Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
The sky is falling ! Or is it paint chips ? / Richard A. Burgess in JOURNAL OF PROTECTIVE COATINGS & LININGS (JPCL), Vol. 34, N° 10 (10/2017)
[article]
Titre : The sky is falling ! Or is it paint chips ? : Failure of a dry-fall coating applied to the interior of previously painted metal decking Type de document : texte imprimé Auteurs : Richard A. Burgess, Auteur Année de publication : 2017 Article en page(s) : p. 10-16 Langues : Américain (ame) Catégories : Analyse des défaillances (fiabilité)
Epaisseur -- Mesure
Epoxydes
Essais d'adhésion
Esters
Métaux -- Revêtements:Métaux -- Peinture
Polyalkydes
Revêtements -- Analyse:Peinture -- Analyse
Spectrométrie infrarougeIndex. décimale : 667.9 Revêtements et enduits Résumé : This month's case was selected from several investigations related to failures that occur when applying coating to the underside of metal deck panels (Fig. 1). This case focuses on an adhesion failure of coatings applied to previously painted deck panels. Note de contenu : - Site investigation
- Laboratory investigation
- The failure mechanism
- Repair recommendations
FIGURES : 1. Metal decking similar to the decking described in this article - 2. Cracked coating and lifted edges on the metal panel wall - 3. Tape adhesion tests performed on the ceiling produced mixed results even in the same vicinity (note thickness values written on surface) - 4. When tapping produced a "hollow" sound, the epoxy ester film was delaminated although appearing visibly intact - 5. Using a sharp blade and chisel to remove different layers of the existing coating system, including the epoxy ester exposed the substrate (black spots), original primer (gray) alkyd coating (yellow/beige) beneath the epoxy ester (white)
TABLES : 1. Coating Thickness Measured over Different Coating Layers - 2. Laboratory-Measured Coating-Thickness Data - 3. Results of Infrared Spectroscopic AnalysisEn ligne : http://www.paintsquare.com/archive/?fuseaction=view&articleid=6148 Format de la ressource électronique : Web Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=29505
in JOURNAL OF PROTECTIVE COATINGS & LININGS (JPCL) > Vol. 34, N° 10 (10/2017) . - p. 10-16[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19362 - Périodique Bibliothèque principale Documentaires Disponible Transparency in wood - safe and secure / Jürgen Benitz-Wildenburg in ADHESION - ADHESIVES + SEALANTS, Vol. 14, N° 2/2017 (2017)
[article]
Titre : Transparency in wood - safe and secure Type de document : texte imprimé Auteurs : Jürgen Benitz-Wildenburg, Auteur ; Karin Lieb, Auteur ; Ulrich Sieberath, Auteur Année de publication : 2017 Article en page(s) : p. 10-13 Note générale : Bibliogr. Langues : Multilingue (mul) Catégories : Assemblages collés
Bois
Collage
Construction -- Matériaux
Essais d'adhésion
Fenêtres -- Conception et construction
Résistance aux conditions climatiques
VerreIndex. décimale : 668.3 Adhésifs et produits semblables Résumé : Architects and builders prefer glass facades and window systems with profiles that are as slim as possible. Structural glazing designs (SG facades) made of aluminium fulfil this requirement andhave been in use for a long time. Now however, composite elements that combine timber and glass have been officially approved by the building authorities. Note de contenu : - Construction and assembly
- Adhesive bond compensates for forces
- Building regulations and requirements
- FIGURES : 1. High transparency and weather resistance on the outside combined with attractiveness of wood on the inside are the advantages of timber-glass composite elements - 2. Horizontal section with bonded fixed glazing and integrated window element - 3. The bonding of the glass elements onto coupling strips in the workshop ensures easy assembly on mullion-transom systems - 4. Details of the mechanical fixture for areas higher than 8 m above the ground (emergency support) - 5. Simple process for checking adhesive behaviour as part of in-house production control/2/ (testing the open time and "split test" for testing the adhesion/cohesion behaviour of semi-elastic adhesivesPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=28692
in ADHESION - ADHESIVES + SEALANTS > Vol. 14, N° 2/2017 (2017) . - p. 10-13[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19013 - Périodique Bibliothèque principale Documentaires Disponible
[article]
Titre : Turning the temperature down : Developing epoxy coatings for heat-sensitive substrates Type de document : texte imprimé Auteurs : Jose Lorenzo, Auteur ; Kenneth Ryan, Auteur ; Joseph Mulvey, Auteur ; Jason Chou, Auteur Année de publication : 2017 Article en page(s) : p. 46-50 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Epoxydes
Essai Wolff-Wilborn
Essais d'adhésion
Essais dynamiques
Flexion (mécanique)
Formulation (Génie chimique)
Matières plastiques -- Revêtement:Matières plastiques -- Peinture
Réticulants
Revêtements poudre:Peinture poudreIndex. décimale : 667.9 Revêtements et enduits Résumé : Standard powder coatings based on epoxy functional methacrylate monomers require high curing temperatures. Replacing the standard monomer and cross-linker allowed good performance to be obtained at lower curing temperatures (80 °C and 90 °C). Powder coatings suitable for plastics could be based on this new chemistry. Note de contenu : - Key differences between monomers
- Experimental chemicals and equipment
- Epoxy resin preparation in detail
- How the coatings were prepared
- Preparation of cross-linker solution
- Results of the preparation procedures summarised
- Superior performance after low-temperature cure
- Lower temperature chemistry demonstrated successfully
- FIGURES : 1. Ring strain of different epoxides - 2. Synthesis apparatus - 3. Melting points of linear saturated dicarboxylic acids showing pattern of differences between odd and even numbers of carbon atoms - 4. Cross-cut adhesion test result (ASTM D 3359) ; highest figures indicate best performance - 5. Toluene rub tests on steel panels - 6. Conical mandrel bend test on steel panels with azelaic acid as the crosslinker - 7. Pencil hardness test on steel panels with azelaic acid as the crosslinker
- TABLES : 1. Composition of the two epoxy resins - 2. Composition of coatings - 3. Properties of the epoxy resins producedEn ligne : https://drive.google.com/file/d/1s_uFhZktlXUsogUZnXRGflxL0RqkBdA5/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=27546
in EUROPEAN COATINGS JOURNAL (ECJ) > N° 1 (01/2017) . - p. 46-50[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 18601 - Périodique Bibliothèque principale Documentaires Disponible
[article]
Titre : Ultra low emission coatings : New amine curing agents meet strict VOC regulations and exhibit robust performance during service life Type de document : texte imprimé Auteurs : Tuncay Zuhal, Auteur Année de publication : 2021 Article en page(s) : p. 44-49 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Amines Une amine est un composé organique dérivé de l'ammoniac dont certains hydrogènes ont été remplacés par un groupement carboné. Si l'un des carbones liés à l'atome d'azote fait partie d'un groupement carbonyle, la molécule appartient à la famille des amides. Découvertes en 1849, par Wurtz les amines furent initialement appelées alcaloïdes artificiels.
On parle d'amine primaire, secondaire ou tertiaire selon que l'on a un, deux ou trois hydrogènes substitués.
Par exemple, la triméthylamine est une amine tertiaire, de formule N(CH3)3.
Typiquement, les amines sont obtenues par alkylation d'amines de rang inférieur. En alkylant l'ammoniac, on obtient des amines primaires, qui peuvent être alkylées en amines secondaires puis amines tertiaires. L'alkylation de ces dernières permet d'obtenir des sels d'ammonium quaternaire.
D'autre méthodes existent : 1. Les amines primaires peuvent être obtenues par réduction d'un groupement azoture, 2. Les amines peuvent aussi être obtenues par la réduction d'un amide, à l'aide d'un hydrure, 3. L'amination réductrice permet l'obtention d'amines substituées à partir de composés carbonylés (aldéhydes ou cétones), 4. Les amines primaires peuvent être obtenues par la réaction de Gabriel.
Anticorrosifs
Anticorrosion
Epoxydes
Essais accélérés (technologie)
Essais d'adhésion
Formulation (Génie chimique)
Primaire (revêtement)
Réduction des composés organiques volatils
Réticulants
Revêtements organiquesIndex. décimale : 667.9 Revêtements et enduits Résumé : Environmental regulations have increased in the marine and protective coatings industries worldwide in recent years. Current worker safety and environmental protection regulations are among the most important drivers in new product development for epoxy coatings, targeting the reduction or elimination of volatile organic compounds (VOCs). Note de contenu : - Keeping up with the regulations
- New products with excellent properties
- Ultra-low emissions
- High performance of anti-corrosive primers
- Fig. 1 : Overview of state-of-the-art epoxy coatings in comparison to newly developed curing agents
- Fig. 2 : Degree of cure for curing agents in combination with modified LEr
- Fig. 3 : Emission testing results for formulation 3 based on Ancamine 2739 curing agent following the AgBB testing scheme
- Fig. 4 : Anti-corrosive primer system based on "Ancaine 2739" after accelerated weathering and pull-off adhesion test
- Table 1 : Performance properties of ew developed curing agents vs modified cycloaliphatic amine
- Table 2 : Performance properties of anti-corrosive primers based on formulations 1 and 2
- Table 3 : Comparison of a bisphenol-A epoxy resin - clear coats at 10°C and 60 % RH
- Table 4 : Anti-corrosive primer start point formulation 1 (F1) based on "Ancamine 2712M" or modified cycloaliphatic curing agents and forulation 2 (F2) based on "Ancamine 2739"
- Table 5 : Stard point formulation based on "Ancamine 2739" prepared for emission testEn ligne : https://drive.google.com/file/d/1o6n8TfLkJmNCGYMhFc-ytDdfPsyIIqYC/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=35857
in EUROPEAN COATINGS JOURNAL (ECJ) > N° 5 (05/2021) . - p. 44-49[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 22759 - Périodique Bibliothèque principale Documentaires Disponible UV-stable electrocoats for corrosion protection and structural bonding in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 16, N° 6 (11/2019)
[article]
Titre : UV-stable electrocoats for corrosion protection and structural bonding Type de document : texte imprimé Année de publication : 2019 Article en page(s) : p. 1609-1618 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Anticorrosifs
Anticorrosion
Colles:Adhésifs
Essais accélérés (technologie)
Essais d'adhésion
Pulvérisation cathodique
Résistance au cisaillement
Résistance aux conditions climatiques
Revêtements:Peinture
Spectroscopie d'impédance électrochimiqueIndex. décimale : 667.9 Revêtements et enduits Résumé : The coating process in the industry segment of mobile machinery for ACE, e.g., agricultural machines, is usually done by spray application after welding a variety of parts on the framework. The current painting process consists of an anticorrosive primer and a weather-resistant topcoat. The presented study is part of a research project investigating a new concept combining a new sequence in construction with the big advantage of applying a single-coat system. This smart production enables the construction of machines in modules, keeps the volume of an electrocoating dipping bath at a minimum level, and replaces the custom painting procedure with much overspray by an economic and ecological coating technology. To realize this new technology, the coating system has to perform as an anticorrosive system, providing a sufficient outdoor weather resistance, and must have sufficient adhesion strength for structural bonding of additional parts. First results show that the investigated electrocoats show good anticorrosive properties. The UV- and the weather resistance meet the required values (> 50% gloss retention after 1000 h artificial weathering of CAM 180), dependent on the type of electrocoat. First investigations on structural bonding show that a high bonding strength can be achieved. Note de contenu : - EXPERIMENTAL METHODS AND MATERIALS : Substrate materials - Pretreatment processes - Adhesives - Cathodic electrodeposition paint - Adhesion test - Corrosion tests - Cyclic corrosion test - Artificial weathering - Electrochemical impedance spectroscopy (EIS) - Tensile shear strength DOI : 10.1007/s11998-019-00266-7 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-019-00266-7.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33413
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 16, N° 6 (11/2019) . - p. 1609-1618[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21321 - Périodique Bibliothèque principale Documentaires Disponible Validation of adhesion characterization methods for antistick coatings applied in cooking systems / Stefano Rossi in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 19, N° 4 (07/2022)
PermalinkVersatile self-crosslinking polyurethane dispersion for low VOC coatings across multiple markets / Aditi Chavannavar in POLYMERS PAINT COLOUR JOURNAL - PPCJ, Vol. 208, N° 4646 (11/2018)
PermalinkWater-dispersible raw materials for hot melt adhesives / Richard A. Miller in ADHESIVES AGE, Vol. 39, N° 12 (11/1996)
Permalink