Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Macroscopic volume, van der waals volume and free volume after cure versus chemical conversion for a high-Tg epoxy/amine thermosetting system / R. A Venditti in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 67, N° 844 (05/1995)
[article]
Titre : Macroscopic volume, van der waals volume and free volume after cure versus chemical conversion for a high-Tg epoxy/amine thermosetting system Type de document : texte imprimé Auteurs : R. A Venditti, Auteur ; J. K. Gillham, Auteur ; Y. Lou, Auteur ; Y. C. Jean, Auteur Année de publication : 1995 Article en page(s) : p. 47-56 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Calorimétrie
Dilatation (thermodynamique)
Epoxydes
Polyamines
Positons -- Annihilation
Réticulation (polymérisation)
Thermodurcissables
Transition vitreuseIndex. décimale : 667.9 Revêtements et enduits Résumé : sothermal glassy-state properties of cured thermosetting materials pass through maximum and minimum values with increasing chemical conversion. In this work a diglycidyl ether of bisphenol A (a diepoxide) and trimethylene glycol di-p-aminobenzoate (a tetra-functional aromatic diamine) system (DGEBA/TMAB) has been investigated for the purpose of analyzing the behavior after cure of the isothermal properties of the glass with increasing conversion. The glass transition temperature (Tg) is used as a direct measure of conversion. The density, Tg, modulus, and free volume of the material after cure with increasing conversion was measured. The specific volume at 25°C after cure passes through a minimum and the modulus passes through a maximum with increasing conversion (Tg). The fractional fraction free volume at 25°C after cure passes through a minimum value with respect to conversion. The specific volume, modulus, and fractional free volume at 25°C versus conversion data qualitatively correlate Note de contenu : - EXPERIMENTAL : Chemical system - Mixing procedure - Cure procedure - Density measurements - DSC measurements - Thermal expansion coefficient measurements - positron annihilation spectroscopy
- RESULTS AND DISCUSSION : Specific volume versus conversion - Packing density at 298K versus conversion - Comparison of van der waals volume and specific volume versus conversion - Free volume versus conversion - AntiplasticizationPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=18512
in JOURNAL OF COATINGS TECHNOLOGY (JCT) > Vol. 67, N° 844 (05/1995) . - p. 47-56[article]Réservation
Réserver ce document
Exemplaires (2)
Code-barres Cote Support Localisation Section Disponibilité 003490 - Périodique Bibliothèque principale Documentaires Disponible 003502 - Périodique Bibliothèque principale Documentaires Exclu du prêt Managing flame retardant performance in modern thermoset applications / Frank Osterod in JEC COMPOSITES MAGAZINE, N° 126 (01-02/2019)
[article]
Titre : Managing flame retardant performance in modern thermoset applications Type de document : texte imprimé Auteurs : Frank Osterod, Auteur Année de publication : 2019 Article en page(s) : p. 18-20 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Calorimétrie
Epoxydes
Essais de comportement au feu
Fumée -- Analyse
IgnifugeantsComposé chimique utilisé pour réduire l'inflammabilité. Il peut être incorporé au produit durant sa fabrication ou appliqué ultérieurement à sa surface.
Industrie ferroviaire -- Matériaux
Intumescence (chimie)
Normalisation
ThermodurcissablesIndex. décimale : 668.4 Plastiques, vinyles Résumé : In our daily life, we are often surrounded - without knowing it - by composites. These materials are used in transportation applications where lightweight structures are of great importance to save energy. Moreover, demanding fire safety standards have to be fulfilled, such as for aviation and railway applications. In these thermoset composites fire, smoke and toxicity have to be controlled. Note de contenu : - Burning behaviour
- Flame retardant mixtures
- Good performance
- European railway standard
- Fig. 1 : Intumescent layer with char after a cone calorimeter test
- Fig. 2 : HRR curve of an epoxy composite with Exolit flame retardant
- Fig. 3 : Cone calorimeter with a burning sample
- Fig. 4 : Example of modern aircraft interior, all composite components have to pass demanding fire, smoke and toxicity tests
- Table 1 : Overview of the EN 45545-2, R1 requirementsPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=31770
in JEC COMPOSITES MAGAZINE > N° 126 (01-02/2019) . - p. 18-20[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 20472 - Périodique Bibliothèque principale Documentaires Disponible Mesure de la viscosité élongationnelle apparente / G. Chaidron in CAOUTCHOUCS & PLASTIQUES, N° 812 (04/2003)
[article]
Titre : Mesure de la viscosité élongationnelle apparente Type de document : texte imprimé Auteurs : G. Chaidron, Auteur ; Francisco Chinesta, Auteur ; J. Bouton, Auteur Année de publication : 2003 Article en page(s) : p. 28-33 Note générale : Bibliogr. Langues : Français (fre) Catégories : Calorimétrie
Polyéthylène basse densité
Polymères
Rhéologie
Viscosimétrie
ViscositéIndex. décimale : 668.4 Plastiques, vinyles Résumé : De nombreux travaux ont montré que la viscosité élongationnelle apparente a une influence considérable sur les écoulements complexes. Applications aux polymères et résultats obtenus. Note de contenu : - PRINCIPES DE LA MESURE : Description de la filière - Mesure de la viscosité de cisaillement - Évaluation de la viscosité élongationnelle - Modes de fonctionnement
- ÉTUDE RHÉOMÉTRIQUE DE DEUX PEbd : Techniques classiques - Rhéométrie capillaire - Rhéométrie oscillante en géométrie plan-planPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=23852
in CAOUTCHOUCS & PLASTIQUES > N° 812 (04/2003) . - p. 28-33[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 000517 - Périodique Bibliothèque principale Documentaires Disponible Methylcyclohexyl diamine (Baxxodur EC 210) - a hardener for epoxy systems with superior carbamate stability / Irene Gorman in SURFACE COATINGS INTERNATIONAL, Vol. 101.5 (10-11/2018)
[article]
Titre : Methylcyclohexyl diamine (Baxxodur EC 210) - a hardener for epoxy systems with superior carbamate stability Type de document : texte imprimé Auteurs : Irene Gorman, Auteur ; Michael Henningsen, Auteur ; Frank Hettche, Auteur ; Matthaeus Kopczynski, Auteur ; Alexander Panchenko, Auteur ; Marc Hofmann, Auteur ; Chin Li, Auteur ; Raj Sundar, Auteur Année de publication : 2018 Article en page(s) : p. 258-262 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Calorimétrie
DiamineUne diamine est un type de polyamine contenant exactement deux groupes amine. Les diamines sont principalement utilisées comme monomères pour synthétiser des polyamides, des polyimides et des polyurées. La principale diamine produite est le 1,6-diaminohexane, précurseur du Nylon 6-6, suivie de l'éthylènediamine1. L'hydrazine (H2NNH2) n'est en général pas considérée comme une diamine puisque ce n'est ni une amine (pas de carbone), ni une dibase.
Epoxydes
Éther de diglycidyle et de bisphénol A
Réticulants
Revêtements -- Additifs
Revêtements -- Propriétés mécaniques
RhéologieIndex. décimale : 667.9 Revêtements et enduits Résumé : Epoxy-based industrial maintenance coatings «fer excellent chemical and mechanical performance. However, the amine type hardeners often employed can easily react with atmospheric carbon dioxide and moisture to form carbamate salts. These carbamate salts accumulate on the surface and cause blush and intercoat adhesion issues. Adducts based on methylcyclohexyl diamine (MCDA, Baxxodur EC 210), a cycloaliphatic diamine curative for epoxy resin systems, displayed enhanced carbamate stability when compared to adducts based on both isophorone diamine (IPDA) and m-xylylene diamine (MXDA). This behaviour was further validated in coating tests, where coating formulations based on MCDA exhibited superior gloss. The cure behaviour, mechanical properties, and thermal properties of MCDA, IPDA, and MXDA cured systems were also assessed using various analytical techniques such as differential scanning calorimetry and rheology. Overall, MCDA was proven to be an attractive building block for epoxy diamine industrial coating systems. Note de contenu : - EXPERIMENTAL : Materials - Adduct synthesis - Preparation of reactive DGEBA-adduct mixtures - Methods
- RESULTS AND DISCUSSION : Adduct production - Thermal properties - Rheological properties - Carbamate stability
- Fig. 1 : Diamine-type epoxy hardeners employed in this study
- Fig. 2 : Idealised MCDA-based adduct
- Fig. 3 : Viscosity development of DGEBA hardened with the various adducts and adduct-BnOH mixtures, at a) 23°C and b) 75°C. Viscosity data for DGEBA hardened with IPDA-A8 is not reported because the starting viscosity of this formulation exceeded 10000 mPas
- Fig. 4 : Shore D development over time of DGEBA hardened with MCDA-A16, IPDAA16, and MXDA-A16 adducts at 23°C (ambient atmosphere)
- Fig. 5 : Adducts and adduct-BnOH mixtures aged at 23°C and 50% relative humidity for 48 hours. The presence of carbamates was detected visually through the observation of white precipitate or surface irregularities, as was the case for IPDA-A2.5-BnOH
- Fig. 6 : Carbamate stability of pure adducts and adduct-BnOH mixtures aged at 23°C and 50% relative humidity, and spectral gloss readings of DGEBA hardened with A2.5-BnOH adducts at 8°C and 70% relative humidity
- Table 1 : Summary of adducts and adduct-BnOH mixtures
- Table 2 : Thermal properties of DGEBA hardened with adducts and adduct-BnOH mixtures
- Table 3 : Rheological properties of DGEBA hardened with adducts and adduct-BnOH mixtures
- Table 4 : Shore D and tack development of DGEBA hardened with adducts and adduct-BnOH mixturesEn ligne : https://drive.google.com/file/d/1dnph6wSwc5MaA4x6fGb3WMYc6rqh8L6d/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=31657
in SURFACE COATINGS INTERNATIONAL > Vol. 101.5 (10-11/2018) . - p. 258-262[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 20356 - Périodique Bibliothèque principale Documentaires Disponible Methylcyclohexyl diamine (Baxxodur® EC 210) / Irene Gorman in COATINGS WORLD, Vol. 23, N° 5 (05/2018)
[article]
Titre : Methylcyclohexyl diamine (Baxxodur® EC 210) : A hardener for epoxy systems with superior carbamate stability Type de document : texte imprimé Auteurs : Irene Gorman, Auteur ; Michael Henningsen, Auteur ; Frank Hettche, Auteur ; Matthaeus Kopczynski, Auteur ; Alexander Panchenko, Auteur ; Marc Hofmann, Auteur ; Chin Li, Auteur ; Raj Sundar, Auteur Année de publication : 2018 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Calorimétrie
Epoxydes
Méthylcyclohexyl diamine
Réticulants
Revêtements -- Additifs
Revêtements -- Propriétés mécaniques
Revêtements -- Propriétés thermiques
Revêtements organiques
RhéologieIndex. décimale : 667.9 Revêtements et enduits Résumé : Epoxy-based industrial maintenance coatings offer excellent chemical and mechanical performance. However, the amine type hardeners often employed can easily react with atmospheric carbon dioxide and moisture to form carbamate salts. These carbamate salts accumulate on the surface and cause blush and intercoat adhesion issues. Adducts based on methylcyclohexyl diamine (MCDA, Baxxodur® EC 210), a cycloaliphatic diamine curative for epoxy resin systems, displayed enhanced carbamate stability compared to adducts based on both isophorone diamine (IPDA) and m-xylylene diamine (MXDA). This behaviour was further validated in coating tests, where coating formulations based on MCDA exhibited superior gloss. The cure behavior, mechanical properties, and thermal properties of MCDA, IPDA, and MXDA cured systems were also assessed using various analytical techniques such as differential scanning calorimetry and rheology. Overall, MCDA was proven to be an attractive building block for epoxy diamine, industrial coating systems. Note de contenu : - EXPERIMENTAL : Materials - Adduct synthesis - Preparation of reactive DEGBA-adduct - Mixtures - Methods
- RESULTS AND DISCUSSION : Adduct production - Thermal properties - Rheological properties - Shore D development - Carbamate stability
- Fig. 1 : Diamine-type epoxy hardeners employed in this study
- Fig. 2 : Idealized MCDA-based adduct
- Fig. 3 : Viscosity development of DGEBA hardened with the various adducts and adduct-BnOH mixtures, at a) 23 °C and b) 75 °C. Viscosity data for DGEBA hardened with IPDA-A8 is not reported because the starting viscosity of this formulation exceeded 10,000 mPas
- Fig. 4 : Shore D development over time of DGEBA hardened with MCDA-A16, IPDA A16, and MXDA-A16 adducts at 23 °C (ambient atmosphere)
- Fig. 5 : Adducts and adduct-BnOH mixtures aged at 23 °C and 50% relative humidity for 48 hours. The presence of carbamates was detected visually through the observation of white precipitate or surface irregularities, as was the case for IPDA-A2.5-BnOH
- Fig. 6 : Carbamate stability of pure adducts and adduct-BnOH mixtures aged at 23 °C and 50% relative humidity, and spectral gloss readings of DGEBA hardened with A2.5-BnOH adducts at 8 °C and 70% relative humidity
- Table 1 : Summary of adducts and adduct-BnOH mixtures
- Table 2 : Thermal properties of DGEBA hardened with adducts and adduct-BnOH mixtures
- Table 3 : Rheological properties of DGEBA hardened with adducts and adduct-BnOH mixtures
- Table 4 : Shore D and tack development of DGEBA hardened with adducts and adduct-BnOH mixturesEn ligne : https://www.coatingsworld.com/issues/2018-05-01/view_features/methylcyclohexyl-d [...] Format de la ressource électronique : Html Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=32520
in COATINGS WORLD > Vol. 23, N° 5 (05/2018)[article]Modern methods in fiber analysis for advanced quality control and process development / Wilhelm Steinmann in CHEMICAL FIBERS INTERNATIONAL, Vol. 62, N° 2 (05/2012)
PermalinkModification et caractérisation de surface de matériaux fibreux / Ahmida El Achari / 2007
PermalinkMorphology influence of nanoporous nickel phosphate on intumescent flame retardant polypropylene composites / S.-B. Nie in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIII, N° 4 (08/2018)
PermalinkMultifunctional photoinitiators (MFPIs) : A new concept / R. Burrows in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 87, B2 (06/2004)
PermalinkPermalinkA new class of silicone resins for coatings / Mark D. Soucek in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 4, N° 3 (09/2007)
PermalinkNotable electrical and mechanical properties of polyacrylamide (PAM) with graphene oxide (GO) and single-walled carbon nanotubes (SWCNTs) / Seema Awasthi in INTERNATIONAL POLYMER PROCESSING, Vol. 38, N° 3 (2023)
PermalinkNumerical simulation of the injection blow molding single stage process : shaping of two different geometries and comparison with experimental thickness measurements / Jordan Biglione in INTERNATIONAL POLYMER PROCESSING, Vol. XXXI, N° 4 (08/2016)
PermalinkUn outil pour différencier deux polypropylènes / Angela Hammer in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 919 (03/2015)
PermalinkPerformance evaluation of dimethyl silicone oil as archaeological dry leather lubricant / Alireza Koochakzaei in JOURNAL OF THE AMERICAN LEATHER CHEMISTS ASSOCIATION (JALCA), Vol. CXV, N° 4 (04/2020)
PermalinkPlastiques. Analyse calorimétrique différentielle (DSC) - Partie 3 : Détermination de la température et de l'enthalpie de fusion et de cristallisation - Norme NF EN ISO 11357-3 / Association Française de Normalisation (Paris) / Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) (2013)
PermalinkPlastiques. Matériaux semi-cristallins. Détermination de la température de fusion conventionnelle par analyse thermique - Norme NF T 51-223 / Association Française de Normalisation (Paris) / Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) (1985)
PermalinkPlastiques. Résines phénoliques - Norme NF EN ISO 11409 / Association Française de Normalisation (Paris) / Saint-Denis La Plaine : Association Française de Normalisation (AFNOR) (1998)
PermalinkPolyamide resin dispersion offers beneficial properties for coated roll stock uses / Palitha K. Abeywardena in ADHESIVES AGE, Vol. 40, N° 2 (02/1997)
PermalinkPowdered hide model for vegetable tanning / Eleanor M. Brown in JOURNAL OF THE AMERICAN LEATHER CHEMISTS ASSOCIATION (JALCA), Vol. CIX, N° 1 (01/2014)
PermalinkPowdered hide model for vegetable tanning II : hydrolyzable tannin / Eleanor M. Brown in JOURNAL OF THE AMERICAN LEATHER CHEMISTS ASSOCIATION (JALCA), Vol. CX, N° 1 (01/2015)
PermalinkPreparation and property of phase change fiber by electrospinning / Hong Yan Wu in CHEMICAL FIBERS INTERNATIONAL, Vol. 68, N° 1 (03/2018)
PermalinkProduction of thermoplastic elastomers based on recycled PE and ground tire rubber : morphology, mechanical properties and effect of compatibilizer addition / Y.-H. wang in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIII, N° 4 (08/2018)
PermalinkProtection feu par système intumescent / Carole Magnier in TEXTILES A USAGES TECHNIQUES (TUT), N° 45 (3e trimestre 2002)
PermalinkQuoi de neuf depuis la calorimétrie de Lavoisier et de Berthelot ? / Jean Rouquerol in L'ACTUALITE CHIMIQUE, N° 441 (06/2019)
Permalink