Accueil
INTERNATIONAL POLYMER PROCESSING / Polymer Processing Society . Vol. XXXIV, N° 4Mention de date : 08/2019Paru le : 27/08/2019 |
Dépouillements
Ajouter le résultat dans votre panierInfluence of post-treatment media on morphological changes in transient macromolecules of polymeric fibers / Somayeh Baseri in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Influence of post-treatment media on morphological changes in transient macromolecules of polymeric fibers Type de document : texte imprimé Auteurs : Somayeh Baseri, Auteur Année de publication : 2019 Article en page(s) : p. 388-397 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Fibres textiles synthétiques
Matériaux -- Modifications chimiques
Polyesters
Solvants écologiquesIndex. décimale : 668.9 Polymères Résumé : There is a growing literature investigating the effects of thermal annealing and green solvent exposure on the microstructural changes, in general, and transient structures in polyester fibers, in particular, using such techniques as birefringence, differential scanning calorimetry, X-ray diffraction, and dynamic mechanical analysis. The results obtained from these studies consistently indicate that transient structures in polyester fibers strongly depend on the medium used so that treatment in different media produces important changes such as the transformation of the intermediate domain into an amorphous or crystalline region. Compared to polyester samples annealed at high temperatures over long treatment times, those exposed to green solvents yield higher values of crystallinity, orientation, density, transient structure, crystallite size in lateral directions, and elastic modulus but lower values of fractional free volume. Being environmentally friendly, green solvents may, thus, be considered as superior replacements for the conventional materials used in thermal annealing, especially because they change the fine structure of polyester fibers over shorter treatment times and at lower temperatures.
Note de contenu : - Development of transient structures in polyester fibers
- Transient structural changes induced by the green solvent
- Transient structural changes induced by thermal annealingDOI : 10.3139/217.3793 En ligne : https://www.degruyter.com/document/doi/10.3139/217.3793/pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33057
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 388-397[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible The influence of mechanical recycling on properties in injection molding of fiber-reinforced polypropylene / Tim Evens in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : The influence of mechanical recycling on properties in injection molding of fiber-reinforced polypropylene Type de document : texte imprimé Auteurs : Tim Evens, Auteur ; G.-J. Bex, Auteur ; M. Yigit, Auteur ; J. de Keyzer, Auteur ; F. Desplentere, Auteur ; A. van Bael, Auteur Année de publication : 2019 Article en page(s) : p. 398-407 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Composites à fibres -- Moulage par injection
Composites à fibres -- Propriétés mécaniques
Composites à fibres -- Recyclage
Composites à fibres courtes
Composites à fibres de carbone
Composites à fibres de verre
Composites à fibres végétales
Essais dynamiques
Lin et constituantsLe lin cultivé (Linum usitatissimum) est une plante annuelle de la famille des Linaceae cultivée principalement pour ses fibres, mais aussi pour ses graines oléagineuses. Les fibres du lin permettent de faire des cordes, du tissu (lin textile pour ses qualités anallergiques, isolantes et thermorégulateurs), ou plus récemment des charges isolantes pour des matériaux de construction. Les graines sont utilisées pour produire de l'huile de lin pour l'industrie de l'encre et de la peinture, pour la consommation humaine et animale, à cause de sa richesse en oméga 3.
Le lin est une des rares fibres textiles végétales européennes. Elle a comme caractéristiques la légereté, la rigidité et la résistance et comme particularité d'être une fibre longue (plusieurs dizaines de centimètres), par rapport aux fibres courtes (coton, chanvre) ou moyennes (laine).
Polypropylène
Résistance à la traction
Résistance au chocs
Rigidité (physique)Index. décimale : 668.4 Plastiques, vinyles Résumé : Due to higher mechanical demands on technical parts, the application of short fiber reinforced thermoplastics for injection molding is strongly increasing. Therefore, more attention needs to be paid to the optimization of their recycling processes. Mechanical shredding of thermoplastics into granules is a common recycling method within polymer industries. The breaking of polymer chains and reinforcing fibers during this process may affect the material properties. This study presents the effect of ten recycling sequences on four different materials: polypropylene, glass fiber filled polypropylene, carbon fiber filled polypropylene and flax fiber filled polypropylene. Tests indicate that recycling has a negative influence on most of the mechanical properties. Polypropylene without fibers forms an exception as it does not exhibit any significant change in material properties. Glass fiber and carbon fiber reinforced polypropylene show a decrease in stiffness and tensile strength during the recycling steps. The impact strength of carbon and flax fiber reinforced polypropylene increases whereas that of glass fiber reinforced polypropylene decreases. Note de contenu : - MATERIALS AND METHODS
- RESULTS AND DISCUSSION : Tensile strength - Flexural modulus - Impact strength - Stress-strain curve - Effect of recycling on the fiber length distribution - DiscussionDOI : 10.3139/217.3770 En ligne : https://www.degruyter.com/document/doi/10.3139/217.3770/pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33058
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 398-407[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible Study on influence of co-injection molding proces on self-reinforcing characteristics of self-reinforced polypropylene composite vis visualization / Kai-Yu Jiang in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Study on influence of co-injection molding proces on self-reinforcing characteristics of self-reinforced polypropylene composite vis visualization Type de document : texte imprimé Auteurs : Kai-Yu Jiang, Auteur ; Y. Zhang, Auteur ; L. Yang, Auteur ; Y. Lu, Auteur Année de publication : 2019 Article en page(s) : p. 408-415 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Composites à fibres -- Moulage par injection
Composites à fibres -- Propriétés mécaniques
Composites thermoplastiques auto-renforcés
PolypropylèneIndex. décimale : 668.4 Plastiques, vinyles Résumé : Self-reinforced polymer composites (SRCs), which are fabricated by combining the same type of polymer with different properties into one body, have high specific strength, no interfacial heterogeneity, and ease of recycling. To better understand the relationship between the molding process and mechanical properties of SRCs, the co-injection molding process was used in this study to process SRCs samples. Further, a self-developed visualized experimental device was used to observe the flow of the polymer melt directly during co-injection molding. From the visualization results, it was found that the tensile properties of SRCs are positively correlated with the absolute value of the slopes of the velocity change at lower melt temperature. When the melt temperature increases to a certain degree, the tensile properties of SRCs are much lower than that of lower melt temperature. The shear rate inside the melt flow and the shear rate between the melt and the matrix wall play a major role in the self-reinforcing characteristics of the SRC. Note de contenu : - MATERIALS AND METHODS : Specimen and materials - Molding equipment and processing parameters - Measuring mechanical properties
- RESULTS AND DISCUSSION : Mechanical properties of the SRC specimens - Vizualization results - Data contrast analysisEn ligne : https://drive.google.com/file/d/1oh9C1u47G2n626jbtdFGZHtl2vmA-Fok/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33059
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 408-415[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible Influence of ultrasonic transducer structural parameters on the frictional plasticizing heat generation of polymer particles / X. Li in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Influence of ultrasonic transducer structural parameters on the frictional plasticizing heat generation of polymer particles Type de document : texte imprimé Auteurs : X. Li, Auteur ; H.-G. Tian, Auteur ; W.-W. Zhang, Auteur ; S.-C. Zhang, Auteur Année de publication : 2019 Article en page(s) : p. 416–424 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Interfaces (Sciences physiques)
Matériaux piézoélectriques
Plastification
Thermocinétique
Transducteurs ultrasonores
UltrasonsIndex. décimale : 668.4 Plastiques, vinyles Résumé : This paper explores the influence of structural parameters of ultrasonic transducer on the frictional plasticizing heat generation of polymer particles. A three-dimensional model of the interfacial friction plasticizing heating was established, and a transducer with different structural parameters was designed and analyzed. The actual output longitudinal vibration excitation of the transducer obtained by simulation analysis was directly loaded into the heating model, which further investigated the effect of various structural parameters on the frictional plasticizing heating process and temperature distribution of polymer particles. The results demonstrated that the interfacial friction plasticizing heating temperature of polymer particles increases nonlinearly with the longitudinal vibration excitation time, and the heat generation is a transient process. The amplification ratio has the greatest influence on the interfacial friction plasticizing heating rates of polymer particles, followed by both front cover length and piezoelectric ceramic pieces thickness; the effects of length of rear cover, horn and ultrasonic tool head are the smallest. The present work provides an effective basis for further studying the ultrasonic plasticizing of polymer particles in ultrasonic micro-molding. Note de contenu : - SYSTEM COMPONENTS
- DESIGN AND SIMULATION ANALYSIS : Structure design - Modal and transient analysis
- SIMULATION METHOD : Theory of interfacial friction plasticizing heat generation - Model of interfacial friction plasticizing heating
- RESULTS AND DISCUSSION : Interfacial friction plasticizing heating process - Interfacial friction plasticizing heating rateDOI : 10.3139/217.3671 En ligne : https://drive.google.com/file/d/1fI-Ro8Zyf6k4l-7lJwBDnoGO13TDyxuk/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33060
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 416–424[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible Influence of the mold temperature and part thickness on the replication quality and molecular orientation in compression injection molding of polystyrene / Benedikt Roth in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Influence of the mold temperature and part thickness on the replication quality and molecular orientation in compression injection molding of polystyrene Type de document : texte imprimé Auteurs : Benedikt Roth, Auteur ; M.-Y. Zhou, Auteur ; Dietmar Drummer , Auteur Année de publication : 2019 Article en page(s) : p. 425-433 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Matières plastiques -- Moulage par compression
Moulage par injection-compression
Orientation moléculaire (matériaux)
Polystyrène
Température -- ContrôleIndex. décimale : 668.4 Plastiques, vinyles Résumé : It is well known that the process of injection molding with dynamic mold temperature control leads to a good replication quality of high aspect ratio microstructures. However, the inhomogeneous pressure distribution during the holding pressure phase results in an anisotropy of the component properties, low dimensional accuracy and, especially with optical polymers, in undesired stress birefringence. The anisotropy is based on the orientation of the molecular chains in the flow direction, which can be reduced by an injection-compression molding (ICM) process. In order to use the synergy from both processes, an injection-compression molding process with dynamic mold temperature control can be utilized. Within the scope of this investigation, the new process was reproduced by an ICM process at elevated mold temperature (ICM_EMT) and compared with injection molding (IM) with regard to molding accuracy and optical properties in dependence of component thickness and mold temperature. In order to evaluate the molding accuracy, the roughness of a wire-eroded microstructure on the cavity surface was measured. To determine the degree of orientation, the optical properties considered were the transmission and the path difference. It was shown that the adapted ICM process was able to achieve a high degree of replication accuracy with a low degree of orientation, especially for thin-walled components. ICM at elevated mold temperature reduced the path difference in the components with the lowest wall thickness by a factor of two while at the same time optimizing the replication of the microstructure. This could also be confirmed by transmission measurements. DOI : 10.3139/217.3802 En ligne : https://drive.google.com/file/d/1bMeibb5sQxYzP7WmZRsktl2UWvG7FUtN/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33061
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 425-433[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible Study of bonding formation between the filaments of PLA in FFF process / Achraf Kallel in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Study of bonding formation between the filaments of PLA in FFF process Type de document : texte imprimé Auteurs : Achraf Kallel, Auteur ; I. Koutiri, Auteur ; E. Babaeitorkamani, Auteur ; A. Khavandi, Auteur ; M. Tamizifar, Auteur ; M. Shirinbayan, Auteur ; A. Tcharkhtchi, Auteur Année de publication : 2019 Article en page(s) : p. 434-444 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Coalescence (Sciences physiques)
Etat fondu (matériaux)
FilamentsFibre de longueur infinie ou extrême comme celle qu'on trouve dans la soie à l'état naturel. Les fibres manufacturées sont extrudées en filaments qui sont transformés en fils continus, en fibres courtes ou en câbles.
Impression tridimensionnelle
Mesure
Modèles numériques
Polylactique, AcideL'acide polylactique (anglais : polylactic acid, abrégé en PLA) est un polymère entièrement biodégradable utilisé dans l'alimentation pour l'emballage des œufs et plus récemment pour remplacer les sacs et cabas en plastiques jusqu'ici distribués dans les commerces. Il est utilisé également en chirurgie où les sutures sont réalisées avec des polymères biodégradables qui sont décomposés par réaction avec l’eau ou sous l’action d’enzymes. Il est également utilisé pour les nouveaux essais de stent biodégradable.
Le PLA peut-être obtenu à partir d'amidon de maïs, ce qui en fait la première alternative naturelle au polyéthylène (le terme de bioplastique est utilisé). En effet, l'acide polylactique est un produit résultant de la fermentation des sucres ou de l'amidon sous l'effet de bactéries synthétisant l'acide lactique. Dans un second temps, l'acide lactique est polymérisé par un nouveau procédé de fermentation, pour devenir de l'acide polylactique.
Ce procédé conduit à des polymères avec des masses molaires relativement basses. Afin de produire un acide polylactique avec des masses molaires plus élevées, l'acide polylactique produit par condensation de l'acide lactique est dépolymérisé, produisant du lactide, qui est à son tour polymérisé par ouverture de cycle.
Le PLA est donc l’un de ces polymères, dans lequel les longues molécules filiformes sont construites par la réaction d’un groupement acide et d’une molécule d’acide lactique sur le groupement hydroxyle d’une autre pour donner une jonction ester. Dans le corps, la réaction se fait en sens inverse et l’acide lactique ainsi libéré est incorporé dans le processus métabolique normal. On obtient un polymère plus résistant en utilisant l'acide glycolique, soit seul, soit combiné à l’acide lactique.
Procédés de fabrication
Température
ThermocouplesIndex. décimale : 668.4 Plastiques, vinyles Résumé : Fused filament fabrication (FFF) is an additive manufacturing (AM) process that provides physical objects commonly used for modeling, prototyping and production applications. The major drawback of this process is poor mechanical property due to the porous structure of final parts. This process requires careful management of coalescence phenomenon. In this paper, the major influencing factors during the FFF processing of poly(lactic acid) (PLA) were investigated experimentally and with a numerical model. It has been shown that the polymer temperature has a significant effect on the rheological behavior of PLA, especially on the adhesion of the filaments. An experimental set-up has been placed in the machine to have the cyclic temperature of the filament. A variation of the polymer temperature influences process parameters such as feed rate, temperature of the nozzle and temperature of the platform. The results showed that the amount of polymeric coalescence (neck growth) rises when increasing the feed rate, the nozzle temperature, and the platform temperature. A model to predict the neck growth is proposed. It predicts a lower amount of neck growth value than obtained experimentally. This difference has been explained as the effect of other phenomena, such as polymer relaxation time, pressure of the nozzle and especially cyclic temperature which is not taken into account in the model. Note de contenu : - MATERIAL AND METHODS : Materials 3D printer and specimen preparation - Thermocouple and measurement equipment - Coalescence tes
- RESULTS AND DISCUSSION : FFF process - Real-time temperature evolution of filament - Effect of process parameters - Coalescence test
- PREDICTIVE MODEL : Theoretical basis and sintering modeling - Modified Pokluda model for the FFF process - Model resultsDOI : 10.3139/217.3718 En ligne : https://drive.google.com/file/d/1S9MpeV9lFASDUI5h1bua2wmANbsHkrKV/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33062
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 434-444[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible Rheology and extrusion foaming of partially crosslinked thermoplastic vulcanizates silicone / T. Métivier in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Rheology and extrusion foaming of partially crosslinked thermoplastic vulcanizates silicone Type de document : texte imprimé Auteurs : T. Métivier, Auteur ; Philippe Cassagnau, Auteur ; Charlène Forest, Auteur ; Grégory Martin, Auteur ; N. Garois, Auteur Année de publication : 2019 Article en page(s) : p. 445-456 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Dispersions et suspensions
Extrusion moussage
Mousses plastiques
Nucléation
Polyéthylène basse densité
Rhéologie
SiliconesLes silicones, ou polysiloxanes, sont des composés inorganiques formés d'une chaine silicium-oxygène (...-Si-O-Si-O-Si-O-...) sur laquelle des groupes se fixent, sur les atomes de silicium. Certains groupes organiques peuvent être utilisés pour relier entre elles plusieurs de ces chaines (...-Si-O-...). Le type le plus courant est le poly(diméthylsiloxane) linéaire ou PDMS. Le second groupe en importance de matériaux en silicone est celui des résines de silicone, formées par des oligosiloxanes ramifiés ou en forme de cage (wiki).
VulcanisationIndex. décimale : 668.4 Plastiques, vinyles Résumé : This work focuses on the foaming behavior of thermoplastic vulcanized silicones (TPVs) in which partially crosslinked silicone nodules are dispersed. In these TPVs, silicone nodules dispersed in a low density polyethylene (LDPE) phase have an average size of about 1 μm. The crosslinking densities of the elastomer phase were selected according to their viscoelastic behavior. Surprisingly, linear and non-linear shear rheology appeared more sensitive to formulations than extensional rheology. Indeed, each formulation has an extensional rheological behavior similar to that of pure LDPE and meets the requirements for foaming applications in terms of elongation at break and melt strength. In accordance with non-linear shear rheology, the foaming behavior of these formulations has been correlated to extrusion foaming parameters that are known to control nucleation, i. e. pre-die pressure and die exit depressurization rate. With an appropriate crosslinking density of silicone nodules, the TPV foamability tends to the foamability of pure LDPE to reach a foam density of 0.54 g/cm3 with an average cell size of 140 ± 50 μm and a cell density of 3 × 105 cells/cm3. Since partially crosslinked silicone nodules cannot foam, it is assumed that they improve nucleation while allowing sufficient expansion of the LDPE phase. Note de contenu : - EXPERIMENTAL PART : Materials - Sample preparation
- CHARACTERIZATION : Rheology - Swelling test - Scanning Electron Microscopy (SEM) - Extrusion foaming process - CO2 solubility in TPV
- RESULTS AND DISCUSSION : Viscoelasticity of LSR A/B blends without LDPE - TPV characterization - Extrusion foamingDOI : 10.3139/217.3741 En ligne : https://drive.google.com/file/d/1XQ_87ooFiCP3wxJfZNxaA8yqVg1Qli15/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33063
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 445-456[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible Influence of rubber ratio and crosslinking agent on mechanical properties, crystallization and rheological behaviors of EPDM/PP thermoplastic elastomer / D.-H. Xu in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Influence of rubber ratio and crosslinking agent on mechanical properties, crystallization and rheological behaviors of EPDM/PP thermoplastic elastomer Type de document : texte imprimé Auteurs : D.-H. Xu, Auteur ; Y. Zhou, Auteur ; W.-D. He, Auteur ; H.-M. Wu, Auteur ; J. Yu, Auteur Année de publication : 2019 Article en page(s) : p. 457-466 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Analyse mécanique dynamique
Analyse thermique
Caoutchouc -- Propriétés mécaniques
Cristallisation
Elastomères thermoplastiques -- Propriétés mécaniques
Ethylène-propylène-diène monomère
Morphologie (matériaux)
Polypropylène
Réticulants
Rhéologie
VulcanisationIndex. décimale : 668.4 Plastiques, vinyles Résumé : The ethylene-propylene-diene monomer/polypropylene (EPDM/PP) thermoplastic elastomer is prepared by dynamic vulcanization. The effects of different rubber ratios and crosslinking agent contents on the static and dynamic mechanical properties, crystallization and rheological behaviors are investigated and discussed. EPDM/PP with the rubber ratio from 40 to 50 % and crosslinking agent content of 1.2 wt% has the highest tensile strength and elongation at break. The fracture morphologies indicate that EPDM/PP with high rubber ratios and crosslinker contents is over vulcanized to harden, which results in that some large particles cannot be fragmented by shear force. The crystallinity obtained from differential scanning calorimetry (DSC) shows a decrease with increasing rubber ratio and a very slight variation with increasing the crosslinking content. The dynamic mechanical analysis (DMA) results display a decrease trend in storage modulus and tan δ with increasing crosslinking density. The rheological behaviors show that the complex viscosity also increases with increasing crosslinking density, indicating that the elastic deformation becomes superior to viscous flow in EPDM/PP. Note de contenu : - EXPERIMENTAL : Materials - Preparation of samples - Measurements and characterization
- RESULTS AND DISCUSSION : Mechanical properties - Morphology analysis - Crystallization behavior - Dynamic mechanical properties - Rheology behaviorDOI : 10.3139/217.3817 En ligne : https://www.degruyter.com/document/doi/10.3139/217.3817/pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33064
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 457-466[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible Effect of annealing temperature on PP microporous membranes obtaines by a melt-extrusion-stretching method / Z. Y. Liu in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 4 (08/2019)
[article]
Titre : Effect of annealing temperature on PP microporous membranes obtaines by a melt-extrusion-stretching method Type de document : texte imprimé Auteurs : Z. Y. Liu, Auteur ; X.-T. Wu, Auteur ; J. Yan, Auteur ; W. Yang, Auteur ; M.-B. Yang, Auteur Année de publication : 2019 Article en page(s) : p. 467-474 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Etat fondu (matériaux)
Extrusion par étirage
Matériaux poreux
Membranes (technologie)
PolypropylèneIndex. décimale : 668.9 Polymères Résumé : Isotactic polypropylene (iPP) precursor film with highly oriented lamellar structure was produced through a melt extrusion-annealing-uniaxial stretching (MAUS) process. The precursor films were annealed at various temperatures and the structure evolution of precursor films during various annealing temperatures and the pore formation of the annealed film during stretching were investigated. During annealing, recrystallized lamellar structure was formed to obtain “core-shell sandwich” structure. The thickness of newly formed lamellae increased with annealing temperature, which improved the ability of slipping resistance of the original lamellar structure during stretching. As the annealing temperature of precursor film increased, the micropore shape and diameter of the final membranes became more uniform. The porosity of the microporous membranes increased with increasing annealing temperature. Note de contenu : - EXPERIMENTAL : Material and membrane preparation - Characterization
- RESULTS AND DISCUSSION : Effect of annealing temperature on the lamellar structure of the precursor films - Effect of annealing temperature on the tensile deformation behavior of the precursor films - Effect of annealing on the performance of the microporous membranes - DiscussionDOI : 10.3139/217.3774 En ligne : https://www.degruyter.com/document/doi/10.3139/217.3774/pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33065
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 4 (08/2019) . - p. 467-474[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21083 - Périodique Bibliothèque principale Documentaires Disponible
Exemplaires (1)
Code-barres | Cote | Support | Localisation | Section | Disponibilité |
---|---|---|---|---|---|
21083 | - | Périodique | Bibliothèque principale | Documentaires | Disponible |