronald T. Obie in COATINGS TECH, Vol. 19, N° 2 (02/2022)
PermalinkAutoSock - La solution pour l'adhérence des véhicules sur sols enneigés ou verglacés / Burkhard Böningk in TEXTILES A USAGES TECHNIQUES (TUT), N° 67 (03-04-05/2008)
PermalinkBamboo fiber reinforced composite / Manasi Shinde in MAN-MADE FIBERS INTERNATIONAL, Vol. 74, N° 1 (2024)
PermalinkBeyond the limits of the comparative tracking index / Wim Denissen in KUNSTSTOFFE INTERNATIONAL, Vol. 110, N° 1 (01/2020)
PermalinkBiaxial warp-knitted textiles with symmetrical layers for molted thermoplastic composites / Eveline Hufnagl in CHEMICAL FIBERS INTERNATIONAL, Vol. 65, N° 5 (12/2015)
Permalink