Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Adhesion tendency of polymers to hard coatings / M. Rebelo de Figueiredo in INTERNATIONAL POLYMER PROCESSING, Vol. XXVIII, N° 4 (08/2013)
[article]
Titre : Adhesion tendency of polymers to hard coatings Type de document : texte imprimé Auteurs : M. Rebelo de Figueiredo, Auteur ; C. Bergmann, Auteur ; C. Ganser, Auteur ; C. Teichert, Auteur ; Christian Kukla, Auteur ; C. Mitterer, Auteur Année de publication : 2013 Article en page(s) : p. 415-420 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Adhésion
Dureté (matériaux)
Energie de surface
Mesure
Moules d'injection
Nitrure de chrome
Polyamide 66
Polyéther éther cétone
Polyoxyméthylène
Pulvérisation cathodique
Revêtement métallique
Spectroscopie Raman
Tribologie (technologie)Index. décimale : 668.4 Plastiques, vinyles Résumé : The adhesion tendency of the polymers polyoxymethylene , polyamide 6.6 and polyether ether ketone against hard coatings to protect molds in polymer processing was evaluated by a combination of tribological tests, investigations of wear tracks and measurements of the coatings’ surface energies. It was found that a low surface roughness and a low surface energy of the coating are beneficial to reduce friction and adhesion tendency. Among the coating materials investigated, CrN seems to be the most promising candidate for the protection of molds for polymer processing. DOI : 10.3139/217.2767 En ligne : https://drive.google.com/file/d/1J1hu0CSNp6ErJFQn18IoHiy3BEAD1K_v/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=19286
in INTERNATIONAL POLYMER PROCESSING > Vol. XXVIII, N° 4 (08/2013) . - p. 415-420[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 15396 - Périodique Bibliothèque principale Documentaires Disponible Améliorer sa productivité grâce à des capteurs / Valérie Frèrejean in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 907 (11/2013)
[article]
Titre : Améliorer sa productivité grâce à des capteurs Type de document : texte imprimé Auteurs : Valérie Frèrejean, Auteur ; Jean-François Berthier, Auteur ; Ronan Le Goff, Auteur Année de publication : 2013 Article en page(s) : p. 52-57 Langues : Français (fre) Catégories : Capteurs (technologie)
Matières plastiques -- Moulage par injection -- Appareils et matériel
Moules d'injection
Outillage
Production -- Gestion
ProductivitéIndex. décimale : 668.4 Plastiques, vinyles Résumé : Le projet européen Mold4ProdE est consacré à l'amélioration de la productivité par l'instrumentalisation des moules. Principe retenu : les capteurs rendent les moules intelligents et les transformateurs compétitifs. Note de contenu : - Instrumentation et système d'acquisition et de contrôle : la notion de signature de l'outillage
- Evaluation des gains en phase de mise au point et à chaque redémarrage de production
- Approche numérique pour optimiser le nombre et le positionnement des capteurs
- Diffuser la bonne parole : l'importance de la formation
- Mold4ProdE, un consortium européen à organisation matricielle
- PSP, un système d'acquisition à évaluer
- La formule de calcul du ratio coût/bénéfice (CB)
- Recommandations pour l'implantation des capteurs de pression dans le moule
- Recommandations pour l'implantation des capteurs de températures dans le moulePermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=19872
in PLASTIQUES & CAOUTCHOUCS MAGAZINE > N° 907 (11/2013) . - p. 52-57[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 15761 - Périodique Bibliothèque principale Documentaires Disponible Application of dry nano powder inverse imprint technology in transferring and replication of micro patterns in INTERNATIONAL POLYMER PROCESSING, Vol. XXVII, N° 1 (03/2012)
[article]
Titre : Application of dry nano powder inverse imprint technology in transferring and replication of micro patterns Type de document : texte imprimé Année de publication : 2012 Article en page(s) : p. 105-110 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Impression sur matières plastiques
Moules d'injection
Nanoparticules
Plasmas (gaz ionisés)
PolydiméthylsiloxaneLe polydiméthylsiloxane —[O-Si(CH3)2]n—, ou poly(diméthylsiloxane) selon la nomenclature systématique, communément appelé PDMS ou diméthicone, est un polymère organominéral de la famille des siloxanes souvent présent dans les shampoings. On l'y ajoute pour augmenter le volume des cheveux mais il peut également aller boucher les pores du cuir chevelu et rendre les cheveux gras. C'est une des raisons pour lesquelles se laver les cheveux tous les jours est très déconseillé avec un shampooing contenant des silicones.
Il existe également de l'amodiméthicone, qui est un dérivé du diméthicone.
Le polydiméthylsiloxane est un additif alimentaire (E900), utilisé comme antimoussant dans les boissons (Coca-Cola BlāK).
La chaîne de poly(diméthylsiloxane) forme également la structure de base des huiles et des caoutchoucs silicones.
Polyméthacrylate de méthyleLe poly(méthacrylate de méthyle) (souvent abrégé en PMMA, de l'anglais Poly(methyl methacrylate)) est un polymère thermoplastique transparent obtenu par polyaddition dont le monomère est le méthacrylate de méthyle (MMA). Ce polymère est plus connu sous son premier nom commercial de Plexiglas (nom déposé), même si le leader global du PMMA est Altuglas International9 du groupe Arkema, sous le nom commercial Altuglas. Il est également vendu sous les noms commerciaux Lucite, Crystalite, Perspex ou Nudec.
Poudres
Résines photosensiblesIndex. décimale : 668.9 Polymères Résumé : This research aims to develop a new dry nano powder inverse imprint technology, and probe into transferring and replication of micro patterns. First, a polydimethylsiloxane (PDMS) mould surface, with micro patterns of grating structures, undergo activation treatment with oxygen plasma in order to improve mould surface energy, and thus, spin coat photoresist onto the surface more easily. Then, the surface is heated to restore its hydrophobicity, and by means of nano powder, micro patterns are transfer printed onto the polymethylmethacrylate (PMMA). Research results show that dry nano powder soft coat transferring and forming technology can accurately reproduce the required patterns. In the experiment, gas assisted nano powder imprint technology is used to apply even pressure, coupled with even temperature rise for solidification, then, patterns can be effectively transfer printed and completely formed. Further, these patterns are in perfect contact with the PMMA surface, thus, greatly increasing the valid imprint area and enhancing transferring reproductiveness. The technology integrates technologies, such as, soft lithography, solidifying photoresist, and gas assisted pressure application, and is utilized to transfer print micro patterns in a grating structure, and thus, complete the transferring process of dry micro structure patterns. Note de contenu : - EXPERIMENTAL SETUP : Nano powder imprint device, PDMS structure mould and ink - Surface treatment with oxygen plasma and transferring mechanism - Dry nano powder inverse imprint process
- RESULTS AND DISCUSSION : effect on PDMS surface contact angle before and after oxygen plasma treatment - Effect of different heating temperatures on PDMS surface contact angle after oxygen plasma treatment - Gas assisted nanon powder pressure-applying evennes
- DISCUSSION OF REPLICATED FORMING CHARACTERISTICSDOI : 10.3139/217.2438 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=13739
in INTERNATIONAL POLYMER PROCESSING > Vol. XXVII, N° 1 (03/2012) . - p. 105-110[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 13722 - Périodique Bibliothèque principale Documentaires Disponible As precise and reliable as clockwork / Michael Thielen in KUNSTSTOFFE INTERNATIONAL, Vol. 105, N° 11 (11/2015)
[article]
Titre : As precise and reliable as clockwork : Werkzeugbau Ruhla relies on standardized DLC-coated components Type de document : texte imprimé Auteurs : Michael Thielen, Auteur Année de publication : 2015 Article en page(s) : p. 25-26 Langues : Anglais (eng) Catégories : Moules d'injection
Revêtements protecteursIndex. décimale : 668.4 Plastiques, vinyles Résumé : For toolmaker Werkzeugbau Ruhla in Seebach/Thuringia, Germany, precision and reliability have a long tradition. The company, whose roots lie in the watchmaking industry, has been using DLC-coated standardized parts from Hasco since 2012. The coating reduces wear and thereby increases the service life of high-performance molds in particular. Also the associated freedom of lubricants promises competitive advantages. Note de contenu : - Clean, with minimum wear thanks to DLC
- Advantages for service, maintenance -and customer retentionEn ligne : https://drive.google.com/file/d/1e9PqLS1rKUC1yBiRQamfLuPipQeyqOR1/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=24980
in KUNSTSTOFFE INTERNATIONAL > Vol. 105, N° 11 (11/2015) . - p. 25-26[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 17618 - Périodique Bibliothèque principale Documentaires Disponible Attractive all-round talents / Peter Wippenbeck in KUNSTSTOFFE INTERNATIONAL, Vol. 100, N° 12 (12/2010)
[article]
Titre : Attractive all-round talents Type de document : texte imprimé Auteurs : Peter Wippenbeck, Auteur Année de publication : 2011 Article en page(s) : p. 19-22 Langues : Anglais (eng) Catégories : Moules d'injection Index. décimale : 668.4 Plastiques, vinyles Résumé : Mold Technology - Believe it or not, the K 2010 catalog contained 228 exhibitors connected with mold making. It is an almost unmanageable wealth of information, and, even if you wander through the Internet display rooms, it is still necessary to make a preselection. In any case, the abundance of the offering shows the importance of the industry, which usually operates in the background of spectacular events – though it produces plenty of inspiring ideas itself. Note de contenu : - Maximum automation
- Microcavities and angled parts
- Innovations in standards
- Hot runners - a long-running success
- Laterally "around the corner"
- On th gentle tour
- A question of aestheticsPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=10779
in KUNSTSTOFFE INTERNATIONAL > Vol. 100, N° 12 (12/2010) . - p. 19-22[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 012687 - Périodique Bibliothèque principale Documentaires Disponible Automated mold heating system using high frequency induction with feedback temperature control / K. Park in INTERNATIONAL POLYMER PROCESSING, Vol. XXVI, N° 5 (11/2011)
PermalinkAward-wining packaging solution increases productivity / Henning Becker in KUNSTSTOFFE INTERNATIONAL, Vol. 110, N° 9 (2020)
PermalinkPermalinkA better understanding of demolding / Maximilian Schönherr in PLASTICS INSIGHTS, Vol. 113, N° 7 (2023)
PermalinkCalculation reaps benefits / Andreas Reich in KUNSTSTOFFE INTERNATIONAL, Vol. 106, N° 6-7 (06-07/2016)
PermalinkCanaux chauds : éviter les embûches / Miguel K. Ritto in CAOUTCHOUCS & PLASTIQUES, N° 715 (06-07/1992)
PermalinkComment optimiser la régulation des moules ? / Jean-Marc Maucotel in CAOUTCHOUCS & PLASTIQUES, N° 717 (10/1992)
PermalinkPermalinkLa déformation des outillages maîtrisée / Jean-François Luye in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 857 (05/2008)
PermalinkUne démarche structurée de conformal cooling / Guillaume Vansteenkiste in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 886 (07-08/2011)
PermalinkDesign methodology for parts subject to internal pressure / Thorsten Krumpholz in KUNSTSTOFFE INTERNATIONAL, Vol. 112, N° 2 (2022)
PermalinkDetermination of thermal response on mold surface and recommendation of feasible heating time and gas flow rate for a circular cavity by gas preheating / S.-W. Chang in INTERNATIONAL POLYMER PROCESSING, Vol. XXVII, N° 1 (03/2012)
PermalinkDouble sided gating with needle valve / Eveline Geppert in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 11 (11/2013)
PermalinkEfficient side gating / Peter Braun in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 9 (09/2013)
PermalinkElectrically-heated ceramic composite tooling for out-of-autoclave manufacturing of large composite structures in SAMPE JOURNAL, Vol. 47, N° 4 (06-07/2011)
PermalinkElectroformed moulds in JEC COMPOSITES MAGAZINE, N° 57 (05/2010)
PermalinkErgonomic change in a limited space / F. Stephan Auch in KUNSTSTOFFE INTERNATIONAL, Vol. 110, N° 10 (2020)
PermalinkEvaluation of vacuum venting for micro-injection molding / S.-H. Yoon in INTERNATIONAL POLYMER PROCESSING, Vol. XXVI, N° 4 (09/2011)
PermalinkPermalinkExpedient combination instead of wasteful installation / Walter Michaeli in KUNSTSTOFFE INTERNATIONAL, Vol. 101, N° 2 (02/2011)
PermalinkExperimental study on the filling of nano structures with infrared mold surface heating / H.-Y. Lin in INTERNATIONAL POLYMER PROCESSING, Vol. XXVI, N° 1 (03/2011)
PermalinkExtending the life and improving the performance of plastic injection moulds in POLYMERS PAINT COLOUR JOURNAL - PPCJ, Vol. 208, N° 4642 (06/2018)
PermalinkFabrication of double-sided micro-lens array using UV injection molding / X.-L. Chen in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 1 (03/2019)
PermalinkFabrication of superhydrophobic polyethylene parts by rotomolding / Zaita Ortega in INTERNATIONAL POLYMER PROCESSING, Vol. XXXI, N° 1 (03/2016)
PermalinkPermalinkFine channels, maximum efficiency / Andreas Wonisch in KUNSTSTOFFE INTERNATIONAL, Vol. 109, N° 9 (09/2019)
PermalinkFlawless and consistent deep drawing of polymers moulds in ADHESION - ADHESIVES + SEALANTS, Vol. 16, N° 4/2019 (2019)
PermalinkPermalinkA fresh breeze for the caravan / Hans-Jörg Schreyer in KUNSTSTOFFE INTERNATIONAL, Vol. 102, N° 12 (12/2012)
PermalinkFrom simple filter to a product with added value / Armin Kölz in KUNSTSTOFFE INTERNATIONAL, Vol. 104, N° 1 (01/2014)
PermalinkFully automatic machining, cleaning and measuring in INTERNATIONAL SURFACE TECHNOLOGY (IST), Vol. 8, N° 3 (2015)
PermalinkFunction-integrated lightweight construction for mass production / Christian Hopmann in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 9 (09/2013)
PermalinkPermalinkPermalinkHybrid moulds with epoxy-based composites – effects of materials and processing on shrinkage and warpage / P. G. Martinho in INTERNATIONAL POLYMER PROCESSING, Vol. XXVI, N° 3 (07/2011)
PermalinkIcecold to higher quality and productivity / Steve Wilson in KUNSTSTOFFE INTERNATIONAL, Vol. 106, N° 11 (11/2016)
PermalinkImpressive experience / Rolf-Uwe Müller in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 10 (10/2013)
PermalinkIn between industry 4.0 and market intelligence / Wolfgang Boos in KUNSTSTOFFE INTERNATIONAL, Vol. 108, N° 10 (10/2018)
PermalinkPermalinkInfluence of mold cavity thickness on electrical, morphological and thermal properties of polypropylene/carbon micromoldings / Shengtai Zhou in INTERNATIONAL POLYMER PROCESSING, Vol. 38, N° 2 (2023)
PermalinkInfluence of mold temperature on mold filling behavior and part properties in micro injection molding / S. Meister in INTERNATIONAL POLYMER PROCESSING, Vol. XXVIII, N° 5 (11/2013)
PermalinkA knowledge management system for injection molds / Maximilian Hirner in KUNSTSTOFFE INTERNATIONAL, Vol. 102, N° 7 (07/2012)
PermalinkLaser-based dynamic mold temperature control in KUNSTSTOFFE INTERNATIONAL, Vol. 105, N° 1-2 (01-02/2015)
PermalinkPermalinkLet off some air ! / Rudolf Hein in KUNSTSTOFFE INTERNATIONAL, Vol. 101, N° 11 (11/2011)
PermalinkLeveraging hidden potential / Florian Raschke in KUNSTSTOFFE INTERNATIONAL, Vol. 102, N° 11 (11/2012)
PermalinkLimitations of simple flow models for the simulation of nanoimprint / H. Teyssèdre in INTERNATIONAL POLYMER PROCESSING, Vol. XXVIII, N° 1 (03/2013)
PermalinkLosing pounds and cutting costs with injection compression molding / Serkan Fidan in KUNSTSTOFFE INTERNATIONAL, Vol. 106, N° 11 (11/2016)
PermalinkMaintenance during (nearly) uninterrupted production : Pipette tips / Sabine Kob in KUNSTSTOFFE INTERNATIONAL, Vol. 111, N° 3 (2021)
PermalinkMass production in medical technology demands top precision in tiny details / Uwe Becker in KUNSTSTOFFE INTERNATIONAL, Vol. 105, N° 11 (11/2015)
PermalinkMold makers are raising their game / Nicolai Lammert in KUNSTSTOFFE INTERNATIONAL, Vol. 104, N° 11 (11/2014)
PermalinkMold platforms for IVD consumables / Guido Radig in KUNSTSTOFFE INTERNATIONAL, Vol. 112, N° 2 (2021)
PermalinkLe moule accélère l'assemblage / Alexandre Couto in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 902 (04-05/2013)
PermalinkMoules de grande taille, les atouts français / Audrey Loubens in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 888 (10/2011)
PermalinkMulti-layer counter-pressure injection molding for thick-walled optical lens / Y. Liu in INTERNATIONAL POLYMER PROCESSING, Vol. 36, N° 2 (2021)
PermalinkMultifunctional trade-fair give-away / Michael Thielen in KUNSTSTOFFE INTERNATIONAL, Vol. 109, N° 1-2 (01-02/2019)
PermalinkNew application areas for cube molds on standard machines in KUNSTSTOFFE INTERNATIONAL, Vol. 110, N° 2 (02/2020)
PermalinkNitrogen on tap - not from the bottle / Markus Berninger in KUNSTSTOFFE INTERNATIONAL, Vol. 110, N° 6 (2020)
PermalinkOne tool, one shot, three parts / Simon Wurzbacher in KUNSTSTOFFE INTERNATIONAL, Vol. 113, N° 2 (2023)
PermalinkDes outillages innovants pour la fusion laser / Guillaume Vansteenkiste in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 909 (01-02/2014)
PermalinkPharmaceutical primary packaging with no risk of breakage / Berthold Schopferer in KUNSTSTOFFE INTERNATIONAL, Vol. 113, N° 4 (2023)
PermalinkPlatinno veut rendre la plasturgie compétitive / Valérie Frèrejean in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 874 (03-04/2010)
PermalinkLes polymères en pointe / Hubert Mueller in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 885 (06/2011)
PermalinkPrecision gating in confined spaces / Henning Becker in KUNSTSTOFFE INTERNATIONAL, Vol. 107, N° 5 (05/2017)
PermalinkPrinting the future of particle-foam processing / Johannes Schütz in KUNSTSTOFFE INTERNATIONAL, Vol. 108, N° 8 (08/2018)
PermalinkProcess-optimized production with unscrewing system in KUNSTSTOFFE INTERNATIONAL, Vol. 107, N° 5 (05/2017)
PermalinkDu process à la pièce : l'injection des plastiques / Thomas Munch / Huningue : VTP Editions (2006)
PermalinkProcess simulation-based design, mold construction and mechanical performance evaluation of an insert-injection molded themoplastic polyurethane part / C. Quintana in INTERNATIONAL POLYMER PROCESSING, Vol. XXXV, N° 4 (08/2020)
PermalinkLa propreté des aciers : une longue conquête scientifique et technologique de la sidérurgie - Partie III : nuances d’aciers pour lesquelles la propreté globale est décisive quant aux propriétés d’emploi - Partie III / J. Le Coze in MATERIAUX & TECHNIQUES, Vol. 103, N° 5 (2015)
PermalinkLa qualité au moindre coût / John Gosden in CAOUTCHOUCS & PLASTIQUES, N° 745 (11/1995)
PermalinkQuality from the depth of the mold / Christopherus Bader in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 6 (06/2013)
PermalinkRadius-Pultrusion (TM) widens the bordres of profile manufacturing / Klaus Jansen in JEC COMPOSITES MAGAZINE, N° 47 (03-04/2009)
PermalinkReliable and efficient processing of COC and COP / Eberhard Dengler in KUNSTSTOFFE INTERNATIONAL, Vol. 104, N° 5 (05/2014)
PermalinkSavings potential in dynamic temperature control / Benno Bucher in KUNSTSTOFFE INTERNATIONAL, Vol. 108, N° 8 (08/2018)
PermalinkPermalinkShedding light on a lighter mold / Monika Riedl in KUNSTSTOFFE INTERNATIONAL, Vol. 104, N° 11 (11/2014)
PermalinkSimulations of heat transfer in thermoplastic injection molds manufactured by additive techniques / L. Sardo in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 1 (03/2019)
PermalinkStart of a new era / Armin Daniel in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 10 (10/2013)
PermalinkStructural analysis examining the mold deformation behavior for the detection of the flash in the injection mold / J. H. Choi in INTERNATIONAL POLYMER PROCESSING, Vol. XXIX, N° 4 (08/2014)
PermalinkDes superfinitions sans toilage manuel / Delphine Vaudoux in TRAVAIL & SECURITE, N° 802 (02/2019)
PermalinkThe effects of various variotherm processes and their mechanisms on injection molding / C.-T. Huang in INTERNATIONAL POLYMER PROCESSING, Vol. XXVI, N° 3 (07/2011)
PermalinkThe four sides of a cube / Thorsten Thümen in KUNSTSTOFFE INTERNATIONAL, Vol. 102, N° 9 (09/2012)
PermalinkThe key to efficient production of a hybrid part / Jörg Essinger in KUNSTSTOFFE INTERNATIONAL, Vol. 105, N° 1-2 (01-02/2015)
PermalinkThe soft component first / Horst-Werner Bremmer in KUNSTSTOFFE INTERNATIONAL, Vol. 109, N° 3 (03/2019)
PermalinkThermal mold design in consideration of the temperature control fluid flow / Christian Hopmann in INTERNATIONAL POLYMER PROCESSING, Vol. XXVIII, N° 4 (08/2013)
PermalinkThree-dimensional melt flow system in the hot runner manifold block / Simon Wurzbacher in KUNSTSTOFFE INTERNATIONAL, Vol. 113, N° 4 (2023)
PermalinkThree rotations to the cupholder / Stefan Nix in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 11 (11/2013)
PermalinkToday’s vision of the future / Vaculik, Robert in KUNSTSTOFFE INTERNATIONAL, Vol. 107, N° 9 (09/2017)
PermalinkPermalinkTwice as fast with nitrogen cooling / Sultan Süzer Ilbay in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 8 (08/2013)
PermalinkPermalinkUsing breathing signals for process optimization / Georg Pillwein in KUNSTSTOFFE INTERNATIONAL, Vol. 110, N° 1 (01/2020)
PermalinkUsing a visualization mold to discuss the influence of gas counter pressure and molt temperature on the fountain flow effect / Wen-Ren Jong in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIII, N° 2 (05/2018)
PermalinkUV-curable technique of magnetic roller soft mold and microstructure pattern replication / Y. J. Weng in INTERNATIONAL POLYMER PROCESSING, Vol. XXX, N° 1 (03/2015)
PermalinkPermalinkVisualization analysis of resin flow behavior around a flow front using a rotary runner exchange system / Y. Kanetoh in INTERNATIONAL POLYMER PROCESSING, Vol. XXVII, N° 3 (07/2012)
PermalinkWhen standard is not enough / Armin Kölz in KUNSTSTOFFE INTERNATIONAL, Vol. 98, N° 9/2008 (09/2008)
PermalinkWhen validated quality is not a competitive advantage / Vaculik, Robert in PLASTICS INSIGHTS, Vol. 113, N° 6 (2023)
PermalinkWith an automated process chain and a digital twin / Gerald Erdmann in KUNSTSTOFFE INTERNATIONAL, Vol. 113, N° 3 (2023)
PermalinkWorking with instead of against one another / Mathias Schläger in KUNSTSTOFFE INTERNATIONAL, Vol. 107, N° 1-2 (01-02/2017)
Permalink