Accueil
Résultat de la recherche
11 résultat(s) recherche sur le tag 'Peinture''
Ajouter le résultat dans votre panier Affiner la recherche Générer le flux rss de la recherche
Partager le résultat de cette recherche
Coatings applied on damp building substrates : performance and influence on moisture transport / Vânia Brito in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 8, N° 4 (07/2011)
[article]
Titre : Coatings applied on damp building substrates : performance and influence on moisture transport Type de document : texte imprimé Auteurs : Vânia Brito, Auteur ; Teresa Diaz Gonçalves, Auteur ; Paulina Faria, Auteur Année de publication : 2011 Article en page(s) : p. 513-525 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Revêtements en bâtiment Tags : 'Système peinture' 'Bâtiment ancien' 'Substrat humide' Séchage 'Transport humidité' Index. décimale : 667.9 Revêtements et enduits Résumé : Dampness is a common condition in old buildings and, accordingly, many paint systems specific for this type of building allow for application on walls with nonnegligible moisture content. In spite of that, performance evaluation of these paints is normally carried out using dry substrates or even on free paint films. This article presents research performed on 16 commercial paint systems: seven silicate, three silicone, three hydro-pliolite and two lime-based systems, as well as one common vinyl emulsion paint that served as reference. Each paint was applied and cured both on dry and on damp mortar substrates. The test specimens were subjected to water vapor permeability tests and evaporative drying tests. The following conclusions could be drawn: (i) the way paint systems influence the drying of the substrate, to which they were applied and where they cured, may vary significantly depending on the moisture content of that substrate; (ii) vapor permeability, measured with specimens applied and cured on dry substrate, may be an acceptable way of predicting a paint's influence on drying, provided that the paints are applied and cured on dry substrate or that their characteristics are not significantly affected by the moisture content of that substrate. Note de contenu : MATERIALS : Paint systems - Substrate material
METHODS : Preparation of the test specimens - Water vapor permeability tests Drying tests
DISCUSSION : Effect of the moistening condition of the substrate - Comparison between the performance of the different paint systems - Correlation between vapor permeability and drying indexDOI : 10.1007/s11998-010-9319-5 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-010-9319-5.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=12145
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 8, N° 4 (07/2011) . - p. 513-525[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 013158 - Périodique Bibliothèque principale Documentaires Disponible
[article]
Titre : Shrink-fit manufacturing : Modular paintmaking unit occupies a floorspace of only 30 m2 Type de document : texte imprimé Auteurs : Ralf Hohmann, Auteur Année de publication : 2012 Article en page(s) : p. 20-23 Langues : Anglais (eng) Catégories : Ateliers de peinture industrielle
Système de production
Technique de la productionTags : 'Unité production' 'Production modulaire' 'Fabrication peinture' Nettoyage 'Contrôle automatisé' Index. décimale : 667.9 Revêtements et enduits Résumé : The compact "modular paint factory" concept developed some years ago has now been extended with the introduction of a smaller unit suitable for product and process development and as a production unit for small batches ranging from 300 to 5000 litres Note de contenu : - Standard production procedures summarised
- Advantages of the modular production concept
- Modular production now suits every batch size
- How air entrainment is avoided during dispersion
- Ingredients added without dust or waste
- Cleaning integrated across the entire unit
- Automated control includes maintenance advice
- Production technologies compared
- Future prospectsEn ligne : https://drive.google.com/file/d/1uBxSR8g6YCKDj--qUgCbpxrpZeAVuLTE/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=14724
in EUROPEAN COATINGS JOURNAL (ECJ) > N° 5 (05/2012) . - p. 20-23[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 13885 - Périodique Bibliothèque principale Documentaires Disponible Performance of paint systems after UHP (part 3) / Philippe Le Calvé in PROTECTIVE COATINGS EUROPE (PCE), Vol. 4, N° 1 (01-02-03/2012)
[article]
Titre : Performance of paint systems after UHP (part 3) Type de document : texte imprimé Auteurs : Philippe Le Calvé, Auteur ; Jean-Pierre Pautasso, Auteur Année de publication : 2012 Article en page(s) : p. 38-47 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Acier L'acier est un alliage métallique utilisé dans les domaines de la construction métallique et de la construction mécanique.
L'acier est constitué d'au moins deux éléments, le fer, très majoritaire, et le carbone, dans des proportions comprises entre 0,02 % et 2 % en masse1.
C'est essentiellement la teneur en carbone qui confère à l'alliage les propriétés du métal qu'on appelle "acier". Il existe d’autres métaux à base de fer qui ne sont pas des aciers comme les fontes et les ferronickels par exemple.
Anticorrosion
Atmosphère marine
Corrosion
Essais (technologie)
Métaux -- Nettoyage
Traîtements de surfaceTags : 'Surface métallique' Acier 'Nettoyage eau ultra-haute pression' 'Préparation surface avant peinture' Index. décimale : 667.9 Revêtements et enduits Résumé : Surface preparation processes influence the performance and lifetime of coating systems applied to steel substrates. The state of the steel surface immediately prior to painting is crucial and the main factors influencing the performance are the presence of rust and mill scale, surface contaminants including dust, salts and grease, surface profile. For aggressive environments such as marine atmospheres of C5M corrosivity category and high-performance coatings that require cleaner and/or rougher surfaces, blast cleaning is often the preferred method of surface preparation. However, it is well known that abrasive cleaning can produce a considerable amount of waste mainly containing blasting media, old removed paint and rust products. As an alternative to abrasive cleaning for maintenance work or complete renovation, ultra high pressure (UHP) waterjetting is becoming common as long as the performances of the coatings on steel structures are not affected. UHP waterjetting technology has been described intensively in previous papers. There are however questions about its suitability for new (naval) constructions.
Due to this, a project was started with the purpose of reinforcing the knowledge on the behaviour of different paint systems for highly corrosive marine environments (C5M) and more particularly assessing UHP waterjetting performance in relation to abrasive blasting on steel coated with a zinc-rich shop primer (ZRP).
In the first stage of the study, the characterisation of surfaces after UHP waterjetting of shop primet steel surfaces was reported in the april/june 2011 issue of PCE, and in the second part (reported in july/sep 2011 issue of PCE), the performance of 7 paint systems applied on UHP (DHP 4) treated ZRP coated steel flat panels and welded panels was studied in laboratory and field tests. The results were compared with conventional abrasive blasted (Sa 2.5 MG) surfaces. It was concluded that UHP waterjetting was a promising technique for steel surface preparation within the scope of new constructions (on ZRP coated steel).
The results showed a comparable behaviour of UHP waterjetting with standard surfaces after abrasive blasting. Despite a slight difference in the roughness compared to abrasive blasting, coating performance did not seem to be affected. However, some results remained inconclusive regarding welded panels as a consequence of inhomogeneous weld area.
In this article, the authors describe the third and final part of the study which involved testing three paint systems over UHP waterjetted ZRP panels, including more representative welded panels, compared to conventional grit blast treated panels.Note de contenu : - Experimental conditions
- Test panels, surface preparation and coating
- Artificial ageing test and field test
- Assessments : visual assessment - Pull-off adhesion test - Assessment requirements
- Results : Cyclic corrosion test C5M
- Natural ageingPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=13626
in PROTECTIVE COATINGS EUROPE (PCE) > Vol. 4, N° 1 (01-02-03/2012) . - p. 38-47[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 13694 - Périodique Bibliothèque principale Documentaires Disponible Peintures. Préparation d'un film de peinture par décollement de son support - Norme NF T 30-069 / Association Française de Normalisation (Paris) / Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) (1979)
Titre de série : Peintures Titre : Préparation d'un film de peinture par décollement de son support - Norme NF T 30-069 Type de document : texte imprimé Auteurs : Association Française de Normalisation (Paris) , Auteur Editeur : Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) Année de publication : 1979 Importance : 4 p. Présentation : ill. Format : 30 cm Langues : Français (fre) Catégories : Revêtements -- Normes:Peinture -- Normes Tags : Peinture 'Film peinture' 'Décollement support' Norme Perméabilité 'Vapeur eau' Index. décimale : 667.6 Peintures Résumé : La présente norme a pour objet de décrire une méthode de préparation d'un film de peinture, détaché de son support.
Le film de peinture étant destiné à l'évaluation de propriétés telles que la perméabilité à l'eau, transmission de la vapeur d'eau, la méthode décrite donne les précautions à prendre pour obtenir un film exempt d'altérations susceptibles de modifier ses propriétés physiques.Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=17260 Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 14577 T 30-069 Norme Bibliothèque principale Documentaires Disponible Biocoatings : challenges to expanding the functionality of waterborne latex coatings by incorporating concentrated living microorganisms / Michael C. Flickinger in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 14, N° 4 (07/2017)
[article]
Titre : Biocoatings : challenges to expanding the functionality of waterborne latex coatings by incorporating concentrated living microorganisms Type de document : texte imprimé Auteurs : Michael C. Flickinger, Auteur ; Oscar I. Bernal, Auteur ; Mark J. Schulte, Auteur ; Jessica Jenkins Broglie, Auteur ; Christopher J. Duran, Auteur ; Adam Wallace, Auteur ; Charles B. Mooney, Auteur ; Orlin D. Velev, Auteur Année de publication : 2017 Article en page(s) : p. 791-808 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Biotechnologie
EnzymesUne enzyme est une protéine dotée de propriétés catalytiques. Pratiquement toutes les biomolécules capables de catalyser des réactions chimiques dans les cellules sont des enzymes ; certaines biomolécules catalytiques sont cependant constituées d'ARN et sont donc distinctes des enzymes : ce sont les ribozymes.
Une enzyme agit en abaissant l'énergie d'activation d'une réaction chimique, ce qui accroît la vitesse de réaction. L'enzyme n'est pas modifiée au cours de la réaction. Les molécules initiales sont les substrats de l'enzyme, et les molécules formées à partir de ces substrats sont les produits de la réaction. Presque tous les processus métaboliques de la cellule ont besoin d'enzymes pour se dérouler à une vitesse suffisante pour maintenir la vie. Les enzymes catalysent plus de 5 000 réactions chimiques différentes2. L'ensemble des enzymes d'une cellule détermine les voies métaboliques qui peuvent avoir lieu dans cette cellule. L'étude des enzymes est appelée enzymologie.
Les enzymes permettent à des réactions de se produire des millions de fois plus vite qu'en leur absence. Un exemple extrême est l'orotidine-5'-phosphate décarboxylase, qui catalyse en quelques millisecondes une réaction qui prendrait, en son absence, plusieurs millions d'années3,4. Comme tous les catalyseurs, les enzymes ne sont pas modifiées au cours des réactions qu'elles catalysent, et ne modifient pas l'équilibre chimique entre substrats et produits. Les enzymes diffèrent en revanche de la plupart des autres types de catalyseurs par leur très grande spécificité. Cette spécificité découle de leur structure tridimensionnelle. De plus, l'activité d'une enzyme est modulée par diverses autres molécules : un inhibiteur enzymatique est une molécule qui ralentit l'activité d'une enzyme, tandis qu'un activateur de cette enzyme l'accélère ; de nombreux médicaments et poisons sont des inhibiteurs enzymatiques. Par ailleurs, l'activité d'une enzyme décroît rapidement en dehors de sa température et de son pH optimums.
Microorganismes
Procédés de fabrication
Revêtements en phase aqueuse:Peinture en phase aqueuseTags : Biopeinture Biocatalyseurs 'Peinture en phase aqueuse''Revêtements nanoporeux' 'Ingénierie microbienne dans les peinture' Bioabsorbeurs 'Tolérance à la dessiccation' Index. décimale : 667.9 Revêtements et enduits Résumé : Biocoatings concentrate living, nongrowing microbes in nanoporous adhesive polymer films. Any microbial activity or trait of interest can be intensified and stabilized in biocoatings. These films will dramatically expand the functionality of waterborne coatings. Many microbes contain enzyme systems which are unstable when purified. Therefore, thin polymer coatings of active microbes are a revolutionary approach to stabilize living cells as industrial or environmental biocatalysts. We have demonstrated that some microbes survive polymer film formation embedded in nontoxic adhesive waterborne binders by controlling formulation and drying. Biocoatings can be a single layer of randomly oriented microbes or highly structured multilayer films combining monolayers of different types of microbes on solid, porous, or flexible substrates. They can be formed by drawdown or ink-jet deposition, convective sedimentation assembly, dielectrophoresis, or coated onto or embedded within papers. Controlled drying generates nanoporous microstructure; the pores are filled with a carbohydrate glass which stabilizes the entrapped dehydrated microbes. When the coating is rehydrated, the carbohydrates diffuse out generating nanopores. The activity of biocoatings can be 100s of g L−1 (coating volume) h−1 stabilized for 100–1000s of hours, and therefore, they represent a new approach to process intensification (PI) using thin liquid film bioreactors. A current challenge is that many microbes being engineered as environmental, solar, or carbon recycling biocatalysts do not naturally survive film formation. The mechanisms of dehydration damage that occur during biocoating formulation, ambient drying, and during dry storage have begun to be studied. Critical to preserving microbe viability are minimizing osmotic stress, toxic monomers, biocides, and utilizing polymer chemistries that generate strong wet adhesion with arrested coalescence (nanoporosity). Therefore, controlling desiccation, drying rate/uniformity, and residual moisture are important. Optimization of biocoating activity can be affected at multiple stages—cellular engineering prior to coating (preadaptation), formulation, deposition (film thickness), film formation/drying (generates microstructure), dry storage (minimize metabolic activity), and rehydration. Gene induction (activation) leading to enzyme synthesis following rehydration has been demonstrated. However, little is known about gene regulation in nongrowing microbes. Challenges to optimizing biocoating activity include generating stable film porosity, strong wet adhesion, control of residual water content/form/distribution, and nondestructive measurement of entrapped microbe viability and activity. Indirect methods to measure viability include vital staining, enzyme activity, reporter genes, response to light, confocal fluorescent microscopy, and ATP content. Microbes containing stress-inducible reporter genes can be used to monitor cell stress during formulation, film formation, and drying. Future cellular engineering to optimize biocoatings includes desiccation tolerance, light reactivity (photoefficiency), response to oxidative stress, and cell surface-to-polymer or substrate adhesion. Preservation of microbial activity in waterborne coatings could lead to high intensity biocatalysts for environmental cleaning, gaseous carbon recycling, to produce H2 or electricity from microbial fuel cells, delivery of probiotics, or for biosolar energy harvesting. Note de contenu : - Drying of microorganisms is well established in some industries, but not in coatings
- Early biocoating studies
- Optimization of biocoatings can be affected at multiple stage
- Recent model biocoating systems for gas generation or gas processing
- Challenges to biocoating optimizationDOI : 10.1007/s11998-017-9933-6 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-017-9933-6.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=28921
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 14, N° 4 (07/2017) . - p. 791-808[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19194 - Périodique Bibliothèque principale Documentaires Disponible Impact of regulation on european coating manufacturers / Jacques Warnon in DOUBLE LIAISON, N° 583 (11/2011)
PermalinkInstallations d'application. Cabines d'installation par projection de produit de revêtement en poudre organique / Association Française de Normalisation (Paris) / Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) (2009)
PermalinkPeintures. Détermination de la compatibilté entre deux couches de peintures - Norme NF T 30-063 / Association Française de Normalisation (Paris) / Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) (1976)
PermalinkElectrochromism : electrically controlled color / Robert D. Athey in EUROPEAN COATINGS JOURNAL (ECJ), N° 3/95 (03/1995)
PermalinkSpecular gloss according to ISO 2813 : Influences of angular tolerances / Wolf Czepluch in EUROPEAN COATINGS JOURNAL (ECJ), N° 3/95 (03/1995)
PermalinkVOC protocols and high solid acrylic coatings / Dipak K. Chattopadhyay in PAINTINDIA, Vol. LI, N° 10 (10/2001)
Permalink