Accueil
Catégories
Ajouter le résultat dans votre panier Affiner la recherche
Etendre la recherche sur niveau(x) vers le bas
Etude expérimentale et modélisation de l'usure des outils lors du perçage et du détourage de CFRP / Franck Girot in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 23, N° 3 (09-10-11-12/2013)
[article]
fait partie de Vol. 23, N° 3 - 09-10-11-12/2013 - Usinage des matériaux composites : journée scientifique et technique - AMAC (Bulletin de REVUE DES COMPOSITES ET DES MATERIAUX AVANCES) / Rédouane Zitoune
Titre : Etude expérimentale et modélisation de l'usure des outils lors du perçage et du détourage de CFRP Type de document : texte imprimé Auteurs : Franck Girot, Auteur ; Daniel Iliescu, Auteur ; Asier Fernandez Valdivieso, Auteur ; Maria Esther Gutiérrez-Orrantia, Auteur ; Luis Norberto Lopez de Lacalle, Auteur Année de publication : 2013 Article en page(s) : p. 357-385 Note générale : Bibliogr. Langues : Français (fre) Catégories : Carbures
Composites à fibres de carbone
Détourage
Modèles mathématiques
Outillage
Perçage et alésage
Revêtement en diamant
Usinage
Usure (mécanique)Index. décimale : 670.42 Usinage Résumé : Cet article présente une étude expérimentale du perçage et du détourage de CFRP ainsi que des modèles phénoménologiques de prévision et d'évaluation de l'effort d'avance et de l'usure des outils utilisés. Les résultats expérimentaux montrent que la vitesse d'avance, la vitesse de coupe et l'usure de l'outil sont les facteurs significatifs influant sur l'effort axial ou d'avance. En détourage, une géométrie à dents multiples Z14/11 associée à un revêtement épais en AITiN ou en diamant améliore considérablement la durée de vie tout en minimisant la force axiale, la rugosité et le délaminage. Un modèle d'usure a ensuite été développé, sur la base d'un comportement à l'abrasion de l'outil, qui relie l'effort axial ou d'avance aux paramètres géométriques de l'outil et à l'usure. Le modèle a été vérifié par des essais expérimentaux. Note de contenu : - ETUDE EXPERIMENTALE DU DETOURAGE DE CFRP PAR FRAISE A DENTS MULTIPLES (POINTE DE DIAMANT) : Influence de la géométrie - Influence du revêtement - Essais d'endurance sur outils non revêtus
- ETUDE EXPERIMENTALE DU PERCAGE DE CFRP
- MODELE PHENOMENOLOGIQUE : Modèle de détourage - Modèle de perçageDOI : 10.3166/rcma.23.357-385 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=20061
in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 23, N° 3 (09-10-11-12/2013) . - p. 357-385[article]Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 15839 - Périodique Bibliothèque principale Documentaires Disponible A wear simulation study of nanostructured CVD diamond-on-diamond articulation involving concave/convex mating surfaces / Paul A. Baker in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 13, N° 2 (03/2016)
[article]
Titre : A wear simulation study of nanostructured CVD diamond-on-diamond articulation involving concave/convex mating surfaces Type de document : texte imprimé Auteurs : Paul A. Baker, Auteur ; Raymond G. Thompson, Auteur ; Shane A. Catledge, Auteur Année de publication : 2016 Article en page(s) : p. 385-393 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Dépôt chimique en phase vapeur
Métaux -- Revêtements protecteurs
Revêtement en diamant
Simulation, Méthode de
Usure (mécanique)Index. décimale : 667.9 Revêtements et enduits Résumé : Using microwave plasma chemical vapor deposition, a 3-µm-thick nanostructured diamond layer was deposited onto polished, convex, and concave components that were machined from Ti–6Al–4V alloy. These components had the same radius of curvature, 25.4 mm. Wear testing of the surfaces was performed by rotating articulation of the diamond-deposited surfaces (diamond-on-diamond) with a load of 225 N for a total of 5 million cycles in bovine serum resulting in polishing of the diamond surface and formation of very shallow, linear wear grooves of less than 50 nm depth. The two diamond surfaces remained adhered to the components and polished each other to an average surface roughness that was reduced by as much as a factor of 80 for the most polished region located at the center of the condyle. Imaging of the surfaces showed that the initial wearing-in phase of the articulating surfaces by the end of the 5 million cycles. Atomic force microscopy, scanning electron microscopy, Raman spectroscopy, and surface profilometry were used to characterize the surfaces and verify that the diamond remained intact and uniform over the surface, thereby protecting the underlying metal. These wear simulation results show that diamond deposition on Ti alloy has potential application for joint replacement devices with improved longevity over existing devices made of cobalt chrome and ultra-high molecular weight polyethylene. DOI : 10.1007/s11998-015-9738-4 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-015-9738-4.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=26122
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 13, N° 2 (03/2016) . - p. 385-393[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 17962 - Périodique Bibliothèque principale Documentaires Disponible