Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
[article]
Titre : No more weight problems : Dynamic adjustment of switchover pressure and holding pressure to achieve a constantpart weight Type de document : texte imprimé Auteurs : Benjamin Pearson, Auteur ; Patrick Pazour, Auteur Année de publication : 2020 Article en page(s) : p. 25-27 Langues : Anglais (eng) Catégories : Logiciels
Matières plastiques -- Moulage par injection
Poids -- Contrôle
Pression -- ContrôleIndex. décimale : 668.4 Plastiques, vinyles Résumé : HiQ Flow is Wittmann Battenfeld’s answer to the challenge of fluctuating shot weights in injection-molded parts. The assistant system modifies the process parameters in the course of the same shot to counteract vis-cosity fluctuations caused by batch fluctuations in the material or by the use of regrind. Note de contenu : - How does the assistance system function ?
- Benchmark test with automotive components
- Cavity pressure as a decisive reference value for quality
- A question of distribution
- Figure : The HiQ Flow software corrects viscosity deviations during the injection and holding pressure phases within the same shot, based on the measurement values taken from the injection molding machine
- Fig. 1 : Injection profile over time for two materials of different viscosities (blue for low and red for high viscosity), with active support from HiQ Flow. The highlighted area represents the period of time for which the injection work is calculated. HiQ Flow shifts the changeover point and the holding pressure level within the same shot on the basis of reference values
- Fig. 2 : Peak cavity pressure per shot for three different materials. In the first section, HiQ Flow is deactivated, in the second section, it is switched on. This shows that with HiQ Flow being acti-vated, a stationary cavity pressure and consequently repeatable cavity filling has been achieved
- Fig. 3 : Combined box plot to compare the peak cavity pressures per material and test series
- Fig. 4 : Combined box plot for comparison of the maximum peak cavity pressures with deactivated and activated HiQ FlowEn ligne : https://drive.google.com/file/d/1vqso-M0QdRC2qEk5BqSnif4OYykdyq9a/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=34813
in KUNSTSTOFFE INTERNATIONAL > Vol. 110, N° 7 (2020) . - p. 25-27[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 22209 - Périodique Bibliothèque principale Documentaires Disponible Du nouveau dans la prévention des risques chimiques / Raymond Vincent in HYGIENE & SECURITE DU TRAVAIL, N° 238 (01-02-03/2015)
[article]
Titre : Du nouveau dans la prévention des risques chimiques Type de document : texte imprimé Auteurs : Raymond Vincent, Auteur ; Annabel Maison, Auteur ; Nicolas Bertrand, Auteur ; Florian Marc, Auteur ; Frédéric Clerc, Auteur ; Stéphane Malard, Auteur ; Nathalie Toutlemonde, Auteur ; Fabrice Leray, Auteur ; Christine Guichard, Auteur ; Gautier Mater, Auteur Année de publication : 2015 Article en page(s) : p. 22-47 Note générale : Bibliogr. Langues : Français (fre) Catégories : Chrome hexavalent -- Toxicologie
Logiciels
Maladies professionnelles -- Prévention
Produits chimiques -- Classification
Produits chimiques -- Etiquetage
Produits chimiques -- Toxicologie
Règlements de sécurité
Risques industriels
Sécurité du travail
Styrène -- Toxicologie
Substances dangereuses -- Evaluation du risqueIndex. décimale : 363.11 Risques professionnels et industriels Résumé : En 2015, deux actualités marqueront la prévention des risques chimiques, qui concerne presque tous les secteurs d'activité. Au niveau européen, le règlement CLP devient l'unique système de classification, d'étiquetage et d'emballage des substances et mélanges chimiques. En France, le logiciel Seirich sera mis en ligne afin d'aider les entreprises à évaluer leurs risques, à mieux connaître leurs obligations réglementaires et à mettre en place un plan de prévention.
Ce dossier fait le point sur ces deux sujets et présente également les résultats de campagnes d'évaluation des expositions à deux substances particulièrement dangereuses : le chrome VI et le styrène.Note de contenu : - LES PRODUITS CHIMIQUES AU TRAVAIL : DES RISQUES SOUVENT IGNORES : Identifier les dangers - Evaluer les risques - Définir les action de prévention
- REGLEMENT CLP : COMPRENDRE LA CLASSIFICATION ET L'ETIQUETAGE DES PRODUITS CHIMIQUES : Les dates d'application - Classer une substance - Classer un mélange - Comment est étiqueté un produit ? - Quelques sources d'information officielles
- SEIRICH, UN LOGICIEL D'EVALUATION ET D'INFORMATION SUR LES RISQUES CHIMIQUES : L'architecture technique - L'accompagnement des entreprises
- CHROME VI, DES EXPOSITIONS ELEVEES ET PREOCCUPANTES : Ferrochrome-chrome - Peinture et aéronautique - Traitement de surface - Soudage - Découpe, plasma, laser - Traitement du bois - Autres secteurs investigués
- STYRENE ET POLYESTER STRATIFIE : NIVEAU D'EXPOSITION ET ACTIONS DE PREVENTION : La campagne de mesures 2013 - Exploitation des données métrologiques - Exploitation des questionnaires d'évaluation des moyens de prévention - Moyens de prévention à privilégierEn ligne : http://www.inrs.fr/media.html?refINRS=DO%208 Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=23613
in HYGIENE & SECURITE DU TRAVAIL > N° 238 (01-02-03/2015) . - p. 22-47[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 17112 - Périodique Bibliothèque principale Documentaires Disponible
[article]
Titre : Numbers that count : with its iQ weight monitor, engel shifts process monitoring one step up Type de document : texte imprimé Auteurs : Josef Giessauf, Auteur ; Christian Maier, Auteur ; Paul Kapeller, Auteur ; Georg Pillwein, Auteur ; Georg Steinbichler, Auteur Année de publication : 2017 Article en page(s) : p. 28-32 Langues : Anglais (eng) Catégories : Logiciels
Matières plastiques -- Moulage par injection
Procédés de fabricationIndex. décimale : 668.4 Plastiques, vinyles Résumé : Cyclically measured process parameters are used for monitoring and optimizing injection molding processes. In the past, attention was focused on axis movements and the associated necessary forces and times. Now, the software package iQ weight monitor goes a large step further. It generates process parameters that are relevant for component quality: injected volume, melt viscosity variation, and pressure deviations during injection. Note de contenu : - Focus on filling procedure
- Classics under scrutiny
- Process parameters with significance
- Reduced outlay, large benefits
- Process monitoring with control possibilities
- FIGURES : 1. In spite of their limited significance, melt cushion and flow number were frequently used in the past for process monitoring - 2. Changes of injection volume, viscosity, and the pressure curve can influence component quality. In the worst case, as shown here, various interference factors occur together. For better understanding, very large deviations from the reference curve have been selected here - 3. the respective actual process parameters are shown clearly on the display of the machine control system. The traffic light colors indicate which values are within or outside the tolerance range
- TABLES : 1. Intentional manipulations of the process and their influence on component weitght and also on the two process parameters melt cushion and flow number. The colors indicate the significance of the process parameters. Green : The process parameters has changed in the expected direction. Red : The process parameter has changed contrary to the expectation - 2. Intentionally introduced process changes and their influences on component weight : The process parameters injection volume and viscosity change in the respective expected directions. The changes of injection volume are greater than for component weight, as the sprue was not taken into account in the latter - 3. The iQ weight monitor provideshighly significant process parametersEn ligne : https://drive.google.com/file/d/149hRD4HTZS3LPrs3CwmZdpOTSJ-XPWpm/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=29099
in KUNSTSTOFFE INTERNATIONAL > Vol. 107, N° 9 (09/2017) . - p. 28-32[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19135 - Périodique Bibliothèque principale Documentaires Disponible Numerical and analytical study of fatigue and degradation in multilayer composite plates / Amin Moslemi Petrudi in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 30, N° 2 (04/2020)
[article]
Titre : Numerical and analytical study of fatigue and degradation in multilayer composite plates Type de document : texte imprimé Auteurs : Amin Moslemi Petrudi, Auteur Année de publication : 2020 Note générale : Bibliogr. Langues : Français (fre) Catégories : Composites -- Détérioration
Composites -- Rupture
Composites à fibres de carbone -- Propriétés mécaniques
Epoxydes
Logiciels
Matériaux -- Fatigue
Rupture (mécanique)
Structures multicouchesIndex. décimale : 668.4 Plastiques, vinyles Résumé : Composite laminates are widely used in civil engineering, aerospace, shipbuilding and the military industry because of their high strength and rigidity to their high weight ratio, good fatigue resistance and high energy absorption fineness. The mechanism of degradation in composites is very complex and one or more degradation modes may occur in the composites at the same time. In this paper, multi-layer composite degradation with stress concentration due to internal hole is investigated numerically and analytically. The miso-scale model is used to investigate the problem. Fortran and Ansys software have been used to analyze the problem. The usermat code is embedded in Fortran software and linked to Ansys software. The present paper solves the stress induced multilayers in the present study, and compares the results of this method with those of other researchers. Stress and damage contours have been reported. it is shown Change of the diameter of the central open-hole not only the effect on possible damage, damaging rate, progressive damage but also effect on the strength of the composite laminates is also indicated. Note de contenu : - MODEL OF THE FAILURE MECHANICS OF CONTINUOUS : Effective tension - Effective response - Thermodynamic forces - Evolution of destruction - Criterion of destruction
- USERMAT CODE
- MESH EVALUATION
- VALIDATION USING EXPERIMENTAL RESULTS
- RESULTS AND DISCUSSIONS
- Table 1 : Literature review in composite materials research
- Table 2 : IM6/914 composite the properties
- Table 3 : Constant material parameters
- Table 4 : Investigating the independence of mesh
- Table 5 : The Dimensions ModelDOI : https://doi.org/10.18280/rcma.300202 En ligne : https://www.iieta.org/download/file/fid/33118 Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=37588
in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 30, N° 2 (04/2020)[article]Numerical and experimental study of bio-composite plates as internal fixation / Tamara R. Kadhim in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 33, N° 1 (02/2023)
[article]
Titre : Numerical and experimental study of bio-composite plates as internal fixation Type de document : texte imprimé Auteurs : Tamara R. Kadhim, Auteur ; Jawad Kadhim Oleiwi, Auteur ; Qahtan A. Hamad, Auteur Année de publication : 2023 Article en page(s) : p. 21-29 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Dioxyde de titane
Eléments finis, Méthode des
Implants médicaux
Implants orthopédiques
Logiciels
Matériaux hybrides
Matériaux hybrides -- Propriétés mécaniques
Plaques (ingénierie)
Polyéthylène à ultra haut poids moléculaire
Polymères en médecine
ProthèsesIndex. décimale : 668.4 Plastiques, vinyles Résumé : Bone plates are essential for bone fracture healing because they modify the biomechanical microenvironment at the fracture site to provide the necessary mechanical fixation for fracture fragments. This paper focuses on reducing the stress shielding effect that occurs due to a mismatch between cortical bone and metal plate. fabricating bio composites plates fixation by modeling of femur bone with ANSYS software program. However, Bio-composites that involve Ultra-high molecular weight polyethylene polymer (UHMW-PE) reinforced with nano Titanium dioxide particles n-TiO2 at different fractions (0, 1.5, 2.5, 3.5 and 4.5%) and 5% from carbon and Kevlar fibers were fabricated by hot pressing technique. We tested tensile, elastic modulus, and elongation percentages. The results of this study showed a value of tensile strength and elastic modulus improved with increasing weight fraction of nanoparticles and UHMWPE+4.5% n-TiO2 biocomposite were the best mechanical properties, were tensile strength and elastic modulus was (38.57 ± 1.9285 MPa, 1.15 ± 0.0575 GPa) respectively and elongation percentages reduced to 114.05 ±5.7025% compared with pure UHMWPE 176.68 ± 5.7025%. According to the current study's findings, it is possible to create bio-composites as fixation devices with improved performance by placing different fiber reinforcements. Note de contenu : - Experimental work
- Mechanical properties of bio-composites
- Finite element modeling
- Experimental results
- Numerical results
- Table 1 : Material properties of bone plates and bonesDOI : https://doi.org/10.18280/rcma.330104 En ligne : https://iieta.org/download/file/fid/91633 Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39262
in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 33, N° 1 (02/2023) . - p. 21-29[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 24132 - Périodique Bibliothèque principale Documentaires Disponible Optimizing the key manufacturing parameters of the AFP process / Lei Shi in JEC COMPOSITES MAGAZINE, N° 122 (07/2018)
PermalinkUn outil au service de la plasturgie / Chrystel Simone in PLASTIQUES & CAOUTCHOUCS MAGAZINE, N° 873 (01-02/2010)
PermalinkProgramming and simulating automated fiber placement (AFP) CNC machines / B. Hasenjaeger in SAMPE JOURNAL, Vol. 49, N° 6 (11-12/2013)
PermalinkPrometheus should handle it in KUNSTSTOFFE INTERNATIONAL, Vol. 111, N° 1 (2021)
PermalinkProtecpo, un outil de pré-sélection de matériaux de protection cutanée / Alain Chollot in HYGIENE & SECURITE DU TRAVAIL, N° 235 (04-05-06/2014)
PermalinkPyris 1 DSC, un outil indispensable / R. B. Cassel in CAOUTCHOUCS & PLASTIQUES, N° 789 (10/2000)
PermalinkPermalinkPermalinkA quantum leap in INTERNATIONAL SURFACE TECHNOLOGY (IST), Vol. 10, N° 1 (2017)
PermalinkRecyclage : le P/ID 28, un nouvel outil d'analyse / Irma Geyer in CAOUTCHOUCS & PLASTIQUES, N° 751 (06/1996)
PermalinkSimpler solution complex coating came / Peter Ho in PROTECTIVE COATINGS EUROPE (PCE), Vol. 5, N° 2 (04-05-06/2013)
PermalinkSimulator for spray painting for objective assessment and quicker training / M. Raja in PAINTINDIA, Vol. LXVIII, N° 4 (04/2018)
PermalinkPermalinkSoftware helps reduce time to market for fibre-reinforced plastic control arm / Fabio Pulina in JEC COMPOSITES MAGAZINE, N° 126 (01-02/2019)
PermalinkSoftware systems for smart paint shops in INTERNATIONAL SURFACE TECHNOLOGY (IST), Vol. 12, N° 3 (2019)
Permalink