Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Interfacial tensions, partition coefficients, and interfacial eelasticities : measures for emulsion stability ? / N. Buchavzov in TENSIDE, SURFACTANTS, DETERGENTS, Vol. 44, N° 4/2007 (08-09/2007)
[article]
Titre : Interfacial tensions, partition coefficients, and interfacial eelasticities : measures for emulsion stability ? Type de document : texte imprimé Auteurs : N. Buchavzov, Auteur ; F. Ravera, Auteur ; S. Hess, Auteur ; Y. Liu, Auteur ; U. Steinbrenner, Auteur ; C. Stubenrauch, Auteur Année de publication : 2007 Article en page(s) : p. 230-238 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Coefficient de partage (chimie)
Emulsions -- Stabilité
Rhéologie
Tension superficielleIndex. décimale : 668.1 Agents tensioactifs : savons, détergents Résumé : In this study the interfacial as well as the surface tensions, the partition coefficients Kp, the interfacial elasticities, and the stabilities of o/w-emulsions of the same systems were measured and compared to find a quantitative correlation which can help to control the emulsion stability. The systems in question contain water, paraffin oil and one of four non-ionic technical surfactants commonly used as emulsifiers. While a clear correlation between emulsion stability and equilibrium interfacial tension was found, the different emulsifying capacities cannot be explained by the partition coefficients Kp or the surface tension. However, combining the Kp results with the surface tension data allows us to estimate which emulsifier is more effective in solubilising a given amount of dispersed phase. Another method to classify emulsifiers is to carry out interfacial rheology measurements over a frequency range as broad as possible. Again a clear correlation between interfacial rheology and emulsifying capacity was found. This correlation, however, was restricted to surfactants of the same class. No correlation between interfacial rheology and emulsifying capacity could be found for emulsifiers of different molecular structure. DOI : 10.3139/113.100344 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3211
in TENSIDE, SURFACTANTS, DETERGENTS > Vol. 44, N° 4/2007 (08-09/2007) . - p. 230-238[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 008233 - Périodique Bibliothèque principale Documentaires Disponible Investigating changes in electrochemical properties when nano-silica is incorporated into an acrylic-based polyurethane clearcoat / Hamed Dastmalchian in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 9, N° 2 (03/2012)
[article]
Titre : Investigating changes in electrochemical properties when nano-silica is incorporated into an acrylic-based polyurethane clearcoat Type de document : texte imprimé Auteurs : Hamed Dastmalchian, Auteur ; Siamak Moradian, Auteur ; Mohammad Mehdi Jalili, Auteur ; Seyed Mojtaba Mirabedini, Auteur Année de publication : 2012 Article en page(s) : p. 195-201 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Nanoparticules
Nanotechnologie
Polyacryliques
Polyols
Polyuréthanes
Rhéologie
SiliceLa silice est la forme naturelle du dioxyde de silicium (SiO2) qui entre dans la composition de nombreux minéraux.
La silice existe à l'état libre sous différentes formes cristallines ou amorphes et à l'état combiné dans les silicates, les groupes SiO2 étant alors liés à d'autres atomes (Al : Aluminium, Fe : Fer, Mg : Magnésium, Ca : Calcium, Na : Sodium, K : Potassium...).
Les silicates sont les constituants principaux du manteau et de l'écorce terrestre. La silice libre est également très abondante dans la nature, sous forme de quartz, de calcédoine et de terre de diatomée. La silice représente 60,6 % de la masse de la croûte terrestre continentale.
Spectroscopie d'impédance électrochimique
Tension superficielle
Vernis -- AdditifsIndex. décimale : 667.9 Revêtements et enduits Résumé : Two different types of nano-silica (i.e., hydrophilic Aerosil 200 and hydrophobic Aerosil R805) were employed in the preparation of 2-pack acrylic polyol polyurethane nano-coatings so that the electrochemical properties of the resultant coatings could be investigated. Electrochemical impedance spectroscopy was used to evaluate the corrosion performances of such nano-coatings applied onto mild steel substrates that were immersed in 3.5% (w/w) NaCl solutions. It was observed coatings that contained nano-silica increased the barrier properties of the binder, as well as the coatings’ electrochemical resistance compared with pure polyurethane coatings. The surface tension of pure polyurethane was measured by a tensiometer. Rheological properties were also determined at various shear rates by a rotaviscometer. Results showed that the surface tension of hydrophobic nano-silica is very close to the pure polyurethane matrix, giving the better compatibility of the two. This was further confirmed by transmission electron microscopy and by the fact that the hydrophobically filled nano-silica coatings showed shear thinning behavior in the fluid state. Also observed was better corrosion performance of the resultant hydrophobic nano-coatings compared to coatings embedded with hydrophilic nano-silica. Note de contenu : - EXPERIMENTAL METHODS : Raw materials - Preparation of nano-coatings - Tensiometrical properties - Morphological analysis - Rheological studies - Electrochemical behavior
- RESULTS AND DISCUSSION : Electrochemical behavior - Morphological observations - Rheological behavior - Electrochemical studiesDOI : 10.1007/s11998-009-9222-0 En ligne : https://link.springer.com/content/pdf/10.1007/s11998-009-9222-0.pdf?pdf=button Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=14372
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 9, N° 2 (03/2012) . - p. 195-201[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 14096 - Périodique Bibliothèque principale Documentaires Disponible Investigation of interfacial instabilities with a two-layer slide coating process / Cornelia K. Buerkin in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 14, N° 5 (09/2017)
[article]
Titre : Investigation of interfacial instabilities with a two-layer slide coating process Type de document : texte imprimé Auteurs : Cornelia K. Buerkin, Auteur ; Ike de Vries, Auteur ; Sebastian M. Raupp, Auteur ; Philip Scharfer, Auteur ; Wilhelm Schabel, Auteur ; Pim Groen, Auteur Année de publication : 2017 Article en page(s) : p. 991-1001 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Cyclopentanone
DiméthylbenzèneLe xylène ou diméthylbenzène est un groupe d'hydrocarbures aromatiques dérivés méthylés du benzène. Il est représenté par trois isomères structuraux : 1,2-diméthylbenzène, 1,3-diméthylbenzène et 1,4-diméthylbenzène (appelés respectivement ortho-diméthylbenzène, méta-diméthylbenzène et para-diméthylbenzène). Le xylène technique est un mélange des trois isomères, de composition voisine de méta- (60 %), ortho- (10-25 %) et para- (10-25 %). Tout comme pour le benzène, la structure du xylène est plane. C'est un composé aromatique, et les électrons formant les liaisons π du cycle sont délocalisés, ce qui entraîne une stabilité importante de la structure.
PROPRIETES PHYSICO-CHIMIQUES : Le xylène est un liquide incolore, d'odeur agréable et très inflammable. Il est naturellement présent dans le pétrole et le goudron de houille, et se forme durant les feux de forêts. Les propriétés chimiques diffèrent peu d'un isomère à l'autre. La température de fusion est comprise entre -47,87 °C (m-Xylène) et 13,26 °C (p-Xylène). La température d'ébullition est voisine de 140 °C pour tous les isomères. La densité est de 0,87 (le composé est plus léger que l'eau). L'odeur du xylène devient détectable pour des concentrations de l'ordre de 0,08 à 3,7 ppm, et le goût est apparent dans l'eau pour des concentrations de l'ordre de 0,53 à 1,8 ppm.
PRODUCTION ET UTILISATION : Le xylène est produit à partir du pétrole dans l'industrie pétrochimique. En termes de volume, c'est l'un des 30 composés chimiques les plus produits aux USA (environ 450 000 tonnes par an). Il est utilisé comme solvant, notamment en tant que céruménolytique. Il est aussi utilisé par les industries de l'impression, du caoutchouc et du cuir. Il est employé comme réactif de départ pour la production d'acide téréphtalique, utilisé comme monomère pour la production de polymères de type téréphtalate. Le xylène est également utilisé pour le nettoyage, comme pesticide, utilisé aussi en parasitologie dans la méthode de KOHN pour vérifier la bonne déshydratation de frottis de selle, comme diluant pour la peinture ainsi que dans la peinture et les vernis. Il est présent en faibles quantités dans les carburants pour l'aviation ainsi que dans l'essence (voir l'article « Pouvoir calorifique »). En présence de réactifs oxydants, comme le permanganate de potassium KMnO4, le groupement méthyle peut être oxydé jusqu'à former un acide carboxylique. Lorsque les deux groupements méthyle sont oxydés, le o-xylène forme l'acide phtalique et le p-xylène l'acide téréphtalique.
Electronique -- Matériaux
Ethylène glycol
Polyglycol monoéthyl éther acétate
Propylène glycol
Revêtements multicouches
Revêtements organiques
Slide coating
Tension superficielleIndex. décimale : 667.9 Revêtements et enduits Résumé : Organic electronics have been thoroughly investigated due to their broad application potential, ranging from light-emitting diodes to photovoltaics. The processing of organic electronics is trending from vacuum toward wet chemical deposition, which allows fast low-cost mass production of devices with scalable dimension. One of the current challenges of wet film processing is the redissolution of already dried active materials when applying a liquid top layer. Further, increasing overall process efficiency by coating multiple liquid layers in one step raises such challenges as liquid–liquid mixing or dewetting. This article describes the experimental investigation of these instabilities for two-layer flows with organic solvents. A modified slide coating device was chosen where an extended plate after the slot exit allows prolonged observation of the flow while it travels down the plate. During experimentation, stable and unstable two-layer flows as well as different types of instabilities were detected. The key finding is a correlation of flow stability with the spreading coefficient, a combined measure of surface and interfacial tensions. Focusing on fluid properties, this paper succeeds in defining a three-dimensional stability window for a dual-layer flow. Note de contenu : - Theoretical background : flow down an inclinded plane
- Experimental design, setup and solvent selection
- Experimental results : influence of surface and interfacial tension
- Experimental results : influence of viscosity
- Experimental results : miscible fluids with similar viscositiesDOI : 10.1007/s11998-017-9961-2 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-017-9961-2.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=29128
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 14, N° 5 (09/2017) . - p. 991-1001[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 19230 - Périodique Bibliothèque principale Documentaires Disponible Leather finishing : Preparation and application of cationic organosilicone/polyurethane micro-emulsion / Shen Yiding in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC), Vol. 91, N° 3 (05-06/2007)
[article]
Titre : Leather finishing : Preparation and application of cationic organosilicone/polyurethane micro-emulsion Type de document : texte imprimé Auteurs : Shen Yiding, Auteur ; Haihua Wang, Auteur ; Guiqiang Fei, Auteur ; Fan Xiaojing, Auteur Année de publication : 2007 Article en page(s) : p. 108-115 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Analyse morphologique
Analyse thermique
Caractérisation
Cuirs et peaux -- Finition
Cuirs et peaux -- Propriétés mécaniques
Essais de résilience
Granulométrie
Microémulsions
Organosilicones
Polymères -- Analyse
Polyuréthanes
Résistance à l'abrasion
Rhéologie
Tension superficielleIndex. décimale : 675 Technologie du cuir et de la fourrure Résumé : Using a catalyst and cosolvent, hydroxyl-terminated polydimethylsiloxane (HPMS) based polyurethane (PU) micro-emulsion (WPU/HPMS) derived from isophorone isocyanate (IPDI) and poly- tetramethylene glycol (PTMG) was synthesised by self-emulsifying copolymerization. The polymer was then used in leather finishing.
The structure, rheological behavior, morphology and heat performance were characterized by Fourier transform infared spectroscopy (FT-IR), 1H nuclear magnetic resonance (1H NMR), gel permeation chromatography (GPC), light scattering (LS), transmission electron microscopy (TEM), interfacial tension (IT), wide-angle X-ray diffraction (WAXD), differential scanning calorimeter (DSC) and thermogravimetry (TG).
The results reveal that WPU/HPMS micro-emulsion is endowed with low surface tension, pseudoplasticity and thixotropy, which are beneficial to the properties of coating. DSC and TG diagrams also reveal that the application range of product was enlarged. Furthermore, the WPU/HPMS micro-emulsion was found to be a good finishing agent, endowing leather with a brightness, softness, plump/full and smooth surface, and thus improving the quality of leather.Note de contenu : - EXPERIMENTAL PROCEDURES : Materials - Synthesis of WPU/HPMS micro-emulsion
- POLYMER ANALYSIS
- FINISHED LEATHER PROPERTIES
- RESULTS AND DISCUSSION : FT-IR analysis - H NMR analysis - Particle size and morphology - Surface tension of the emulsion - Rheological behavior of PU/HPMS micro-emulsion - Thermal analysis
- APPLICATION OF WPU/HPMS MICRO-EMULSION IN LEATHER FINISHING : Leather finishing process - Mechanical properties
- Table 1 : Chemical shift of various protons
- Table 2 : Surface tension of WPU and WPU/HPMS micro emulsions
- Table 3 : The n, k values for WPU and WPU/HPMs micro-emulsions
- Table 4 : Experimental results of DSC for WPU and WPU/HPMS
- Table 5 : The effect of HPMS on the heat resistance of waterborne WPU cast
- Table 6 : Physical and chemical indexes of leather after finishing
- Table 7 : Contact angles of the leather surface
- Table 8 : Results of dry rubbing fastness
- Table 9 : Results of wet rubbing fastness
- Table 10 : Flex resistance of finishing leatherEn ligne : https://drive.google.com/file/d/1ZThmNSkOEZ-xvm6Vb5hiiI3yrvChyyYO/view?usp=share [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39028
in JOURNAL OF THE SOCIETY OF LEATHER TECHNOLOGISTS & CHEMISTS (JSLTC) > Vol. 91, N° 3 (05-06/2007) . - p. 108-115[article]Leveling of a model paint film with ayield stress / D. E. Weidner in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 17, N° 4 (07/2020)
[article]
Titre : Leveling of a model paint film with ayield stress Type de document : texte imprimé Auteurs : D. E. Weidner, Auteur Année de publication : 2020 Article en page(s) : p. 851-863 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Elasticité
Modèles numériques
Revêtements:Peinture
Tension superficielleIndex. décimale : 667.9 Revêtements et enduits Résumé : The coating dynamics of a drying paint film with a yield stress is studied. The liquid is modeled as a binary mixture with one volatile component, solvent, and one nonvolatile component, resin. When the solvent has a different surface tension than the resin, solvent evaporation can lead to the creation of surface tension gradients which can potentially overcome the yield stress and dramatically affect the flow history. Using the lubrication approximations to derive the flux of the liquid film parallel to the substrate, we find that the presence of the yield stress causes several distinct flow regimes. The total flux of each of these regimes is summed, and using the continuity equation we derive an evolution equation giving the height of the free surface as a function of the distance along the substrate and time. The resulting equations are discretized and solved numerically using finite differences. High order derivative is treated implicitly, allowing for large time steps and reducing the computational requirements. We find that the presence of a yield stress greatly affects the leveling behavior of the coating. Critical yield stresses exist that can cause maximal leveling of the coating film. Note de contenu : - Derivation of equations
- Nondimensionalization
- Numerical aspectsDOI : https://doi.org/10.1007/s11998-019-00260-z En ligne : https://link.springer.com/content/pdf/10.1007/s11998-019-00260-z.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=34375
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 17, N° 4 (07/2020) . - p. 851-863[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21864 - Périodique Bibliothèque principale Documentaires Disponible Limitations of classical methods for measuring surface tension in visco-elastic liquids / A. Bochkarev in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 7, N° 3 (05/2010)
PermalinkLiquid film coating of small molecule OLEDs / Katharina Peters in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 11, N° 1 (01/2014)
PermalinkLowering the tension / Vicky James in POLYMERS PAINT COLOUR JOURNAL - PPCJ, Vol. 197, N° 4510 (03/2007)
PermalinkMatériaux thermoplastiques à base de biopolymère pour leur impression 3D par dépôt de fil fondu / Laurent Chaunier in RHEOLOGIE, Vol. 38 (12/2020)
PermalinkModélisation et simulation numérique de l’étalement goutte fluide sur un plan horizontal / H. Alla in RHEOLOGIE, Vol. 6 (10/2004)
PermalinkMould release potential of polydimethylsiloxane coatings using photoinitiated polymerisation / David P. Dworak in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 89, B2 (06/2006)
PermalinkMultifunctional superwetting agent for coating applications / Vimal Saini in POLYMERS PAINT COLOUR JOURNAL - PPCJ, Vol. 209, N° 4657 (12/2019)
PermalinkNanoclay migration and the rheological response of PBAT-LDPE blends / M. Nofar in INTERNATIONAL POLYMER PROCESSING, Vol. 36, N° 3 (2021)
PermalinkNatural dye–surfactant interactions: thermodynamic and surface parameters in COLORATION TECHNOLOGY, Vol. 128, N° 4 (2012)
PermalinkNew additive to eliminate pinholes for water-based coating formulations / Jim Reader in COATINGS TECH, Vol. 18, N° 3 (03/2021)
PermalinkNew additive to enhance surface cleanability / Gururaj Moharir in PAINTINDIA, Vol. LVII, N° 6 (06/2007)
PermalinkNew surfactant technology for waterborne coatings and inks / William Dougherty in EUROPEAN COATINGS JOURNAL (ECJ), N° 10/95 (10/1995)
PermalinkPermalinkNonionic short-chain fluorinated surfactants in the fatliquoring of chrome-tanned goat skin / Yichao Shen in JOURNAL OF THE AMERICAN LEATHER CHEMISTS ASSOCIATION (JALCA), Vol. CXV, N° 7 (07/2020)
PermalinkA novel synthesis of anionic heterogemini surfactants containing COOH, SO3H and PO(OH)2 headgroups from corynomicolic acid and its derivatives / Tokuzo Kawase in TENSIDE, SURFACTANTS, DETERGENTS, Vol. 48, N° 6 (11-12/2011)
PermalinkA novel waterborne fluorinated polyurethane–acrylate film for ultraviolet blocking and antiprotein fouling in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 18, N° 5 (09/2021)
PermalinkPermalinkOptimizing interactions between soluble silk fibroin and capryl glucoside for design of a natural and high-performance co-surfactant system in INTERNATIONAL JOURNAL OF COSMETIC SCIENCE, Vol. 43, N° 1 (02/2021)
PermalinkOrange peel formation due to surface tension-driven flows within drying paint films / N. Saranjam in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 13, N° 3 (05/2016)
PermalinkPartially fluorinated automotive coatings / William Graham in EUROPEAN COATINGS JOURNAL (ECJ), N° 5/97 (05/1997)
Permalink