Accueil
Catégories
> Matières plastiques -- Moulage par injection -- Appareils et matériel
Matières plastiques -- Moulage par injection -- Appareils et matérielVoir aussi
|
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Variothermal temperature control from the compressed air network / Edwin Neugebauer in KUNSTSTOFFE INTERNATIONAL, Vol. 108, N° 1-2 (01-02/2018)
[article]
Titre : Variothermal temperature control from the compressed air network : Varioplast has developed a dynamic temperature control process which can be retrofitted to injection molds without theneed for any modifications Type de document : texte imprimé Auteurs : Edwin Neugebauer, Auteur ; Michael Däbritz, Auteur Année de publication : 2018 Article en page(s) : p. 13-16 Langues : Anglais (eng) Catégories : Matières plastiques -- Moulage par injection -- Appareils et matériel
Température -- ContrôleIndex. décimale : 668.4 Plastiques, vinyles Résumé : As a manufacturer of both coated and uncoated high-gloss plastic parts, Varioplast has continually been faced with the problem of visible knit and flow lines on molded parts. Conventional variothermal processes, for reasons of overall economics, are limited in their suitability to offset existing and future cost pressures exerted by customers. Varioplast unveiled a new process at Fakuma 2017. Note de contenu : - The idea : hot air from the nozzle
- The heating module : designed for single and double-sided use
- Process parameters : a system with scalable performance
- Test results : production readiness confirmed
- FIGURES : 1. In series production, the finished part is removed on the ejector side, while the cavity is heated in parallel on the nozzle side. The 3D-printed metallic heating head module permits quick adaptation to customer-specific geometries in the mold - 2. The turbotherm modules can be used on the nozzle and ejector side if required - 3. Surface on a molded part with and without turbotherm. A knit line is invisible in the first case, but visible in the second - 4. Representation of the surface temperature of the cavity in the machine cycle. A temperature rise from 5 to 10°C/s is possible, with the exact rate depending on the surface roughness - 5. Representation of the heating power in the machine cycle. The unit requires an average of approx. 1.4 kW power. Variothermal process control via the complete mold plates requires 20 to 30 times as much power - 6. The width of the knit line decreases strongly with heating time. It can be optically reduced by up to 100%, i.e. completely eliminatedEn ligne : https://drive.google.com/file/d/1gxBOXdonL9DepHK1iwwPjPouwMUpjV6T/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=30083
in KUNSTSTOFFE INTERNATIONAL > Vol. 108, N° 1-2 (01-02/2018) . - p. 13-16[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19625 - Périodique Bibliothèque principale Documentaires Disponible Vérins électriques, une autre solution / Carlos Gatoes in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 835 (11/2005)
[article]
Titre : Vérins électriques, une autre solution Type de document : texte imprimé Auteurs : Carlos Gatoes, Auteur Année de publication : 2005 Article en page(s) : p. 24-26 Langues : Français (fre) Catégories : Machines électriques
Matières plastiques -- Moulage par injection -- Appareils et matériel
Outillage
Presses à injecter
Vérins électriquesIndex. décimale : 668.4 Plastiques, vinyles Résumé : Cet article explique comment, avec les presses électriques, il faut envisager de combiner les avantages des vérins électriques pour les mouvements dans le moule à ceux des presses tout électrique. Note de contenu : - Puissance, déplacement et rapidité
- Configurations possiblesPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=23622
in PLASTIQUES & CAOUTCHOUCS MAGAZINE > N° 835 (11/2005) . - p. 24-26[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 003177 - Périodique Bibliothèque principale Documentaires Disponible La vis d'injection ELCee améliore la productivité / Emmanuelle Labat in CAOUTCHOUCS & PLASTIQUES, N° 804 (05/2002)
[article]
Titre : La vis d'injection ELCee améliore la productivité Type de document : texte imprimé Auteurs : Emmanuelle Labat, Auteur Année de publication : 2002 Article en page(s) : p. 40-43 Langues : Français (fre) Catégories : Matériaux -- Application-dosage
Matières plastiques -- Moulage par injection -- Appareils et matériel
ProductivitéIndex. décimale : 668.4 Plastiques, vinyles Résumé : En réponse aux attentes des plasturgistes en matière de réduction des coûts de production, DuPont a imaginé EL-Cee. Une vis d'injection capable de réduire le temps de dosage jusqu'à 50%, tout en améliorant la qualité de la matière à l'état fondu. Note de contenu : - Agir sur le contrôle du cisaillement
- Vitesses de rotation et temps de dosage
- Des résultats d'essai probants
- Des avantages techniques immédiats
- Évaluation préalable des temps de dosagePermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=23880
in CAOUTCHOUCS & PLASTIQUES > N° 804 (05/2002) . - p. 40-43[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 000527 - Périodique Bibliothèque principale Documentaires Disponible Visualization analysis of resin flow behavior around a flow front using a rotary runner exchange system / Y. Kanetoh in INTERNATIONAL POLYMER PROCESSING, Vol. XXVII, N° 3 (07/2012)
[article]
Titre : Visualization analysis of resin flow behavior around a flow front using a rotary runner exchange system Type de document : texte imprimé Auteurs : Y. Kanetoh, Auteur ; H. Yokoi, Auteur Année de publication : 2012 Article en page(s) : p. 310-317 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Ecoulement visqueux
Fluides, Mécanique des
Matières plastiques -- Moulage par injection -- Appareils et matériel
Moulage par injection -- Défauts
Moules d'injection
PolystyrèneIndex. décimale : 668.4 Plastiques, vinyles Résumé : In plastic injection molding, external defects such as flow marks are serious problems. These external defects are known to occur during cavity filling processes inside the mold, and are closely related to resin flow behavior in the flow front area. In this study, the authors propose a new method for visualizing in-mold resin flow behavior using a glass-inserted mold and rotary runner exchange system capable of instantaneously switching two types of melt at the runner just before the gate. This method is capable not only of dynamic visualization, but also static visualization by the observation of cross-sections of a sample, because colored resins switched multiple times at the gate spread in layers inside the sample and freeze. Using this method and general purpose polystyrene, visualization analysis of the flow behavior of inner layer resins near the flow front in simple rectangular cavities was carried out. As a result, it was found that resins reaching the flow front are not exposed at the molded product surface immediately after the fountain-flow process, but remain along the circumference of the flow front for a long period of time, and then stretch out into a thin filmlike shape to form the surface of the molded product. In addition, the inner layer resins near the flow front form a converging flow just before reaching the flow front and then form a fountain flow. It was also confirmed that this is a general phenomenon in the fountain-flow process during injection molding regardless of whether the resin is crystalline or noncrystalline. Based on these results, we built a model on the flow of inner layer resins near the flow front of general resins. DOI : 10.3139/217.2457 En ligne : https://drive.google.com/file/d/12C-9v6b6ma__sKVLqopueoqxp7OW7vvm/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=15576
in INTERNATIONAL POLYMER PROCESSING > Vol. XXVII, N° 3 (07/2012) . - p. 310-317[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 13995 - Périodique Bibliothèque principale Documentaires Disponible A welcome extension of service life / F. Stephan Auch in KUNSTSTOFFE INTERNATIONAL, Vol. 101, N° 4 (04/2011)
[article]
Titre : A welcome extension of service life Type de document : texte imprimé Auteurs : F. Stephan Auch, Auteur Année de publication : 2011 Article en page(s) : p. 13-14 Langues : Anglais (eng) Catégories : Matières plastiques -- Moulage par injection -- Appareils et matériel Tags : 'Moulage injection' 'Changement moule' 'Fixation magnétique' Index. décimale : 668.4 Plastiques, vinyles Résumé : Rapid Mold Exchanges - Koziol, a manufacturer of high-quality designer plastic products, was able to extend the service lives of eleven injection molding machines by several hours when it introduced magnetic clamping. This was because the universal quick-change system reduced the time for exchanging molds by about 75 %. Note de contenu : - Over 500 products and just as many colors
- The concentration effect of long-pole technology
- 500 hours free capacity from nothingPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=11756
in KUNSTSTOFFE INTERNATIONAL > Vol. 101, N° 4 (04/2011) . - p. 13-14[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 013016 - Périodique Bibliothèque principale Documentaires Disponible What can you do at fall fairtime, when there aren't any ? / Clemens Doriat in KUNSTSTOFFE INTERNATIONAL, Vol. 110, N° 10 (2020)
PermalinkWhen efficiency potentials remain unused due to uncertainty / Felix A. Heinzler in KUNSTSTOFFE INTERNATIONAL, Vol. 102, N° 6 (06/2012)
Permalink