Accueil
Catégories
> Biomatériaux
BiomatériauxVoir aussi
|
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Bio-based algae oil : an oxidation and structural analysis / H. Birjandi Nejad in INTERNATIONAL JOURNAL OF COSMETIC SCIENCE, Vol. 42, N° 3 (06/2020)
[article]
Titre : Bio-based algae oil : an oxidation and structural analysis Type de document : document électronique Auteurs : H. Birjandi Nejad, Auteur ; Laurent Blasco, Auteur ; B. Moran, Auteur ; Juan Cebrià n, Auteur ; J. Woodger, Auteur ; E. Gonzalez, Auteur ; C. Pritts, Auteur ; J. Milligan, Auteur Année de publication : 2020 Article en page(s) : p. 237-247 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Algues
Biomatériaux
Biotechnologie
Chimie analytique
Emollients
Fermentation
Huiles et graisses végétales
Hydratation
Ingrédients cosmétiques
Peau -- Soins et hygiène
TriglycéridesIndex. décimale : 668.5 Parfums et cosmétiques Résumé : - Objective : In search of natural components, vegetal oils are increasingly becoming more popular in cosmetics. However, high oxidation instability, presence of potential allergens and synthetic anti-oxidants have limited their applications so far. Therefore, a need exists for a natural emollient with high oxidation stability. In this work, we report on a novel sustainably produced triglyceride containing primarily three monounsaturated oleic acid chains, dubbed ‘Bio-Based Algae Oil' hereafter, as a natural emollient for cosmetic formulations. To produce Bio-Based Algae Oil, simple sugars are converted into triglyceride oils using microalgae fermentation with minimal environmental impact.
- Methods : Bio-Based Algae Oil was compared to other commonly used triglyceride-based emollients in the skincare industry in terms of thermal/oxidation stability, composition and moisturizing properties. Oxidation stability of emollients was compared using Rancimat and pressurized differential scanning calorimetry (PDSC) techniques. Fatty acid composition of each oil was analysed using proton nuclear magnetic resonance (1H-NMR) and gas chromatography (GC) techniques to correlate unsaturation level of each oil to its oxidation stability. We also conducted an in vivo moisturizing study in which skin hydration level of human subjects was compared before and after application of emollient up to 24 h.
- Results : Results showed that Bio-Based Algae Oil was the most stable emollient in thermal and oxidation stability studies given its low unsaturation and high anti-oxidant content determined by 1H-NMR and GC techniques. It also provided the highest skin hydration level when applied on skin demonstrating its efficacy as a moisturizing emollient in cosmetic formulations.
- Conclusions : Compositional analysis of Bio-Based Algae revealed that it is a triglyceride containing primarily three monounsaturated oleic acid chains with very low polyunsaturated fatty acid content resulting in high oxidation stability and consequently prolonged shelf-life. Given its sustainability, high oxidation stability and skin health benefits such as moisturization demonstrated during an in vivo study, we envision to utilize Bio-Based Algae Oil in many cosmetic formulations across skincare, suncare and bath and shower markets.Note de contenu : - EXPERIMENTAL SECTION : Materials - Thermal stability - Structural analysis - Moisturizing study
- RESULTS AND DISCUSSION : Thermal stability - Oxidation stability - Structural analysis - Moisturizing study
- Table 1 : Onset of weight loss temperature (°C) of bio-based algae oil, synthetic triolein, sunflower oil and olive oil recorded via thermogravimetric analysis (TGA)
- Table 2 : Weight loss (%) of Bio-based algae oil, Synthetic Triolein, Sun-flower oil and olive oil recorded via isothermal thermogravimetric analysis (TGA) at 100, 130, 155 and 180°C
- Table 3 : Oxidation induction time (OIT) of bio-based algae oil, synthetic triolein, sunflower oil and olive oil measured by PDSC and rancimat techniques
- Table 4 : Rancimat oxidation induction time (OIT) of bo-based algae oil, synthetic triolein, sunflower oil and olive oil, extrapolated to 25°C
- Table 5 : Fatty acid profiles of bio-based algae oil, synthetic triolein, sunflower oil and olive oil
- Table 6 : Anti-oxidant content of bio-based algae oil, synthetic triolein, sunflower oil and olive oilDOI : https://doi.org/10.1111/ics.12606 En ligne : https://drive.google.com/file/d/1NQLKjwtTxsT7w09oEFddU9gi56uTvhjn/view?usp=shari [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=35271
in INTERNATIONAL JOURNAL OF COSMETIC SCIENCE > Vol. 42, N° 3 (06/2020) . - p. 237-247[article]A bio-based alternative for metal coatings / Christina Gabriel-Liebs in EUROPEAN COATINGS JOURNAL (ECJ), N° 11 (11/2022)
[article]
Titre : A bio-based alternative for metal coatings : Customised starch ester binders as a film former with optimised barrier properties Type de document : texte imprimé Auteurs : Christina Gabriel-Liebs, Auteur ; Jens Buller, Auteur ; Matthias Wanner, Auteur ; Katarzyna Krawczyk, Auteur Année de publication : 2022 Article en page(s) : p. 22-27 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Amidons
Bioadditifs
Biomatériaux
Essai de dureté
Esters -- Synthèse
Liants
Matériaux filmogènes
Ressources renouvelables
Revêtements -- Additifs
Revêtements organiquesIndex. décimale : 667.9 Revêtements et enduits Résumé : Bio-based coatings are in demand as never before. However, the hydrophilicity of bio-based raw materials, in particular, hinders their use as binders in coatings, and native starch shows the typical disadvantages of renewable resources. One way to overcome these obstacles is by modifying starch to de¬graded higher substituted starch esters. This class also shows potential for metal coatings. Note de contenu : - Experimental
- Synthesis of fatty acid esters of starch (FASE)
- Viscosity increases with increasing molecular weight
- Short starch chains generate higher hardness
- Water uptake reversibility (WUR) correlates with hardness
- Optimisation of barrier properties
- Table 1 : Synthesised starch esters with degrees of substitution (DS) from elemental analysis (EA), Mw of the corresponding degraded starch and the maxiumm suitable solids contents in Me-THF
- Table 2 : Results of Martens hardness (HM) testing
- Table 3 : Water uptake reversibility results and ranking of the Martens hardness results
- Table 4 : Low frequency Zmod data and ranking of WUR and the Martens hardness resultsEn ligne : https://drive.google.com/file/d/1PNYH3TYo7wBxD9ODODgWgiIk5sdXHQ2q/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=38352
in EUROPEAN COATINGS JOURNAL (ECJ) > N° 11 (11/2022) . - p. 22-27[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 23710 - Périodique Bibliothèque principale Documentaires Disponible Bio-based antimicrobial food packaging coatings / Brittney M. Mclnnis in COATINGS TECH, Vol. 15, N° 9 (09/2018)
[article]
Titre : Bio-based antimicrobial food packaging coatings Type de document : texte imprimé Auteurs : Brittney M. Mclnnis, Auteur ; Tyler W. Hodges, Auteur ; Lisa K. Kemp, Auteur ; Jonathan D. Hurt, Auteur ; Steve McDaniel, Auteur Année de publication : 2018 Article en page(s) : p. 36-43 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Alcool polyvinylique
Aliments -- Emballages -- Aspect sanitaire
Antimicrobiens
Bioadditifs
Biomatériaux
ChitosaneLe chitosane ou chitosan est un polyoside composé de la distribution aléatoire de D-glucosamine liée en ß-(1-4) (unité désacétylée) et de N-acétyl-D-glucosamine (unité acétylée). Il est produit par désacétylation chimique (en milieu alcalin) ou enzymatique de la chitine, le composant de l'exosquelette des arthropodes (crustacés) ou de l'endosquelette des céphalopodes (calmars...) ou encore de la paroi des champignons. Cette matière première est déminéralisée par traitement à l'acide chlorhydrique, puis déprotéinée en présence de soude ou de potasse et enfin décolorée grâce à un agent oxydant. Le degré d'acétylation (DA) est le pourcentage d'unités acétylées par rapport au nombre d'unités totales, il peut être déterminé par spectroscopie infrarouge à transformée de Fourier (IR-TF) ou par un titrage par une base forte. La frontière entre chitosane et chitine correspond à un DA de 50 % : en deçà le composé est nommé chitosane, au-delà , chitine. Le chitosane est soluble en milieu acide contrairement à la chitine qui est insoluble. Il est important de faire la distinction entre le degré d'acétylation (DA) et le degré de déacétylation (DD). L'un étant l'inverse de l'autre c'est-à -dire que du chitosane ayant un DD de 85 %, possède 15 % de groupements acétyles et 85 % de groupements amines sur ses chaînes.
Le chitosane est biodégradable et biocompatible (notamment hémocompatible). Il est également bactériostatique et fongistatique.
Le chitosane est également utilisé pour le traitement des eaux usées par filtration ainsi que dans divers domaines comme la cosmétique, la diététique et la médecine.
Emballages en matières plastiques
Evaluation
Peptides
Revêtements -- Additifs
Revêtements -- Analyse
Tests microbiologiquesIndex. décimale : 667.9 Revêtements et enduits Résumé : The antimicrobial properties of two disparate bio-based coating additives were evaluated in a polyvinyl alcohol (PVA) food packaging coating for antimicrobial activity. Chitosan, a shrimp and crustacean shell derived polysaccharide, and an antimicrobial peptide were evaluated in a dissolvable food package coating for reductions in microbial growth after contacting agar patties serving as food simulants. Where the antimicrobial components of such packaging coatings are chosen to be generally recognized as safe by worldwide regulatory agencies, migration from the packaging into headspaces and food-contact surfaces can provide enhanced efficacy against foodborne pathogens, including viruses. The techniques and coatings presented in this article suggest that dramatic improvements in food safety can be achieved using coatings containing non-toxic bio-based biocides. Note de contenu : - MATERIALS AND METHODS : Reagents and bacterial strains - Preparation of coated films - Antimicrobial coated disk treatment of E. coli contaminated agar plates - Preparation of vacuum-sealed food simulants
- EXPERIMENTS AND RESULTS : Clear disk antimicrobial assay - Moist-food simulant packaging study - Commercial packaging study at elevated concentrations and reduced coating thickness
- Table 1 : Examples of recent outbreaks of foodborne illness in the United states
- Table 2 : Colony counts and percent growth inhibition data for the high concentration PVA/chitosan/AMP7 on opalen and trayforma surfaces
- Fig. 1 : Clear disk antimicrobial assays were done to rapidly determine synergistic, additive, or antagonistic effects of the studied bio-based antimicrobial agents
- Fig. 2 : Vacuum sealed food-simulant packaging system having a bio-based antimicrobial coating. Diagram of the food-simulant packaging assembly, and a photograph of a fully assembled vacuum-sealed packaged food-simulant contamined with bacteria
- Fig. 3 : Representative bacterial colony growth results upon contact with coated disks having increasing concentrations of AMP7 and/or chitosan (each test done in triplicate). Each bacterial colony that survived under the coated disk appears as a yellow dot in that area of the plate, while nearl complete-bacterial growth covers regions outside the disk
- Fig. 4 : Dose responses of chitosan and AMP7, individually and in combination. The percent growth inhibition (as determined by reduced colony counts compared to PVA negative control) was used to calculate the dose response to coatings dosed with varying concentrations of AMP7 (A) and chitosan (B). A heatmap shows the response (as percent growth inhibition) to numerous combinations of different concentrations of AMP7 and chitosan (C). A contour map of synergy scores of the AMP7 and chitosan combinations, determined using the ZIP method, by which the positive scores (red) indicate synergy, the negative scores (green) indicate antagonism, and zero scores (white) indicate additive responses (D)
- Fig. 5 : Resutts for vacuum-sealed bags containing PVA coatings dosed with AMP7 and chitosan combinations. Table of the colonycounts and percent growth inhibition data for vacuum-sealed samples treated with combination of chitosan and AMP7 in the coatings (Al. These data were used to calculate synergy scores using the Bliss model, which are visualized in a contour plot (B)
- Fig. 6 : Antagonistic response confirmed with vacuum-sealed hag agar patty studies (each sample tested in triplicate)
- Fig. 7 : Images of the vacuum-sealed agar pathos for the plain, uncoated films (WH column) and bio-based antimicrobial containing samples with 0.2-mil thick coating (middle column) 010.6-mil thick coating (right column)En ligne : https://drive.google.com/file/d/1DV-OBIZ8Ggr0Z9ILRvMRZIkqah-iNmWZ/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=31235
in COATINGS TECH > Vol. 15, N° 9 (09/2018) . - p. 36-43[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 20272 - Périodique Bibliothèque principale Documentaires Disponible Bio-based carbon fibers - efforts and prospects / Hans-Peter Fink in CHEMICAL FIBERS INTERNATIONAL, Vol. 63, N° 1 (03/2013)
[article]
Titre : Bio-based carbon fibers - efforts and prospects Type de document : texte imprimé Auteurs : Hans-Peter Fink, Auteur ; André Lehmann, Auteur ; Johannes Ganster, Auteur Année de publication : 2013 Article en page(s) : p. 29-30 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Biomatériaux
Fibres de carbone
LignineLa lignine est un des principaux composants du bois, avec la cellulose, l'hémicellulose et des matières extractibles. La lignine est présente principalement dans les plantes vasculaires et dans quelques algues. Ses principales fonctions sont d'apporter de la rigidité, une imperméabilité à l'eau et une grande résistance à la décomposition. Toutes les plantes vasculaires, ligneuses et herbacées, fabriquent de la lignine. Quantitativement, la teneur en lignine est de 3 à 5 % dans les feuilles, 5 à 20 % dans les tiges herbacées, 15 à 35 % dans les tiges ligneuses. Elle est moindre pour les plantes annuelles que pour les vivaces, elle est maximum chez les arbres. La lignine est principalement localisée entre les cellules (voir parois pectocellulosiques), mais on en trouve une quantité significative à l'intérieur même de celles-ci. Bien que la lignine soit un réseau tridimensionnel hydrophobe complexe, l'unité de base se résume essentiellement à une unité de phénylpropane. La lignine est le deuxième biopolymère renouvelable le plus abondant sur la Terre, après la cellulose, et, à elles deux, elles cumulent plus de 70 % de la biomasse totale. C'est pourquoi elle fait l'objet de recherches en vue de valorisations autres que ses utilisations actuelles en bois d'œuvre et en combustible.
Voie de biosynthèse : La lignine est une molécule dont le précurseur est la phénylalanine. Cet acide aminé va subir une cascade de réactions faisant intervenir une dizaine de familles d'enzymes différentes afin de former des monolignols. Ces enzymes sont : phénylalanine ammonia-lyase (PAL), cinnamate 4-hydroxylase (C4H), 4-coumarate:CoA ligase (4CL), hydroxycinnamoyl-CoA shikimate/quinate hydroxycinnamoyl transferase (HCT), p-coumarate 3-hydroxylase (C3H), caffeoyl-CoA o-methyltransferase (CCoAOMT), cinnamoyl-CoA reductase (CCR), ferrulate 5-hydroxylase (F5H), caffeic acid O-methyltransferase (COMT) et cinnamyl alcohol deshydrogenase (CAD). Dans un certain nombre de cas, des aldéhydes peuvent également être incorporés dans le polymère.Index. décimale : 677.4 Textiles artificiels Résumé : No other material provides better mechanical properties for lightweight constructions (automotive industry - especially electro cars, wind turbine blades, sporting goods, etc.) than carbon fibers. Carbon fibers are filament yarns with a carbon content of more than 90%, tow sizes between 2-24K (small tow) and 48 to 320k (large tow) and filament radii between 5-7 µm. By a slow heat treatment of an organic precursor fiber, starting from e.g. 200°C up to temperatures of 2,500°C (in special cases 3000°C) a special arrangement of stacks of hexagonal carbon layers oriented along the fiber direction if sormed. This sometimes called turbostatic structure allows maximum stiffness combined with high strength and low density in the range of 1.76-2.15 g/cm3. Note de contenu : - Fiber reinforcement
- Carbon fiber precursors
- Lignin
- Carbon fibers made from ligninEn ligne : https://drive.google.com/file/d/1aLpHO357jerk76YCPGJS1YyGadacJxU7/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=18296
in CHEMICAL FIBERS INTERNATIONAL > Vol. 63, N° 1 (03/2013) . - p. 29-30[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 14982 - Périodique Bibliothèque principale Documentaires Disponible Bio-based carbon fibers - efforts and prospects / Hans-Peter Fink in CHEMICAL FIBERS INTERNATIONAL, (10/2013)
[article]
Titre : Bio-based carbon fibers - efforts and prospects Type de document : texte imprimé Auteurs : Hans-Peter Fink, Auteur ; André Lehmann, Auteur ; Johannes Ganster, Auteur Année de publication : 2013 Article en page(s) : p. 44-45 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Biomatériaux
Biopolymères
Fibres de carbone
LignineLa lignine est un des principaux composants du bois, avec la cellulose, l'hémicellulose et des matières extractibles. La lignine est présente principalement dans les plantes vasculaires et dans quelques algues. Ses principales fonctions sont d'apporter de la rigidité, une imperméabilité à l'eau et une grande résistance à la décomposition. Toutes les plantes vasculaires, ligneuses et herbacées, fabriquent de la lignine. Quantitativement, la teneur en lignine est de 3 à 5 % dans les feuilles, 5 à 20 % dans les tiges herbacées, 15 à 35 % dans les tiges ligneuses. Elle est moindre pour les plantes annuelles que pour les vivaces, elle est maximum chez les arbres. La lignine est principalement localisée entre les cellules (voir parois pectocellulosiques), mais on en trouve une quantité significative à l'intérieur même de celles-ci. Bien que la lignine soit un réseau tridimensionnel hydrophobe complexe, l'unité de base se résume essentiellement à une unité de phénylpropane. La lignine est le deuxième biopolymère renouvelable le plus abondant sur la Terre, après la cellulose, et, à elles deux, elles cumulent plus de 70 % de la biomasse totale. C'est pourquoi elle fait l'objet de recherches en vue de valorisations autres que ses utilisations actuelles en bois d'œuvre et en combustible.
Voie de biosynthèse : La lignine est une molécule dont le précurseur est la phénylalanine. Cet acide aminé va subir une cascade de réactions faisant intervenir une dizaine de familles d'enzymes différentes afin de former des monolignols. Ces enzymes sont : phénylalanine ammonia-lyase (PAL), cinnamate 4-hydroxylase (C4H), 4-coumarate:CoA ligase (4CL), hydroxycinnamoyl-CoA shikimate/quinate hydroxycinnamoyl transferase (HCT), p-coumarate 3-hydroxylase (C3H), caffeoyl-CoA o-methyltransferase (CCoAOMT), cinnamoyl-CoA reductase (CCR), ferrulate 5-hydroxylase (F5H), caffeic acid O-methyltransferase (COMT) et cinnamyl alcohol deshydrogenase (CAD). Dans un certain nombre de cas, des aldéhydes peuvent également être incorporés dans le polymère.Index. décimale : 677.4 Textiles artificiels Résumé : No other material provides better mechanical properties for lightweight constructions (automotive industry — especially electro cars, wind turbine blades, sporting goods, etc.) than carbon fibers. Carbon fibers are filament yarns with a carbon content of more than 90 %, tow sizes between 2-24k (small tow) and 48 to 320k (large tow) and filament radii between 5-7 pm. By a slow heat treatment of an organic precursor fiber, starting from e.g. 200 °C up to temperatures of 2,500 °C (in special cases 3,000 °C) a special arrange-ment of stacks of hexagonal carbon layers oriented along the fiber direction is formed (Fig. 1). This, sometimes called turbostratic structure allows maximum stiffness com-bined with high strength and low density in the range of 1.76-2.15 g/cm3. Note de contenu : - Fibre reinforcement
- Carbon fiber precursors
- Lignin
- Carbon fibers made from lignin
- Fig. 1 : Turbostratic carbon fiber structure showing the arrangement of graphite planes, fiber axis vertical
- Fig. 2 : Specific strength and modulus of various high performance fibers
- Fig. 3 : Phenylpropane monomers of ligninEn ligne : https://drive.google.com/file/d/1e9qXR73z1jskn8YqT-g4Us19JeDvxdqr/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=19768
in CHEMICAL FIBERS INTERNATIONAL > (10/2013) . - p. 44-45[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 15619 - Périodique Bibliothèque principale Documentaires Disponible PermalinkBio-based composites for high-performance materials / Wirasak Smitthipong / Boca Raton [Etats-Unis] : CRC Press - Taylor Francis Group (2015)
PermalinkBio-based fibers in oil spill cleanups / Subramonia Pillai Viju in CHEMICAL FIBERS INTERNATIONAL, (10/2021)
PermalinkBio-based fibers with improved properties for apparel / Nuria Lopez Aznar in CHEMICAL FIBERS INTERNATIONAL, Vol. 68, N° 4 (12/2018)
PermalinkBio-based hybrid fibers with reduced flammability / Ingo Bernt in TECHNICAL TEXTILES, Vol. 65, N° 5 (12/2022)
PermalinkBio-based polyols for high-performance polyurethane adhesives in ADHESIVES & SEALANTS INDUSTRY (ASI), Vol. 21, N° 5 (05/2014)
PermalinkBio-based preservation of home care formulations with lactic acid / Katja von Nessen in SOFW JOURNAL, Vol. 146, N° 5 (05/2020)
PermalinkBio-based pultruded profiles including graphene for building envelopes / Sergio Fita in JEC COMPOSITES MAGAZINE, N° 101 (11-12/2015)
PermalinkBio-based reactive diluent derived from cardanol and its application in polyurethane acrylate (PUA) coatings with high performance / Yun Hu in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 16, N° 2 (03/2019)
PermalinkBio-based succinic acid polyester polyols / William D. Coggio in ADHESIVES & SEALANTS INDUSTRY (ASI), Vol. 22, N° 6 (06/2015)
PermalinkPermalinkBio-coatings improve implant functionality in ADHESIVES & SEALANTS INDUSTRY (ASI), Vol. 20, N° 9 (09/2013)
PermalinkBio-sourced sandwich materials for marine applications / Ludo Bosser in JEC COMPOSITES MAGAZINE, N° 75 (08-09/2012)
PermalinkPermalinkBiobased films prepared from collagen solutions derived from un-tanned hides / Cheng-Kung Liu in JOURNAL OF THE AMERICAN LEATHER CHEMISTS ASSOCIATION (JALCA), Vol. CX, N° 2 (02/2015)
Permalink