Accueil
Catégories
> Mesure
MesureVoir aussi
|
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
A change of length has consequences / Natalie Rudolph in KUNSTSTOFFE INTERNATIONAL, Vol. 112, N° 2 (2021)
[article]
Titre : A change of length has consequences : The coefficient of thermal expansion can help to sensure product quality Type de document : texte imprimé Auteurs : Natalie Rudolph, Auteur Année de publication : 2021 Article en page(s) : p. 42-45 Langues : Anglais (eng) Catégories : Analyse thermomécanique
Composites -- Délaminage
Composites à fibres
Composites à fibres -- Moulage par injection
Dilatation (thermodynamique)
Fibres à orientation unidirectionnelle
Mesure
Polyéther éther cétone
PolypropylèneIndex. décimale : 668.4 Plastiques, vinyles Résumé : The design of parts and components made of fiber-reinforced composites needs to take the coefficient of thermal expansion into account because it determines the extent to which a material changes in length when heated or cooled. Neglecting this quality criterion can have far-reaching consequences. Note de contenu : - TMA as tool for studying the expansion behavior
- An understanding of anisotropy is critical to high-performance composites
- Different coefficients of expansion in different directions
- How does the thermal expansion correlate to the flow field ?
- Determining time to delamination of electronic assemblies
- Fig. 1 : TMA measurement on a PP-GF-UD composite material. Sample size 25 mm, heating rate 5 K/min from –70 °C to 140 °C, N2 atmosphere, expansion sample holder made of fused silica
- Fig. 2 : a) Sample extraction location, b) dominant fiber orientation
- Fig. 3 : TMA measurement results of PEEK with short carbon fibers from different part locations; sample 1 = orange; sample 2 = red; sample 3 = green
- Fig. 4 : Determination of time to delamination on an FR4 composite circuit board. Sample size 6.35 mm2 as defined by IPC standard, dried for 2 h pre-measurement at 105 °C, heating rate 10K/min, N2 atmosphere, sample holder made of fused silicaEn ligne : https://drive.google.com/file/d/1SMBww_r2xyAosNvyA0-MpYBYKSBW9mdp/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=35498
in KUNSTSTOFFE INTERNATIONAL > Vol. 112, N° 2 (2021) . - p. 42-45[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 22591 - Périodique Bibliothèque principale Documentaires Disponible Characterising the appearance of liquid binders in EUROPEAN COATINGS JOURNAL (ECJ), N° 10/96 (10/1996)
[article]
Titre : Characterising the appearance of liquid binders : Improvement the colour and turbidity measurement Type de document : texte imprimé Année de publication : 1996 Article en page(s) : p. 712-719 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Caractérisation
Colorimétrie
Etudes comparatives
Liants
Mesure
TurbiditéIndex. décimale : 667.9 Revêtements et enduits Résumé : This article describes the replacement of traditional methods of colour measurement and turbidity evaluation (both usually based on visual interpretation by an operator) by spectrophotometer-based tests. The approach is to introduce the new techniques (principles, theoretical aspects), to compare the old and new ways in practical lab tests and to present conclusions and recommendations. Note de contenu : - COLOUR MEASUREMENT : Colour scales - Pitfalls in testing - Instrumental measurement - requirements - Comparison of suitable instruments - Colour comparison testing : discussion - Colour comparison testing : conclusions
- TURBIDITY MEASUREMENT : Theoretical aspects - Available instruments and testing - Conclusions
- FINAL CONCLUSION/STANDARDISATION : Final conclusion - StandardisationPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=24236
in EUROPEAN COATINGS JOURNAL (ECJ) > N° 10/96 (10/1996) . - p. 712-719[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 002520 - Périodique Bibliothèque principale Documentaires Disponible Characteristics of urushi film prepared through thermal polymerization / Chieko Narita in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 20, N° 4 (07/2023)
[article]
Titre : Characteristics of urushi film prepared through thermal polymerization Type de document : texte imprimé Auteurs : Chieko Narita, Auteur ; Yoko Okahisa, Auteur ; Saori Kitaguchi, Auteur ; Kazushi Yamada, Auteur Année de publication : 2023 Article en page(s) : p. 1299-1310 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Analyse spectrale
Analyse thermique
Angle de contact
Biopolymères
Colorimétrie
Laque et laquage
Laque japonaise
Mesure
Microscopie électronique à balayage
Polymérisation thermique
Revêtements -- Propriétés mécaniques
RugositéIndex. décimale : 667.9 Revêtements et enduits Résumé : Urushi (oriental lacquer) is a natural material that forms thin films with excellent durability and water resistance. There are two methods for curing urushi: oxidative and thermal polymerizations. Urushi is mainly applied to wood; therefore, the oxidative polymerization method has mainly been used to cure it. Oxidative polymerization requires temperature and humidity control and takes a long time to fully cure urushi. Urushi mixed with pigments has poor coloration. In contrast, the use of a thermal polymerization reaction can achieve curing in a short time. In this study, we focused on the thermal curing reaction of urushi, formed 13 different colored urushi coating films, and investigated their properties and coloration. We observed that urushi coatings produced through thermal polymerization took less time to cure than those produced through oxidative polymerization, and that urushi coatings with better coloration and high water repellency were obtained. Note de contenu : - EXPERIMENTAL :
- Materials and preparation of samples
- Measurement methods
- RESULTS AND DISCUSSION :
- FTIR spectroscopy
- DSC
- Color measurements
- UV–visible spectroscopy
- SEM observation
- Surface roughness and contact angle
- Mechanical properties
- Table 1 Correspondence table between pigments and sample name
- Table 2 L*, a*, b*, and C* values of all samples measured using SCI and SCE modes
- Table 3 Surface roughness of the samples G, K, and M obtained via laser microscopyDOI : https://doi.org/10.1007/s11998-022-00745-4 En ligne : https://link.springer.com/content/pdf/10.1007/s11998-022-00745-4.pdf?pdf=button% [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39717
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 20, N° 4 (07/2023) . - p. 1299-1310[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 24153 - Périodique Bibliothèque principale Documentaires Disponible Characterization of anisotropic properties of hot compacted self-reinforced composites (SRCs) via thermal diffusivity measurement / Hans-Peter Heim in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 5 (11/2019)
[article]
Titre : Characterization of anisotropic properties of hot compacted self-reinforced composites (SRCs) via thermal diffusivity measurement Type de document : texte imprimé Auteurs : Hans-Peter Heim, Auteur ; F. Mieth, Auteur ; F. Jakob, Auteur ; M. Schnau, Auteur Année de publication : 2019 Article en page(s) : p. 532–540 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Anisotropie
Caractérisation
Compactage à chaud
Composites thermoplastiques -- Propriétés mécaniques
Composites thermoplastiques -- Propriétés thermiques
Composites thermoplastiques auto-renforcés
Densité
Mesure
Polyéthylène à ultra haut poids moléculaire
Polylactique, AcideL'acide polylactique (anglais : polylactic acid, abrégé en PLA) est un polymère entièrement biodégradable utilisé dans l'alimentation pour l'emballage des œufs et plus récemment pour remplacer les sacs et cabas en plastiques jusqu'ici distribués dans les commerces. Il est utilisé également en chirurgie où les sutures sont réalisées avec des polymères biodégradables qui sont décomposés par réaction avec l’eau ou sous l’action d’enzymes. Il est également utilisé pour les nouveaux essais de stent biodégradable.
Le PLA peut-être obtenu à partir d'amidon de maïs, ce qui en fait la première alternative naturelle au polyéthylène (le terme de bioplastique est utilisé). En effet, l'acide polylactique est un produit résultant de la fermentation des sucres ou de l'amidon sous l'effet de bactéries synthétisant l'acide lactique. Dans un second temps, l'acide lactique est polymérisé par un nouveau procédé de fermentation, pour devenir de l'acide polylactique.
Ce procédé conduit à des polymères avec des masses molaires relativement basses. Afin de produire un acide polylactique avec des masses molaires plus élevées, l'acide polylactique produit par condensation de l'acide lactique est dépolymérisé, produisant du lactide, qui est à son tour polymérisé par ouverture de cycle.
Le PLA est donc l’un de ces polymères, dans lequel les longues molécules filiformes sont construites par la réaction d’un groupement acide et d’une molécule d’acide lactique sur le groupement hydroxyle d’une autre pour donner une jonction ester. Dans le corps, la réaction se fait en sens inverse et l’acide lactique ainsi libéré est incorporé dans le processus métabolique normal. On obtient un polymère plus résistant en utilisant l'acide glycolique, soit seul, soit combiné à l’acide lactique.Index. décimale : 668.4 Plastiques, vinyles Résumé : The mechanical properties of self-reinforced composites (SRCs) produced in a hot compaction process significantly depend on the process parameters. Only a little deviation of the process temperature or pressure causes the component to act differently under mechanical load. This is a chance and a challenge at the same time, since this process is difficult to handle but by properly controlling the process parameters, the mechanical properties can be adjusted, even locally for one component. In this research SRC are manufactured in a hot compaction process. A correlation between process parameters and density is found. Density increased from 0,8 to 0,91 g/cm³ by increasing temperature and pressure in the hot compaction process. The different thermal properties in the direction of orientation (IP) and transverse to orientation (TP) are measured with a laser flash device. It was found that, due to a change in density and molecular orientation, diffusivity and conductivity are influenced in different degrees in IP and TP directions. For interpretation of thermal measurement results, microstructures are analysed with a confocal laser scanning microscope after preparing the specimen with a permanganate etching. A schematic model of conductive path is worked out and discussed. With measurement data the anisotropy of IP and TP diffusivity is calculated, and a model is built to describe relative density related to anisotropy. The highest anisotropy between IP and TP diffusivity was calculated with a ratio of 6 at a relative density of approximately 0,82 g/cm³. Since mechanical properties in correlation to process parameters have already been investigated, results of this investigation, in combination with previous research on mechanical properties, will enable the development of a non-destructive testing method for SRCs by measuring the thermal diffusivity. Note de contenu : - STATE OF TECHNOLOGY
- EXPERIMENTAL STUDIES : Materials - Processing - Preparation - Measuring
- RESULTS : Density - Microscopy - Thermal propertiesDOI : https://doi.org/10.3139/217.3812 En ligne : https://drive.google.com/file/d/1_piOekBofBD3DeQ7_8uKZZgss0mKki6v/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33615
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 5 (11/2019) . - p. 532–540[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21324 - Périodique Bibliothèque principale Documentaires Disponible Characterizing ultrasonic micro-molding process of polyetheretherketone (PEEK) / Tomasz Dorf in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIII, N° 4 (08/2018)
[article]
Titre : Characterizing ultrasonic micro-molding process of polyetheretherketone (PEEK) Type de document : texte imprimé Auteurs : Tomasz Dorf, Auteur ; I. Ferrer, Auteur ; Joaquim Ciurana, Auteur Année de publication : 2018 Article en page(s) : p. 442-452 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Matières plastiques -- Moulage par injection assisté par ultrasons
Matières plastiques -- Moulage par micro-injection
Matières plastiques -- Propriétés mécaniques
Mesure
Polyéther éther cétoneIndex. décimale : 668.4 Plastiques, vinyles Résumé : Ultrasonic micro-molding technology can dispense, melt and inject as small an amount of polymer as is required for one cycle, an advantage which makes the process highly desirable for low-volume and customized production of micro parts made from sensitive and very expensive polymers, especially in the medical sector. In this study, the feasibility of processing the polyetheretherketone (PEEK) polymer was investigated. The experiments conducted determined the parameters of a process that would allow parts with specific mechanical properties to be produced and verified as not degraded. The development of the process used three amplitude values as well as varying plunger velocity and vibration times. The three amplitude values and four speed values were tested to determine appropriate parameters for the ultrasonic process. Completely filled samples without any visual signs of degradation were analysed using FTIR-ATR, crystallinity percentage and tensile strength tests. Results show that the amplitude parameter is an important factor in the ultrasonic process and the higher its value is, the better the mechanical properties of complete parts are. Moreover, the tensile strength value of the specimens fabricated by ultrasonic micro-molding is comparable to that of conventional injection molding technology. Note de contenu : - EXPERIMENTAL SET-UP : Processing material - machine and equipment - Ultrasonic micro-molding process - Specimen manufacturing process - Part analysis and measurements
- RESULTS : Visual analysis of specimens - Degradation - Crystallinity - Tensile strengthDOI : 10.3139/217.3428 En ligne : https://drive.google.com/file/d/1sW6S0qJj6EtfYyAc-yxUudqb_iXOIRbG/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=30883
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIII, N° 4 (08/2018) . - p. 442-452[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 20077 - Périodique Bibliothèque principale Documentaires Disponible PermalinkChemical and characterization and tribological behavior of kitchen chimney dump lard (KCDL) as a bio-lubricant / Suman Dey in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 29, N° 3 (06/2019)
PermalinkChrome sludge compost - Effects on crops and soils / Li Gui-Ju in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 90, N° 1 (01-02/2006)
PermalinkCIDP développe de nouveaux tests en photobiologie / Stela Cristiana Daneasa in EXPRESSION COSMETIQUE, N° 56 (03-04/2019)
Permalink"Classic" biophysical methods for hair & scalp / C. Uhl in GLOBAL PERSONAL CARE, Vol. 22, N° 3 (03/2021)
PermalinkCleanliness inspection directly at the process / André Lohse in INTERNATIONAL SURFACE TECHNOLOGY (IST), Vol. 6, N° 3 (2013)
PermalinkClimate control for concrete / Lars Wolff in POLYMERS PAINT COLOUR JOURNAL - PPCJ, Vol. 193, N° 4468 (09/2003)
PermalinkClosed loop control of the coating thickness in powder coating plants / Alexander Buchmüller in INTERNATIONAL SURFACE TECHNOLOGY (IST), Vol. 8, N° 2 (2015)
PermalinkCoalescence and film formation from latexes / Kenneth L. Hoy in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 68, N° 853 (02/1996)
PermalinkPermalinkCollaborative study for the determination of repeatability and reproductibility of the measurement of the water vapour permeability of leather with method ISO 14268 / Giorgio Pozza in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 100, N° 6 (11-12/2016)
PermalinkColour tolerance for liquid coatings / Chiara Battaglia in SURFACE COATINGS INTERNATIONAL, Vol. 103.4 (07-08/2020)
PermalinkComparison of leather produced from fresh and salted hides / Betty M. Haines in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 59 (Année 1975)
PermalinkComparison of leather produced from fresh and salted hides / Betty M. Haines in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 59, N° 6 (11-12/1975)
PermalinkComparison of the colour fading effects of sodium hypochlorite and ozone treatments / Idil Yigit in COLORATION TECHNOLOGY, Vol. 137, N° 6 (12/2021)
Permalink