Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Case studies : Low cost, high-strength, large carbon foam tooling / Rick Lucas in SAMPE JOURNAL, Vol. 45, N° 1 (01-02/2009)
[article]
Titre : Case studies : Low cost, high-strength, large carbon foam tooling Type de document : texte imprimé Auteurs : Rick Lucas, Auteur ; Harry Danford, Auteur Année de publication : 2009 Article en page(s) : p. 20-28 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Anticorrosion
Carbone
Composites
Dilatation (thermodynamique)
Mousses (matériaux) -- Applications industrielles
Mousses plastiques
UsinageIndex. décimale : 668.9 Polymères Résumé : A new carbon foam system has been developed that results in a low-cost, high-strength material that has been proving attractive for creation of tooling for composite parts. Composites are stronger, lighter, and less subject to corrosion and fatigue than materials that currently used for fabrication of advanced structures. Tools to manufacture these composite parts must be rigid, durable and able to offer a coefficient of thermal expansion (CTE) closely matching that of the composites. Current technology makes it difficult to match the CTE of a composite part in the curing cycle with anything other than a carbon composite or a nickel iron alloy such as invar.
Fabrication of metallic tooling requires many expensive stages of long duration with a large infrastructure investment. Carbon fiber reinforced polymer resin composite tooling has a shorter lead-time but limited production use because of its low cost, light weight, machinability, vacuum integrity, and compatibility with a wide range of curing processes. Large-scale tooling case studies will be presented detailing carbon foam's potential for tooling applications.Note de contenu : - Carbon foam
- Carbon foam tooling
- Rapid prototype/Short production run tooling
- Tool life
- Fabrication techniques
- Final preparation and processing
- Large scale toolingPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3376
in SAMPE JOURNAL > Vol. 45, N° 1 (01-02/2009) . - p. 20-28[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 011005 - Périodique Bibliothèque principale Documentaires Disponible Cementitious polyurethane flooring - an intelligent solution / Shyam Nagpure in PAINTINDIA, Vol. LXVI, N° 8 (08/2016)
[article]
Titre : Cementitious polyurethane flooring - an intelligent solution Type de document : texte imprimé Auteurs : Shyam Nagpure, Auteur ; Shekhar Tambe, Auteur ; Nitin Bendale, Auteur ; Ramakant Choudhari, Auteur Année de publication : 2016 Article en page(s) : p. 57-59 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Adhésion
Composites
Dureté (matériaux)
Etalement spontané (revêtement)
Matériaux cimentaires
Polyuréthanes
Résistance thermique
Revêtements -- Propriétés mécaniques
Revêtements de sols:Peinture de sols
ThermogravimétrieIndex. décimale : 667.9 Revêtements et enduits Résumé : In the past major focus during construction and maintenance of industrial plant was primarily on process equipement and the material of construction. The concrete structure and flooring was considered less critical. However in current scenario, floorings in plant are integral part of many operations. Limitations of concrete flooring are dust accumulation, porosity, cracks, alkalinity, microbial growth, laitance, efflorescence, and poor chemical resistance. To overcome these limitations and provide a sound surface, various protective coatings are in use. Protective coating in majority are self-levelling floor coatings based on epoxy and polyurethane chemistry. Self-levelling epoxy flooring is known for its high adhesion, hardness and initial gloss, however, poor in flexibility, scratch resistance and gloss retention. The advantage of polyurethane coating over epoxy coating is because of its flexibility, scratch resistance and durability. Note de contenu : - MARKET LANDSCAPE
- CEMENTITIOUS POLYURETHANE (PU)FLOORING
- DESIGN TYPICAL PU FLOORING
- PERFORMANCE PROPERTIES : Hardness - Thermal shock resistance - Thermo Gravimetric analysis (TGA) - Adhesion over green concrete - Slip resistance
- MECHANICAL PROPERTIESEn ligne : https://drive.google.com/file/d/1H-VpexYGjkX3hTtEfC2khNmgolQq-rL5/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=27293
in PAINTINDIA > Vol. LXVI, N° 8 (08/2016) . - p. 57-59[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 18497 - Périodique Bibliothèque principale Documentaires Disponible
[article]
Titre : Certified composite repair system for pipelines Type de document : texte imprimé Année de publication : 2014 Article en page(s) : p. 42 Langues : Anglais (eng) Catégories : Composites
Pipelines -- Entretien et réparationsIndex. décimale : 668.4 Plastiques, vinyles Résumé : Henkel presented its innovative solutions for the maintenance and repair of industrial facilities, equipment and components for the first time at the 2014 ONS (Offshore Northern Seas) international trade fair in Stavanger, Norway. Dedicated to the oil, gas and energy industry, the company launched a certified composite repair system that can be used to tailor pipeline repairs and protection to increase pipe lifetime. Note de contenu : - Eliminating costly downtime
- Increasing the lifetime of steel pipesEn ligne : https://drive.google.com/file/d/1Ctu8EfeGyV61fA7xOdcmsAE5UP5TiuBB/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=23025
in JEC COMPOSITES MAGAZINE > N° 92 (10-11/2014) . - p. 42[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 16573 - Périodique Bibliothèque principale Documentaires Disponible Changing nature of wood products - What does it mean for coatings and finish performance / Charles Jourdain in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 71, N° 890 (03/1999)
[article]
Titre : Changing nature of wood products - What does it mean for coatings and finish performance Type de document : texte imprimé Auteurs : Charles Jourdain, Auteur ; Jack Dwyer, Auteur ; Keith Kersell, Auteur ; Douglas Mall, Auteur ; Ken McClelland, Auteur ; Robert Springate, Auteur ; Sam Williams, Auteur Année de publication : 1999 Article en page(s) : p. 61-66 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Assemblages (technologie)
Composites
Panneaux de fibres
Panneaux de particules
Revêtements:PeintureIndex. décimale : 667.9 Revêtements et enduits Résumé : As the fundamental nature of North American forest has changed over the past 200 years, so have the properties of the building products derived from those forests. Smaller diameter secondand third growth trees yield lumber with higher percentages of knots and sapwood and less of the clear fine grain lumber traditionally used for architectural applications. Many of the current recommendations for finishing exterior wood products are based upon dated information. The more knotty solid wood products used today may have coarser grain and be predominantly flat-grained. Flat-grained lumber is more prone to grain raising and dimensional change. Saw-textured surfaces decrease the potential for grain raising and they enhance finish performance. Saw-textured knotty flat-grained wood products may perform better if they are finished with penetrating finishes (semitransparent stain) rather than with film-forming finishes (paints). Semitransparent stains and other types of penetrating finishes do not peel and tend to be less likely to show knot or extractives bleed. Film-forming finishes may also be used on knotty saw-textured flat-grained surfaces, however discoloration because of bleed-through at the knots continues to be a challenge, particularly with light-colored finishes.
Use of different wood species, flat-grained knotty wood, and composites may require some changes in finishing practice and more careful selection of products for specific uses. For example, if a white painted look is desired, it may be better to use a paper-overlaid product to eliminate problems with knot bleed than to try to seal the knots using shellac. If finger-jointed lumber is used, extra care may be required to assure that the finish can adequately block the extractives. Sealing and painting the edges of composites is necessary to assure good performance. Paper-overlaid products give a good surface for painting.
Advances in finger-jointing and factory prefinishing will add to the performance of modern wood products. In the coming decade, the transition to lumber from rapidly grown intensively managed forests will continue. New species and composites will become more available in the marketplace. Much of the burden for assuring the compatibility of finishes with new wood products will probably rest with the woatings manufacturers and their suppliers. The technology of paints and other finishes and the protocols for testing finishes must advance to keep pace with the changes in the substrates.Note de contenu : - WOOD PROPERTIES
- EXTERIOR WOOD PRODUCTS : Architectural products and species - Imported wood species - Silvicultural practices to enhance wood quality - Lumber grades and quality - Flat-grained siding and lumber-effect on finishing - Wood/wood composites - Wood/plastic composites - Paper-overlaid products - Fiberboard
- PAINTING GUIDELINES : Flat-grained solid lumber and siding - Finger-jointed lumber and siding - Plywood - Wood/wood composites - Wood/plastic composites - Paper-overlaid products - Fiberboard - Factory priming and finishingEn ligne : http://www.fpl.fs.fed.us/documnts/pdf1999/jourd99a.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=18038
in JOURNAL OF COATINGS TECHNOLOGY (JCT) > Vol. 71, N° 890 (03/1999) . - p. 61-66[article]Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 009604 - Périodique Bibliothèque principale Documentaires Exclu du prêt
[article]
Titre : Chimie du bore et du silicium : Application aux matériaux composites céramiques pour utilisation à haute température Type de document : texte imprimé Auteurs : Roger Naslain, Auteur ; Alain Guette, Auteur Année de publication : 2006 Article en page(s) : p. 19-25 Note générale : Bibliogr. Langues : Français (fre) Catégories : Bore
Carbone
Chimie minérale
Composites
Hautes températures
Matériaux céramiques
SiliciumIndex. décimale : 546 Chimie minérale Résumé : Grâce à son four à arc électrique, Henri Moissan a été l'un des tout premiers chercheurs à avoir synthétisé les borures, carbures, nitrures et siliciures réfractaires, dont SiC, B4C et BN. Ces matériaux sont les constituants des composites fibreux à matrice céramique (C/C, C/SiC et SiC/SiC), développés soixante ans plus tard pour des applications structurales à haute température. Toutefois, les composites à matrice céramique (CMC) sont élaborés à température plus modérée pour ménager les fibres. Ils sont constitués d'une architecture fibreuse céramique densifiée, par exemple par infiltration chimique en phase vapeur, par une matrice céramique, les deux constituants étant couplés par l'intermédiaire d'un matériau d'interphase (carbone graphitique ou BN-hexagonal) dont le rôle est de dévier les fissures matricielles et d'éviter la rupture prématurée des fibres. Les CMC sont des céramiques tenaces et résistant aux chocs. En revanche, ils sont sensibles à l'oxydation. On améliore leur résistance en atmosphère oxydante en utilisant un revêtement ou mieux, une matrice autocicatrisante multicouche comportant des déviateurs de fissures et des formateurs d'oxyde fluide cicatrisant. En ligne : https://www.lactualitechimique.org/Chimie-du-bore-et-du-silicium-application-aux [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3939
in L'ACTUALITE CHIMIQUE > N° 301-302 (10-11/2006) . - p. 19-25[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 005749 - Périodique Bibliothèque principale Documentaires Disponible La chimie en Région Midi-Pyrénées (dossier) / Société Française de Chimie in L'ACTUALITE CHIMIQUE, N° 392 (01/2015)
PermalinkLa chimie et le sport / Minh-Thu Dinh-Audouin / Les Ulis : EDP Sciences (2011)
PermalinkChitosan based antibacterial composite materials for leather industry : a review / Linlin Yuan in JOURNAL OF LEATHER SCIENCE AND ENGINEERING, Vol. 3 (Année 2021)
PermalinkPermalinkCleaning with TRI in a total vacuum / Markus Mitschele in INTERNATIONAL SURFACE TECHNOLOGY (IST), N° 2/2010 (2010)
PermalinkCoatings for solar panel / Shibajit Mukherjee in PAINTINDIA, Vol. LXIII, N° 11 (11/2013)
PermalinkA comparative study on protective properties of electrosynthesized poly(pyrrole)/poly(N-methylpyrrole), poly(pyrrole)/poly(N-phenylpyrrole), poly(pyrrole)/poly(N-methoxyphenylpyrrole) composite coatings / Berrin Duran in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 10, N° 6 (11/2013)
PermalinkComportement et endommagement dynamique multi-échelle de composites SMC-R26 / Zouhaier Jendli in MATERIAUX & TECHNIQUES, N° 3-4 (03-04/2005)
PermalinkComportement en flexion 3-points d'un matériau composite instrumenté par capteur à réseaux de Bragg / Aurélie Cordelle in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 23, N° 1 (01-02-03-04/2013)
PermalinkComposite aerostructure development in high-performance entreprises / John W. O'Connor in JEC COMPOSITES MAGAZINE, N° 92 (10-11/2014)
PermalinkComposite assembly solutions / Murray Akerman in ADHESIVES & SEALANTS INDUSTRY (ASI), Vol. 19, N° 11 (11/2012)
PermalinkComposite design software - Gaining currency within the wind industry / Olivier Guillermin in SAMPE JOURNAL, Vol. 46, N° 6 (11-12/2010)
PermalinkComposite films integrate lighting and control sensors in decorative surfaces / Reinhard Bauer in KUNSTSTOFFE INTERNATIONAL, Vol. 105, N° 1-2 (01-02/2015)
PermalinkComposite laminate for boat structures in JEC COMPOSITES MAGAZINE, N° 75 (08-09/2012)
PermalinkComposite manufacturing / Avner Ben-Bassat in JEC COMPOSITES MAGAZINE, N° 96 (04/2015)
Permalink