Adhesion and weathering performance of waterborne coatings applied to different temperate and tropical wood species / Jan van den Bulcke in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 3, N° 3 (07/2006)

[article]  inJOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 3, N° 3 (07/2006) . - p. 185-191 Titre : Adhesion and weathering performance of waterborne coatings applied to different temperate and tropical wood species Type de document : texte imprimé Auteurs : Jan van den Bulcke, Auteur ; Marc Stevens, Auteur ; Joris van Acker, Auteur ; Veerle Rijckaert, Auteur Année de publication : 2006 Article en page(s) : p. 185-191 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Adhésion Bois -- Revêtements protecteurs Chimie des surfaces Conifères Etudes comparatives Haut extrait sec Polyacryliques Polyalkydes Revêtements -- Détérioration:Peinture -- Détérioration Revêtements -- Effets de la température:Peinture -- Effets de la température Revêtements en phase aqueuse:Peinture en phase aqueuse Index. décimale : 667.9 Revêtements et enduits Résumé : Wood is a renewable material that has been recognized for a long time as a valuable material for construction and engineering. Sound, solid wood can last for centuries. Nevertheless, wood is susceptible to biological and physical degradation. Therefore it needs to be protected properly, all the more when using less durable species. A variety of finishes can be applied. These coatings must meet certain minimum requirements, among which are sufficient penetration, resistance to physical and biological discoloration, and good adhesion. The last is considered the utmost important factor for the overall performance of a coating. Without an adequate anchoring to the wood, the coating will peel off prematurely and, thus, affect the lifetime of the substrate. In this article, the impact of the type of coating used, the wood species, and preweathering of the wood on adhesion are disclosed. In addition, the effect of weathering on the wood-coating system as a whole is looked at as well. The adhesion measurements were obtained with a mechanical torque device developed at VTT in Finland. Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3691 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
005076	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Adhesion measurement methods / Robert Lacombe / Berlin [Germany] : Walter de Gruyter GmbH 

Titre : Adhesion measurement methods : Theory and practice Type de document : document électronique Auteurs : Robert Lacombe, Auteur Editeur : Berlin [Germany] : Walter de Gruyter GmbH Importance : 439 p. Présentation : ill. Note générale : Index - Bibliogr. Langues : Anglais (eng) Catégories : Adhésion Chimie des surfaces Interfaces (Sciences physiques) Mesure Index. décimale : 668.3 Adhésifs et produits semblables Note de contenu : - OVERVIEW OF MOST COMMON ADHESION MEASUREMENT METHODS : Peel test - Tape peel test - Pull test - Indentation debonding test - Scratch test - Blister test - Beam-bending tests - Self-loading tests - More exotic adhesion measurement methods - Electromagnetic test - Nondestructive tests - Surface acoustic waves test - THEORETICAL FOUNDATIONS OF QUANTITATIVE ADHESION MEASUREMENT METHODS : Introduction to continuum theory - Examples - Solving the field equations - Application of simple beams - General methods for solving field equations of elasticity - Numerical methods - Detailed stress behavior of a flexible coating on a rigid disk - Strain energy principles - The marvelous mysterious J integral - ELEMENTARY FRACTURE MECHANICS OF SOLIS : APPLICATION PROBLEMS OF ADHESION : Fracture mechanics as applied to problems of Adhesion - APPLIED ADHESION TESTING : The peel test - Fully quantitative peel testing - The scratch/cut test - The pull test - ADHESION ASPECTS OF COATING AND THIN FILM STRESSES : General measurement methods for thin films and coatings - CASE STUDY FROM THE FIELD : A study in adhesion sensitivity to contamination - Case of the improperly cured film - Case of the stressed pin - Stability maps - APPENDIX : A. Vectors and vector calculus - B. Notes on elementary strength of materials (SOM) theory - C. Material property data for selected substances - D. Driving force formulae for a variety of laminate structures - E. Selected references and commentary on adhesion measurement and film stress literature - F. General adhesion measurement references Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=24684

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire

Documents numériques

Adhesion Measurement Methods : Theory and practice URL

Adhesive bonding efficiency of concrete interfaces / Martin Brandtner-Hafner in ADHESION - ADHESIVES + SEALANTS, Vol. 20, N° 1/2023 (2023)  

[article]  inADHESION - ADHESIVES + SEALANTS > Vol. 20, N° 1/2023 (2023) . - p. 30-33 Titre : Adhesive bonding efficiency of concrete interfaces Type de document : texte imprimé Auteurs : Martin Brandtner-Hafner, Auteur Année de publication : 2023 Article en page(s) : p. 30-33 Note générale : Bibliogr. Langues : Multilingue (mul) Catégories : Chimie des surfaces Evaluation Matériaux cimentaires -- Collage Polymères Index. décimale : 668.3 Adhésifs et produits semblables Résumé : In the construction industry, various polymeric adhesive systems are used for bonding concrete composites. The main focus is on structural safety at the interface between substrate and adhesive. To ensure a risk-adjusted selection of such systems, alternative holistic as well as empirical evaluation methods are needed, since standardized mechanical test methods are not suitable for this purpose. Note de contenu : - Methods - Reverse failure engineering - Adhesion bonding quality - Failures modes - Damage shielding - Adhesive bonding efficiency - Evaluation procedure - Fig. 1 : Setup principle of pull-off test for testing bonded concrete structures - Fig. 2 : Principle of reversed failure engineering based on holistic fracture analysis - Fig. 2 : Peer-safety portfolio of polymeric adhesive systems for bonded concrete structures - Table 1 : Evaluation adhesive bonding systems used on concrete interfaces En ligne : https://drive.google.com/file/d/1u8LyXdvxq1pZ28QgAsu58DqkN4w-l0CG/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=38949 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
23909	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Advanced techniques for nanocharacterization of polymeric coating surfaces / Xiaohong Gu in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 1, N° 3 (07/2004)  

[article]  inJOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 1, N° 3 (07/2004) . - p. 191-200 Titre : Advanced techniques for nanocharacterization of polymeric coating surfaces Type de document : texte imprimé Auteurs : Xiaohong Gu, Auteur ; N.-K. Chang, Auteur ; Diep Nguyen, Auteur ; Y. C. Jean, Auteur ; Jonathan W. Martin, Auteur ; Tinh Nguyen, Auteur ; Li-Piin Sung, Auteur ; Mark R. VanLandingham, Auteur ; Michael J. Fasolka, Auteur ; T.-Y. Wu, Auteur Année de publication : 2004 Article en page(s) : p. 191-200 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Chimie des surfaces Durée de vie (Ingénierie) Epoxydes Fluoropolymères Microscopie à force atomique Morphologie (matériaux) Prévision, Théorie de la Résistance à l'abrasion Revêtements organiques Surfaces -- Analyse Index. décimale : 667.9 Revêtements et enduits Résumé : Surface properties of a polymeric coating system have a strong influence on its performance and service life. However, the surface of a polymer coating may have different chemical, physical, and mechanical properties from the bulk. In order to monitor the coating property changes with environmental exposures from the early stages of degradation, nondestructive techniques with the ability to characterize surface properties with micro- to nanoscale spatial resolution are required. In this article, atomic force microscopy has been applied to study surface microstructure and morphological changes during degradation in polymer coatings. Additionally, the use of AFM with a controlled tip-sample environment to study nanochemical heterogeneity and the application of nanoindentation to characterize mechanical properties of coatings surfaces are demonstrated. The results obtained from these nanometer characterization techniques will provide a better understanding of the degradation mechanisms and a fundamental basis for predicting the service life of polymer coatings. DOI : 10.1007/s11998-004-0012-4 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-004-0012-4.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3899 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
000587	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Alkyl poly glucosides (APGs) surfactants and their properties : a review / Daz Geetha in TENSIDE, SURFACTANTS, DETERGENTS, Vol. 49, N° 5 (09-10/2012)

[article]  inTENSIDE, SURFACTANTS, DETERGENTS > Vol. 49, N° 5 (09-10/2012) . - p. 417-427 Titre : Alkyl poly glucosides (APGs) surfactants and their properties : a review Type de document : texte imprimé Auteurs : Daz Geetha, Auteur ; Rashmi Tyagi, Auteur Année de publication : 2012 Article en page(s) : p. 417-427 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Alkyl polyglycosides Biodégradation Chimie des surfaces Hydrates de carbone Oligomères Surfactants Index. décimale : 668.1 Agents tensioactifs : savons, détergents Résumé : Alkyl polyglucosides are non-ionic surfactants consisting of a hydrophilic saccharide moiety and a hydrophobic fatty alkyl chain. They are synthesized from renewable raw materials and have excellent ecotoxicological profiles and are readily biodegradable. The alkyl polyglucosides are mixtures of homologues, anomers and isomers. The alkyl polyglucosides with a longer alkyl chain biodegrade faster than those with a shorter one. The short to medium alkyl chain containing alkyl polyglucosides are water soluble. They exhibit favorable wetting and surface tension reduction, electrolyte and hard water tolerance, great stability in wide pH range, synergism with other surfactants and act as hydrotropes and dispersants. The dermatological, toxicological, mildness and high compatibility to skin make alkyl polyglucosides superior to all other existing surfactants. They show good functionality in various applications like detergents, food emulsifiers, cosmetic surfactants, industrial emulsifiers and pharmaceutical granulating agents. DOI : 10.3139/113.110212 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=15879 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
14156	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Antistatic performance additive within house and L&L surface cleaning products / Simon Flavin in SOFW JOURNAL, Vol. 142, N° 6 (06/2016)  

Permalink

Application de la RMN et de la fluorescence X / A. Coupard in CAOUTCHOUCS & PLASTIQUES, N° 704 (04/1991)

Permalink

Applied colloid and surface chemistry / Richard M. Pashley / New York [Etats-Unis] : John Wiley & Sons (2004)

Permalink

Approche multi-échelle de l'adhésion polymère-polymère / Marie-France Vallat in CAOUTCHOUCS & PLASTIQUES, N° 828 (02/2005)

Permalink

Bio-based composites for high-performance materials / Wirasak Smitthipong / Boca Raton [Etats-Unis] : CRC Press - Taylor Francis Group (2015)

Permalink

Bis (diquaternary ammonium)salts : synthesis, effect of spacer on surface activities and aggregation properties of reactive red 198 in aqueous – surfactants solutions / Fatma H. Abdel-Salam in TENSIDE, SURFACTANTS, DETERGENTS, Vol. 48, N° 3/2011 (05/2011)

Permalink

Bulletin de liaison N° 26 / Centre Français de l'anticorrosion / Paris : CEFRACOR (2013)

Permalink

Chimie interfaciale et préparation des catalyseurs supportés / Jean-François Lambert in L'ACTUALITE CHIMIQUE, N° 5-6 (05-06/2002)  

Permalink

La chimie organométallique de surface / Frédéric Lefebvre in L'ACTUALITE CHIMIQUE, N° 5-6 (05-06/2002)  

Permalink

Cleaner hulls for cleaner seas / John van Haare in EUROPEAN COATINGS JOURNAL (ECJ), N° 5 (05/2016)  

Permalink

Cohésion à l’interface matrice minérale/fibres cellulosiques : traitements chimiques des fibres et caractérisation / Ali Rachini in MATERIAUX & TECHNIQUES, Vol. 100, N° 5 (2012)  

Permalink

Colloid and interfacial chemistry at Stuttgart University / R. Baum in TENSIDE, SURFACTANTS, DETERGENTS, Vol. 48, N° 3/2011 (05/2011)

Permalink

Colloid chemistry, part I : Definitions and concepts / Vladimir V. Verkholantsev in EUROPEAN COATINGS JOURNAL (ECJ), N° 4/97 (04/1997)

Permalink

Colloid chemistry, part VIII : film forming processes / Vladimir V. Verkholantsev in EUROPEAN COATINGS JOURNAL (ECJ), N° 12/97 (12/1997)

Permalink

Confocal microscope : A valuable tool for examining wood-coating interface / Adya P. Singh in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 1, N° 3 (07/2004)  

Permalink

---

1 2 3 4 5 6 (1 - 20 / 135) Par page : 25 50 100 Tout afficher