Accueil
Catégories
> Polycarbonates
PolycarbonatesVoir aussi
|
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Corrélations entre analyses physico-chimiques et analyses mécaniques des propriétés adhésives du polycarbonate / L. Gresser in LES CAHIERS DE RHEOLOGIE, Vol. XVI, N° 1 (10/1998)
[article]
Titre : Corrélations entre analyses physico-chimiques et analyses mécaniques des propriétés adhésives du polycarbonate Type de document : texte imprimé Auteurs : L. Gresser, Auteur ; F. X. Gibert, Auteur ; R. Peyrous, Auteur ; B. Held, Auteur Année de publication : 1998 Article en page(s) : p. 65-70 Note générale : Bibliogr. Langues : Français (fre) Catégories : Polycarbonates
Potentiel zeta
Rhéologie
Surfaces -- Propriétés adhésives
TackIndex. décimale : 532.05 Mécanique des fluides et des liquides - Dynamique (cinétique et cinématique) Résumé : Nous avons étudié l'influence des paramètres expérimentaux d'une décharge couronne de type fil-plan sur les propriétés adhésives de surfaces de polycarbonates. Les effets ont été caractérisés par deux méthodes, une physico-chimique, la mesure du potentiel zêta, et l'autre rhéologique, la mesure du tack. La première rend compte des propriétés acido-basiques de la surface tandis que la seconde renseigne sur les propriétés adhésives. Nous pouvons ainsi corréler ces deux méthodes afin de rendre compte de l'efficacité des traitements. Le gaz utilisé étant l'oxygène, nous avons constaté une acidification de la surface plus ou moins prononcée suivant les paramètres expérimentaux Cet effet est ensuite visualisé à partir des courbes obtenues en tack où les interactions de surface sont primordiales et où nous constatons une baisse de l'énergie d'adhésion polycarbonate-colle. Note de contenu : - Considérations théoriques
- Dispositifs expérimentaux
- RésultatsPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=36449
in LES CAHIERS DE RHEOLOGIE > Vol. XVI, N° 1 (10/1998) . - p. 65-70[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21932 - Colloque, congrès, etc. Bibliothèque principale Documentaires Disponible Custom interior design / Roland Künzel in KUNSTSTOFFE INTERNATIONAL, Vol. 101, N° 3 (03/2011)
[article]
Titre : Custom interior design Type de document : texte imprimé Auteurs : Roland Künzel, Auteur ; Dirk W. Pophusen, Auteur Année de publication : 2011 Article en page(s) : p. 51-54 Langues : Anglais (eng) Catégories : Automobiles -- Habitacles
Design industriel
Films plastiques
Matières plastiques dans les automobiles
PolycarbonatesIndex. décimale : 668.4 Plastiques, vinyles Résumé : Polycarbonate Film - New tasks lie ahead for polycarbonate films inside vehicles. The latest design ideas aim to create in the car interior a personalized, stylish ambience that creates a good atmosphere and offers high levels of comfort. This calls for large parts featuring numerous integrated functions and a flowing, intact surface characterized by depth of gloss. Note de contenu : - Decoration or large, homogeneous, all-in-one surfaces
- Precision shaping of large formats
- Highly integrated center console, thanks to advanced technologies
- Diffuser and reflection film for displaysPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=11749
in KUNSTSTOFFE INTERNATIONAL > Vol. 101, N° 3 (03/2011) . - p. 51-54[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 012938 - Périodique Bibliothèque principale Documentaires Disponible Customized soft-touch thanks to threefold process integration in KUNSTSTOFFE INTERNATIONAL, Vol. 104, N° 3 (03/2014)
[article]
Titre : Customized soft-touch thanks to threefold process integration Type de document : texte imprimé Année de publication : 2014 Article en page(s) : p. 36-38 Langues : Anglais (eng) Catégories : Automobiles -- Habitacles
Mousses plastiques
Polycarbonates
Polyuréthanes
Production
Terpolymère acrylonitrile butadiène styrène
Thermoplastique Oléfinique (élastomère)
Toucher softIndex. décimale : 668.4 Plastiques, vinyles Résumé : Vehicle interior - Progress in the so-called "Varysoft" process gives manufacturers and users of soft-touch components new horizons thanks to the swivel-plate tool that is employed. As a flexible and economic manufacturing process, the revamped process now allows softer parts with relatively thick foam layers and both tactilely and optically high-quality surfaces to be produced. Note de contenu : - The trigger for an improved process concept
- The mold concept - an absolute innovation
- The system operates at two levels
- Parallel process sequencesEn ligne : https://drive.google.com/file/d/10-xmw2FcQWER1OXojYm1g8DhLC6X_pij/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=20840
in KUNSTSTOFFE INTERNATIONAL > Vol. 104, N° 3 (03/2014) . - p. 36-38[article]Réservation
Réserver ce document
Exemplaires (3)
Code-barres Cote Support Localisation Section Disponibilité 16126 - Périodique Bibliothèque principale Documentaires Disponible 16206 - Périodique Bibliothèque principale Documentaires Disponible 16207 - Périodique Bibliothèque principale Documentaires Disponible Damping, thermal and mechanical analyses of polycarbonate/cerium oxide composites for structural applications / R. Karuppasamy in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 3 (07/2019)
[article]
Titre : Damping, thermal and mechanical analyses of polycarbonate/cerium oxide composites for structural applications Type de document : texte imprimé Auteurs : R. Karuppasamy, Auteur ; R. Muralikannan, Auteur Année de publication : 2019 Article en page(s) : p. 324-329 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Amortissement (mécanique)
Analyse mécanique dynamique
Analyse thermique
Caractérisation
Composites thermoplastiques -- Propriétés mécaniques
Essais de résilience
Matières plastiques -- Extrusion
Oxyde de cérium
Polycarbonates
Résistance à la traction
Résistance au chocs
ThermogravimétrieIndex. décimale : 668.4 Plastiques, vinyles Résumé : Polycarbonate (PC)/cerium (IV) oxide (CeO2) composites are prepared by a melt-compounding method using a twin-screw extruder. The effect of the CeO2 content on the damping property of the composites was investigated using scanning electron microscopy, dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). In addition, the composites' mechanical properties were studied through tensile and impact tests. The DMA results revealed that the addition of CeO2 (0.5 wt%) improved the damping property of the composite. TGA showed that the thermal stability was improved when the CeO2 became 1 wt%. Mechanical tests revealed that both the tensile and impact strengths were substantially improved when 1 wt% CeO2 was added. Finally, it can be concluded that the 0.5 wt% CeO2-filled PC composite can be used as a structural damping material. Note de contenu : - EXPERIMENTAL : Materials - Composite preparation - Characterization
- RESULTS AND DISCUSSION : DMA - Tensile strength analysis
- Impact strength analysis - Thermogravimetric analysis - Morphologies of the fractured surfacesDOI : https://doi.org/10.3139/217.3723 En ligne : https://drive.google.com/file/d/1v_AkaLdOZrn65-ueVXTdiSCqQp0BQ9St/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=32894
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 3 (07/2019) . - p. 324-329[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21036 - Périodique Bibliothèque principale Documentaires Disponible Défauts d'aspect des pièces injectées / Marie-France Lacrampe in CAOUTCHOUCS & PLASTIQUES, N° 797 (09/2001)
[article]
Titre : Défauts d'aspect des pièces injectées Type de document : texte imprimé Auteurs : Marie-France Lacrampe, Auteur ; J. Pabiot, Auteur Année de publication : 2001 Article en page(s) : p. 30-37 Note générale : Bibliogr. Langues : Français (fre) Catégories : Agent mattant
Alliages polymères
Bisphénol A
Copolymère éthylène propylène
Matières plastiques -- Défauts
Moulage par injection -- Défauts
Polycarbonates
Polyéthylène basse densité linéaire
Polyéthylène haute densité
Polypropylène
Rhéologie
Surfaces -- Analyse
Terpolymère acrylonitrile butadiène styrène
Terpolymère acrylonitrile styrène acrylate
ThermoplastiquesUne matière thermoplastique désigne une matière qui se ramollit (parfois on observe une fusion franche) d'une façon répétée lorsqu'elle est chauffée au-dessus d'une certaine température, mais qui, au-dessous, redevient dure. Une telle matière conservera donc toujours de manière réversible sa thermoplasticité initiale. Cette qualité rend le matériau thermoplastique potentiellement recyclable (après broyage). Cela implique que la matière ramollie ne soit pas thermiquement dégradée et que les contraintes mécaniques de cisaillement introduites par un procédé de mise en forme ne modifient pas la structure moléculaire.Index. décimale : 668.4 Plastiques, vinyles Résumé : Le point sur un certain nombre de défauts d'aspect de surface affectant les pièces injectées en polymères thermoplastiques. Un critère primordial dans l'univers du secteur automobile. Note de contenu : - Types de défauts observés
- PARAMÈTRES D'INFLUENCE : Incidence de la géométrie de la pièce - Incidence des paramètres d'injection - Incidence de la nature et des propriétés du polymère
- MÉCANISMES DE GÉNÉRATION SUPPOSÉSPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=23919
in CAOUTCHOUCS & PLASTIQUES > N° 797 (09/2001) . - p. 30-37[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 000811 - Périodique Bibliothèque principale Documentaires Disponible Designing for electromobility / Roland Brambrink in KUNSTSTOFFE INTERNATIONAL, Vol. 109, N° 3 (03/2019)
PermalinkDevelopment of an immiscible polymer/polymer/nanoparticle system to assess the location of nanoparticles by quantitative optical microscopy / L. H. B. Johansen in INTERNATIONAL POLYMER PROCESSING, Vol. XXXI, N° 5 (11/2016)
PermalinkDevelopments in waterborne thermal insulation coatings / Sudhir Achar in JOURNAL OF PROTECTIVE COATINGS & LININGS (JPCL), Vol. 30, N° 3 (03/2013)
PermalinkLe dioxyde de carbone : une matière première pour l'industrie chimique / Michael Röper in L'ACTUALITE CHIMIQUE, N° 371-372 (02-03/2013)
PermalinkDirect imprinting using magnetic nickel mold and electromagnetism assisted pressure for replication of microstructures / Y.-J. Weng in INTERNATIONAL POLYMER PROCESSING, Vol. XXVI, N° 5 (11/2011)
PermalinkEco-friendly fire prevention / Rudolf Pfaendner in KUNSTSTOFFE INTERNATIONAL, Vol. 104, N° 8 (08/2014)
PermalinkEffect of repeated sterilization / Miriam Haerst in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 2 (02/2013)
PermalinkEffect of screw rotation speed on the properties of polycarbonate/vapor-grown carbon fiber composites prepared by melt compounding / Shuichi Tanoue in INTERNATIONAL POLYMER PROCESSING, Vol. XXIX, N° 1 (03/2014)
PermalinkEffects of injection molding holding pressure on the replication of surface microfeatures / T. R. Tofteberg in INTERNATIONAL POLYMER PROCESSING, Vol. XXV, N° 3 (07/2010)
PermalinkEffects of surface fluorination on the dyeing of polycarbonate (PC) resin / Jae-Ho Kim in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 19, N° 2 (03/2022)
PermalinkEfficient production of thick-walled parts / Christian Maier in KUNSTSTOFFE INTERNATIONAL, Vol. 103, N° 9 (09/2013)
PermalinkEntering the third dimension with light-colored LDS additive / Markus Heidebrecht in KUNSTSTOFFE INTERNATIONAL, Vol. 107, N° 5 (05/2017)
PermalinkEtude des relations entre contrainte et orientation moléculaire au voisinage de Tg dans les polymères amorphes / Clarisse Luap in LES CAHIERS DE RHEOLOGIE, Vol. XI, N° 3-4 (10/1993)
PermalinkExperimental investigation of PC-films using optical measurements / Christian Dammann in INTERNATIONAL POLYMER PROCESSING, Vol. XXIX, N° 2 (05/2014)
PermalinkExploring the applicability of a simplified fully coupled flow/orientation algorithm developed for polymer composites extrusion deposition additive manufacturing / Zhaogui Wang in INTERNATIONAL POLYMER PROCESSING, Vol. 37, N° 1 (2022)
Permalink