Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Orange peel formation due to surface tension-driven flows within drying paint films / N. Saranjam in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 13, N° 3 (05/2016)
[article]
Titre : Orange peel formation due to surface tension-driven flows within drying paint films Type de document : texte imprimé Auteurs : N. Saranjam, Auteur ; S. Chandra, Auteur ; Javad Mostaghimi, Auteur ; H. Fan, Auteur ; J. Simmer, Auteur Année de publication : 2016 Article en page(s) : p. 413-426 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Acier inoxydable
Métaux -- Revêtements:Métaux -- Peinture
Revêtement en phase solvant:Peinture en phase solvant
Revêtements -- Défauts:Peinture -- Défauts
Tension superficielle
Transfert de masseIndex. décimale : 667.9 Revêtements et enduits Résumé : Paint films with uniform thicknesses ranging from 150 to 820 μm were applied on stainless steel substrates using a model paint consisting of a resin dissolved in butanol and the test samples were cured in a natural convection oven at a temperature of 140°C. Photographs of the paint surface were taken during drying, and the weight loss was measured. Cellular structures appeared on the paint surface, induced by surface tension-driven flows due to solvent concentration variations. For thin films (<500 µm), the patterns disappeared in a few minutes and the dried paint surface was smooth, while for thicker paint films, wave-like structures remained on the hardened paint layer, creating an uneven surface. An analytical solution of the mass-diffusion equation was used to model solvent evaporation from the paint film and to calculate the concentration gradient and surface tension variations in the paint films. In thin films, all the solvent was depleted, and surface tension gradients disappeared before curing was complete, allowing the surface to become smooth. In thicker films, concentration gradients that drove cellular flows persisted until the paint dried, leaving orange peel on the surface. DOI : 10.1007/s11998-015-9752-6 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-015-9752-6.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=26283
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 13, N° 3 (05/2016) . - p. 413-426[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 18071 - Périodique Bibliothèque principale Documentaires Disponible painting bolted bridge connections / Kenneth A. Trimber in JOURNAL OF PROTECTIVE COATINGS & LININGS (JPCL), Vol. 33, N° 5 (05/2016)
[article]
Titre : painting bolted bridge connections Type de document : texte imprimé Auteurs : Kenneth A. Trimber, Auteur Année de publication : 2016 Article en page(s) : p. 34-43 Langues : Américain (ame) Catégories : Acier L'acier est un alliage métallique utilisé dans les domaines de la construction métallique et de la construction mécanique.
L'acier est constitué d'au moins deux éléments, le fer, très majoritaire, et le carbone, dans des proportions comprises entre 0,02 % et 2 % en masse1.
C'est essentiellement la teneur en carbone qui confère à l'alliage les propriétés du métal qu'on appelle "acier". Il existe d’autres métaux à base de fer qui ne sont pas des aciers comme les fontes et les ferronickels par exemple.
Assemblages à boulons
Essais dynamiques
Fluage
Frottements (mécanique)
Métaux -- Revêtements:Métaux -- Peinture
Ponts métalliques -- Revêtements protecteursIndex. décimale : 667.6 Peintures Résumé : High-strength bolts have been used to assemble steel structures for over 60 years, supported by research conducted by the Research Council on Riveted and Bolted Structural Joints (RCRBSJ). RCRBSJ was founded in 1947 but is now known as the Research Council on Structural Connections (RCSC). Despite the long history of use, there is still confusion when it comes to painting faying surfaces, bolt holes and fasteners. This article will attempt to clear up some of the confusion and provide items to consider when designing and painting bolted connections. Note de contenu : - Testing of coatings for slip-critical joints
- Coefficient of friction (COF) testing
- Tension creep testing
- Interpretation of slip coefficient and tension creep results
- Painting of bolt holes
- Cleaning and painting of fasteners : Black bolts - Galvanized boltsPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=26837
in JOURNAL OF PROTECTIVE COATINGS & LININGS (JPCL) > Vol. 33, N° 5 (05/2016) . - p. 34-43[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 18124 - Périodique Bibliothèque principale Documentaires Disponible Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Part 1 : Coatings prepared from coating - Norme EN 12206-1 / Comité Européen de Normalisation / Bruxelles [Belgique] : CEN (2004)
Titre : Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Part 1 : Coatings prepared from coating - Norme EN 12206-1 Type de document : texte imprimé Auteurs : Comité Européen de Normalisation, Auteur Editeur : Bruxelles [Belgique] : CEN Année de publication : 2004 Importance : 25 p. Présentation : ill. Format : 30 cm Note générale : Annexes - Bibliogr. Langues : Anglais (eng) Catégories : Aluminium L'aluminium est un élément chimique, de symbole Al et de numéro atomique 13. C’est un métal pauvre, malléable, de couleur argent, qui est remarquable pour sa résistance à l’oxydation13 et sa faible densité. C'est le métal le plus abondant de l'écorce terrestre et le troisième élément le plus abondant après l'oxygène et le silicium ; il représente en moyenne 8 % de la masse des matériaux de la surface solide de notre planète. L'aluminium est trop réactif pour exister à l'état natif dans le milieu naturel : on le trouve au contraire sous forme combinée dans plus de 270 minéraux différents, son minerai principal étant la bauxite, où il est présent sous forme d’oxyde hydraté dont on extrait l’alumine. Il peut aussi être extrait de la néphéline, de la leucite, de la sillimanite, de l'andalousite et de la muscovite.
L'aluminium métallique est très oxydable, mais est immédiatement passivé par une fine couche d'alumine Al2O3 imperméable de quelques micromètres d'épaisseur qui protège la masse métallique de la corrosion. On parle de protection cinétique, par opposition à une protection thermodynamique, car l’aluminium reste en tout état de cause très sensible à l'oxydation. Cette résistance à la corrosion et sa remarquable légèreté en ont fait un matériau très utilisé industriellement.
L'aluminium est un produit industriel important, sous forme pure ou alliée, notamment dans l'aéronautique, les transports et la construction. Sa nature réactive en fait également un catalyseur et un additif dans l'industrie chimique ; il est ainsi utilisé pour accroître la puissance explosive du nitrate d'ammonium.
Métaux -- Revêtements:Métaux -- Peinture
Revêtements -- Normes:Peinture -- Normes
Revêtements en bâtiment:Peinture en bâtimentIndex. décimale : 667.6 Peintures Résumé : This Part of EN 12206 specifies requirements and the corresponding methods of test relating to the organic coating of aluminium and aluminium alloy extrusions, sheet and preformed sections for architectural purposes, using coating powders. It also describes :
a) the pretreatment of the substrate prior to the coating process ;
b) the coating powder ;
c) the coating process ;
d) the final product.
Each item is dealt with separately in this Part of EN 12206 so that any interested party can ensure compliance appropriate to its area of responsibility.Classification ICS : 87.040 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=32782 Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 20862 EN 12206-1 Norme Bibliothèque principale Documentaires Disponible
[article]
Titre : Patterns of roughness : How surface structure evolves from substrate to topcoat Type de document : texte imprimé Auteurs : Michael Osterhold, Auteur Année de publication : 2016 Article en page(s) : p. 44-48 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Automobiles -- Revêtements:Automobiles -- Peinture
Brillance (optique)
Caractérisation
Métaux -- Revêtements:Métaux -- Peinture
Réticulation (polymérisation)
Surfaces -- AnalyseIndex. décimale : 667.9 Revêtements et enduits Résumé : The visual impression of a painted surface is influenced by its surface structure (levelling, waviness, orange peel etc.) Two different measuring methods have become established in the automotive and paint industry. Some comparisons between these methods and the effects of successive paint layers on surface structure are reported. Note de contenu : - Scope of mechanical surface characterisation
- Optical surface characterisation
- Paint application and curing effects on metal
- Matching the finish of metal substrates on plastics
- Medium gloss surfaces : variation of substrate
- The broader picture summarisedEn ligne : https://drive.google.com/file/d/117R5AGa1wpyTCyEtNa9HXq229KMRnucy/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=26727
in EUROPEAN COATINGS JOURNAL (ECJ) > N° 7-8 (07-08/2016) . - p. 44-48[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 18224 - Périodique Bibliothèque principale Documentaires Disponible Peinture sur métal. Enjeux et nouvelles voies de développement / Association Française des Techniciens des Peintures, Vernis, Encres et Adhésifs / AFTPVA Rhône-Alpes (1998)
Titre : Peinture sur métal. Enjeux et nouvelles voies de développement : Journée technique. Mardi 26 mai 1998, Lyon Type de document : texte imprimé Auteurs : Association Française des Techniciens des Peintures, Vernis, Encres et Adhésifs , Auteur Editeur : AFTPVA Rhône-Alpes Année de publication : 1998 Importance : Pagination multiple Présentation : ill. Format : 30 cm Langues : Français (fre) Catégories : Congrès et conférences
Métaux -- Revêtements:Métaux -- PeintureIndex. décimale : 667.9 Revêtements et enduits Résumé : - Les phosphatations polyvalentes sur support fer, aluminium, zinc.
- Développement des peintures dans le secteur du ferroviaire.
- Utilisation des systèmes de peintures "propres" sur les matériaux roulants ferroviaires.
- Polyester haut extrait sec.
- Les polyuréthanes hot melt.
- Evolution de la peinture de réparation automobile.Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3098 Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 2532 667.9 PEI Colloque, congrès, etc. Bibliothèque principale Documentaires Disponible Les peintures aqueuses à haute performance / Association Française des Techniciens des Peintures, Vernis, Encres et Adhésifs / Paris : AFTPVA (1996)
PermalinkLes peintures pour métaux prélaqués se heurtent aux contraintes extérieures / Baptiste Cessieux in DOUBLE LIAISON, N° 614 (12/2016)
PermalinkPeintures et vernis. Essai de pliage en T - Norme internationale ISO 17132 / International Organization for Standardization (Genève, Suisse) / Geneve [Switzerland] : International Organization for Standardization (ISO) (2007)
PermalinkPeintures et vernis. Spectroscopie d'impédance électrochimique (SIE) sur des éprouvettes revêtues de haute impédance - Partie 4 : Exemples de spectres d'éprouvettes revêtues de polymères - Norme internationale ISO 16773-4 / International Organization for Standardization (Genève, Suisse) / Geneve [Switzerland] : International Organization for Standardization (ISO) (2009)
PermalinkPOSS functionalized with mixed fluoroalkyl and methacryloxy substituents as modifiers for UV-curable coatings / Agnieszka Marcinkowska in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 16, N° 1 (01/2019)
PermalinkPowder coating for ceiling panels in INTERNATIONAL SURFACE TECHNOLOGY (IST), Vol. 8, N° 1 (2015)
PermalinkPowder coatings-service through technology and innovation - Part II / Jagmal Singh in PAINTINDIA, Vol. XLVII, N° 10 (10/1997)
PermalinkPowder coatings - service through technology and innovation - Part II / Jagmal Singh in PAINTINDIA, Vol. XLVII, N° 10 (10/1997)
PermalinkPreventing coating problems and failures on bolted bridge connections / James D. Machen in JOURNAL OF PROTECTIVE COATINGS & LININGS (JPCL), Vol. 33, N° 12 (12/2016)
PermalinkPermalinkReview of crater in cathodic electrodeposition coating and their different cause / Akshay A. Masule in PAINTINDIA, Vol. LXXI, N° 10 (10/2021)
PermalinkSEEP, un procédé alternatif à celui du chrome VI / Voahirana Rakotoson in GALVANO ORGANO, N° 839 (06-07/2015)
PermalinkPermalinkSolventborne paint systems on carbon steel and hot-dip galvanized steel for a wide range of atmospheric exposures / F. Fragata in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 4, N° 1 (03/2007)
PermalinkSynthesis of styrene and n-butyl acrylate latex polymers modified by functional monomers and their waterborne paint applications / Gökhan Akbulut in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 19, N° 5 (09/2022)
Permalink