Accueil
Catégories
> Polyamide 66
Polyamide 66Voir aussi
|
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
[article]
Titre : Drivers of electromobility : Flame retardancy, heat and tracking resistance of electric vehicles Type de document : texte imprimé Auteurs : Yu Bin, Auteur ; Tamim Sidiki, Auteur ; David Zhu, Auteur Année de publication : 2020 Article en page(s) : p. 8-13 Langues : Anglais (eng) Catégories : Ignifugeants Composé chimique utilisé pour réduire l'inflammabilité. Il peut être incorporé au produit durant sa fabrication ou appliqué ultérieurement à sa surface.
Matières plastiques dans les automobiles
Piles électriques
Polyamide 6
Polyamide 66
Polymères ignifuges
Résistance thermique
Véhicules électriquesIndex. décimale : 668.4 Plastiques, vinyles Résumé : The transformation from the combustion to the electric engine entails several imponderabilities for the plastics industry. In part, electric drives have completely different material requirements which are becoming specifically evident with the increasing use of appropriate vehicles. The following article presents an overview of the most important changes. Note de contenu : - Flame protection is required
- ID.2 reaches USD 100 per kWh
- Without halogens, phosphar and halides
- Reasons for electric breakdown
- Figure : In electric vehicles, the change in engine technology also entails new requirements for the plastic materials used
- Fig. 1 : Key components of the high voltage drive train system of a Chevrolet Bolt
- Fig. 2 : PA is a very suitable material also for EV applications. For instance, PA6 and PA66 are used in HV connectors, HV PA 4T busbars and contactors
- Fig. 3 : Terminal corrosion caused by outgassed heat stabilizers of migration of other ionic impurities in the plastic
- Fig. 4 : In order to increase the the voltage rather than the current
- Fig. 5 : The creep distance is often deliberately increased to prevent the flow of current between two contacts
- Fig. 6 : Comparison of different polymer classes by tracking resistance. Colors indicate respective mechanical strength
- Fig. 7 : Electric breakdown strength before aging at-elevated temperatures. Most polymers show a decline in breakdown strentgh at rising temperatures
- Fig. 8 : Electric breakdown strength after aging at elevated temperatures. The curves of the materials are similar before and after aging. As a result of aging, the dielectric strength decreases as expected
- Fig. 9 : DSM high-voltage material portfolio for high operating temperatures. Different materials are recommended depending on the temperature range
- Fig. 10 : Functional diagram of the powertrain in a battery electric vehicle. Electrification adds further components
- Table 1 DSM portfolio of compounds without critical halide salts or red phosphorous, which could lead to electro corrosionEn ligne : https://drive.google.com/file/d/1odl1Mid1-bXu7zTe7Qf58lM9EpQhdHJF/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33974
in KUNSTSTOFFE INTERNATIONAL > Vol. 110, N° 2 (02/2020) . - p. 8-13[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21623 - Périodique Bibliothèque principale Documentaires Disponible
[article]
Titre : Early beginnings of polyamide 6 and 66 Type de document : texte imprimé Année de publication : 2020 Article en page(s) : p. 90 Langues : Anglais (eng) Catégories : Chimie textile -- Histoire
Polyamide 6
Polyamide 66
Textiles et tissus -- HistoireIndex. décimale : 677.4 Textiles artificiels En ligne : https://drive.google.com/file/d/1rwmTjLkkSaoFy_1_LMBScZHmox9hT4qU/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=34558
in CHEMICAL FIBERS INTERNATIONAL > Vol. 70, N° 2/3 (09/2020) . - p. 90[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 22194 - Périodique Bibliothèque principale Documentaires Disponible Ecoulement anisotherme d'un polymère fondu dans une buse d'injection / L. Barré in LES CAHIERS DE RHEOLOGIE, Vol. XVII, N° 1 (10/2000)
[article]
Titre : Ecoulement anisotherme d'un polymère fondu dans une buse d'injection Type de document : texte imprimé Auteurs : L. Barré, Auteur ; Yves Bereaux, Auteur ; D. Graebling, Auteur Année de publication : 2000 Article en page(s) : p. 201-215 Note générale : Bibliogr. Langues : Français (fre) Catégories : Etat fondu (matériaux)
Matières plastiques -- Moulage par injection
Polyamide 66
Rhéologie
Simulation, Méthode de
ViscoélasticitéIndex. décimale : 532.05 Mécanique des fluides et des liquides - Dynamique (cinétique et cinématique) Résumé : Nous nous intéressons à l'écoulement et au transfert thermique d'un polymère fondu dans une buse durant la phase d'injection. Nous utilisons le logiciel POLYFLOW pour simuler l'écoulement du fluide Non-Newtonien modélisé par une loi de Bird-Carreau et par une loi viscoélastique de Giesekus. Le couplage thermo-mécanique est pris en compte à deux niveaux : d'une part, par la dissipation visqueuse dans l'équation d'énergie, d'autre part, par la thermodépendance des paramètres matériels (temps de relaxation et viscosité). Le contact thermique entre la paroi d'acier et le polymère fondu fait l'objet d'un calcul convection-conduction. Nous constatons que le régimes thermique et mécanique développés sont inaccessibles et que la paroi est quasi-adiabatique. Note de contenu : - SYNTHÈSE BIBLIOGRAPHIQUE : Modèles rhéologiques - Paramètres matériels et transfert de chaleur - Interface fluide/paroi - Calculs analytiques et numériques
- FORMULATION DU PROBLÈME : Buse d'injection - Équations gouvernantes - Polymère et modèle rhéologique - Conditions aux limites - Grandeurs caractéristiques et nombres adimensionnels
- RÉSULTATS NUMÉRIQUES : Maillage - Méthodes numériques - Profils de températures - Effet de la thermodépendancePermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=25826
in LES CAHIERS DE RHEOLOGIE > Vol. XVII, N° 1 (10/2000) . - p. 201-215[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21931 - Périodique Bibliothèque principale Documentaires Disponible Effect of welding parameters on microstructure and tensile strength of friction stir welded PA 6,6 joints / R. Nandhini in INTERNATIONAL POLYMER PROCESSING, Vol. XXXII, N° 4 (08/2017)
[article]
Titre : Effect of welding parameters on microstructure and tensile strength of friction stir welded PA 6,6 joints Type de document : texte imprimé Auteurs : R. Nandhini, Auteur ; M. Kesava Moorthy, Auteur ; Shanmugam Muthukumaran, Auteur Année de publication : 2017 Article en page(s) : p. 416-424 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Analyse de variance En statistique, l'analyse de la variance (terme souvent abrégé par le terme anglais ANOVA : ANalysis Of VAriance) est un ensemble de modèles statistiques utilisés pour vérifier si les moyennes des groupes proviennent d'une même population. Les groupes correspondent aux modalités d'une variable qualitative (p. ex. variable : traitement; modalités : programme d'entrainement sportif, suppléments alimentaires ; placebo) et les moyennes sont calculés à partir d'une variable continue (p. ex. gain musculaire).
Ce test s'applique lorsque l'on mesure une ou plusieurs variables explicatives catégorielles (appelées alors facteurs de variabilité, leurs différentes modalités étant parfois appelées "niveaux") qui ont de l'influence sur la loi d'une variable continue à expliquer. On parle d'analyse à un facteur lorsque l'analyse porte sur un modèle décrit par un seul facteur de variabilité, d'analyse à deux facteurs ou d'analyse multifactorielle sinon. (Wikipedia)
Diffractométrie de rayons X
Essais dynamiques
Matières plastiques -- Propriétés mécaniques
Matières plastiques -- Soudage
Microstructures
Polyamide 66
Thermogravimétrie
Traction (mécanique)Index. décimale : 668.4 Plastiques, vinyles Résumé : This paper deals with the work done on friction stir welding of thermoplastic material PA 6,6. A specially designed welding tool was used for this polymer. The major process parameters like tool rotational speed, feed rate were varied to understand the physical changes of the polymer and to carry out characterization studies. In this study, an attempt was made to optimize the process parameters by using L9 orthogonal array approach. ANOVA analysis was used to explore the effect of process parameters. Tensile testing was performed to analyze the joint strength. Thus, in new exploration of using polyamide 6,6 as base material, a maximum joint strength of 37 MPa has been achieved. Optimum combination of process parameters were found by using ANOVA studies. Microstructure of the friction stir welded joints using scanning electron microscopy was done. The X-ray diffraction and the thermogravimetric analysis were done to determine the degree of crystallinity and the level of degradation of the friction stir welded joints. Note de contenu : - EXPERIMENTAL METHODS : Materials - ANOVA analysis - Experimental design
- RESULTS AND DISCUSSION : Analyse of variance - SEM morphology - X-ray diffraction - Macroscopic examination - ThermogravimetricDOI : 10.3139/217.3296 En ligne : https://drive.google.com/file/d/156j_AsXM4oLKAHV1BagOArU9JKQhEHX3/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=28898
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXII, N° 4 (08/2017) . - p. 416-424[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19165 - Périodique Bibliothèque principale Documentaires Disponible Emana, le textile innovant aux propriétés thérapeutiques in TEXTILES A USAGES TECHNIQUES (TUT), N° 70 (12/2008 - 01-02/2009)
[article]
Titre : Emana, le textile innovant aux propriétés thérapeutiques Type de document : texte imprimé Année de publication : 2008 Article en page(s) : p. 23-24 Langues : Multilingue (mul) Catégories : Circulation sanguine
Polyamide 66
Textiles et tissus à usages médicaux
Textiles et tissus à usages techniquesIndex. décimale : 677.4 Textiles artificiels Résumé : Emana, fil textile de polyamide 66 incorpore un additif breveté qui améliore la circulation sanguine. L'effet est permanent et dure aussi longtemps que le vêtement lui-même. Des études scientifiques ont mis en évidence les bénéfices obtenus dans le processus de la fatigue musculaire et de l'élasticité de la peau lorsqu'on utilise des vêtements réalisés avec ces filaments textiles. Un large champ d'applications s'ouvre, principalement dans le sport et le segment de la lingerie et des sous-vêtements, en plus d'autres produits textiles qui aident à la réduction des signes de cellulite. Emana fait grand cas des propriétés du fil de polyamide : doux au toucher, facile d'entretien, résistant, élastique, facile à teindre, contribuant à une meilleure qualité de vie et certifié OEKO-TEX. Note de contenu : - Le principe
- Les bénéfices
- Le marché de la consommation
- Une équipe de travailPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=29524
in TEXTILES A USAGES TECHNIQUES (TUT) > N° 70 (12/2008 - 01-02/2009) . - p. 23-24[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 010975 - Périodique Bibliothèque principale Documentaires Disponible Enhanced infrared heating of thermoplastic composite sheets for thermoforming processes / M. Längauer in INTERNATIONAL POLYMER PROCESSING, Vol. 36, N° 1 (2021)
PermalinkÉtude expérimentale et numérique du comportement mécanique d’une liaison hybride métal/composite / Vladimir Gantchenko in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 26, N° 2 (04-05-06/2016)
PermalinkExtraction of polyphenolic dyes from henna, pomegranate rind, and Pterocarya fraxinifolia for nylon 6 dyeing / Izadyar Ebrahimi in COLORATION TECHNOLOGY, Vol. 132, N° 2 (04/2016)
PermalinkFabric dyeing with colorimetric pH-responsive colours / Roberta Peila in COLORATION TECHNOLOGY, Vol. 137, N° 2 (04/2021)
PermalinkPermalinkFaster process to safe battery enclosures / Karl Schnetzinger in KUNSTSTOFFE INTERNATIONAL, Vol. 112, N° 9 (2022)
PermalinkPermalinkFormulation freedom / Angela Smits in ADHESIVES & SEALANTS INDUSTRY (ASI), Vol. 18, N° 11 (11/2011)
PermalinkFrom fibreboard to composite honeycomb cores for custom-built doors / Greg Ringness in JEC COMPOSITES MAGAZINE, N° 113 (06/2017)
PermalinkFrom injection molding to additive manufacturing : / Andreas Wegner in KUNSTSTOFFE INTERNATIONAL, Vol. 111, N° 7 (2021)
PermalinkPermalinkPermalinkImproved process and component quality when using recycled materials / Stefan Kruppa in KUNSTSTOFFE INTERNATIONAL, Vol. 107, N° 11 (11/2017)
PermalinkImprovement of the dyeing and fastness properties of a naphthalimide fluorescent dye using poly(amidoamine) dendrimer / Mousa Sadeghi-Kiakhani in COLORATION TECHNOLOGY, Vol. 131, N° 2 (04/2015)
PermalinkImproving the colour fastness of dyed nylon-6 fabric by graft copolymerisation and curing of acrylic acid / Farzad Mohaddes in COLORATION TECHNOLOGY, Vol. 132, N° 3 (06/2016)
Permalink