Accueil
Détail de l'auteur
Auteur Hans-Peter Heim
Commentaire :
Institute for Materials Engineering - Polymer Technology - University of Kassel - Kassel - Germany
|
Documents disponibles écrits par cet auteur
Ajouter le résultat dans votre panier Affiner la recherche
Accurate determination of the injection points / Helmut Ridder in KUNSTSTOFFE PLAST EUROPE, Vol. 93, N° 7/2003 (07/2003)
[article]
Titre : Accurate determination of the injection points Type de document : texte imprimé Auteurs : Helmut Ridder, Auteur ; Hans-Peter Heim, Auteur ; Helmut Potente, Auteur Année de publication : 2003 Article en page(s) : p. 21-25 Langues : Anglais (eng) Index. décimale : 668.4 Plastiques, vinyles Résumé : In the process design of gas-assisted injection moulding process, the positions of the melt and gas injection points have a decisive effect on the subsequent part quality. Part two of this three-part series uses an FE simulation to illustrate the effect of melt distribution on the gas bubble profile, and shows a way to determine the optimum injection location. Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=7164
in KUNSTSTOFFE PLAST EUROPE > Vol. 93, N° 7/2003 (07/2003) . - p. 21-25[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 011076 - Périodique Bibliothèque principale Documentaires Disponible Bio-based alternatives for hard-soft connections / Hans-Peter Heim in KUNSTSTOFFE INTERNATIONAL, Vol. 108, N° 12 (12/2018)
[article]
Titre : Bio-based alternatives for hard-soft connections : Converting cellulose acetate into bicycle accessories and automobile parts by two-component injection molding Type de document : texte imprimé Auteurs : Hans-Peter Heim, Auteur ; Maik Feldmann, Auteur ; Marco Klute, Auteur Année de publication : 2018 Article en page(s) : p. 40-44 Langues : Anglais (eng) Catégories : Acétate de cellulose L'acétate de cellulose est une matière plastique inventée en 1865. C'est l'ester acétate de la cellulose.
Alliages polymères -- propriétés mécaniques
Bioplastiques
Essais de pelage
Matières plastiques -- Moulage par injection multicomposant
Polybutylène succinate
Polylactique, AcideL'acide polylactique (anglais : polylactic acid, abrégé en PLA) est un polymère entièrement biodégradable utilisé dans l'alimentation pour l'emballage des œufs et plus récemment pour remplacer les sacs et cabas en plastiques jusqu'ici distribués dans les commerces. Il est utilisé également en chirurgie où les sutures sont réalisées avec des polymères biodégradables qui sont décomposés par réaction avec l’eau ou sous l’action d’enzymes. Il est également utilisé pour les nouveaux essais de stent biodégradable.
Le PLA peut-être obtenu à partir d'amidon de maïs, ce qui en fait la première alternative naturelle au polyéthylène (le terme de bioplastique est utilisé). En effet, l'acide polylactique est un produit résultant de la fermentation des sucres ou de l'amidon sous l'effet de bactéries synthétisant l'acide lactique. Dans un second temps, l'acide lactique est polymérisé par un nouveau procédé de fermentation, pour devenir de l'acide polylactique.
Ce procédé conduit à des polymères avec des masses molaires relativement basses. Afin de produire un acide polylactique avec des masses molaires plus élevées, l'acide polylactique produit par condensation de l'acide lactique est dépolymérisé, produisant du lactide, qui est à son tour polymérisé par ouverture de cycle.
Le PLA est donc l’un de ces polymères, dans lequel les longues molécules filiformes sont construites par la réaction d’un groupement acide et d’une molécule d’acide lactique sur le groupement hydroxyle d’une autre pour donner une jonction ester. Dans le corps, la réaction se fait en sens inverse et l’acide lactique ainsi libéré est incorporé dans le processus métabolique normal. On obtient un polymère plus résistant en utilisant l'acide glycolique, soit seul, soit combiné à l’acide lactique.
Polyuréthanes
Tension superficielle
Vélo -- MatériauxIndex. décimale : 668.4 Plastiques, vinyles Résumé : Growing customer awareness of ecological issues is reflected in marked increases in sales of bicycle parts and accessories, for example. There are established hard-soft composites for pumps, tools, and other handy products. A research project is now attempting to combine both aspects in bio-based two-component injection molding. Note de contenu : - Ready-to-use bio-based hard-soft composites
- Adhesive properties of the blends compared in peel tests
- Samplings of three different series parts
- Fig. : Bicycle pump handles and mudguards were used for sampling the bio-based two-component compounds
- Fig. 1 : Setup for peel tests according to VDI 2019. The obtained force curves of the adhesion properties can be seen in Figure 2
- Fig. 2 : Comparison of the force curves of the PLA and PLA-FTPU95A blends, each with the soft component TPU95A. The latter showed much higher adhesion values
- Fig. 3 : The stress-strain diagram of various CA+PBS blends shows tensile strength falling as PBS content rises
- Fig. 4 : The Injex Lite bicycle pump handle made from various combinations of materials (lst, 2nd and 4th from above : CA+PBS+TPU75A-FTPU75A (60/20/20); 3rd : CA+PBS+TPU75A (60/20))
- Fig. 5 : Air duct for an automobile engine room produced from various materials combinations on a two-aggregate injection molding machine
- Table 1 : Except of the bio-based plastics used and their properties according to manufacturer's data
- Table 2 : Calculated surface tension of various hard-soft compounds
- Table 3 : Peel forces of the material composites between CA blends and TPU
- Table 4 : Mechanical properties of the CA+PBS blends
- Table 5 : Weight and dimensions of pump handles from various composite materialsEn ligne : https://drive.google.com/file/d/1mGPD3LwebrsKYzAEqu0hbjSEjKJDSucs/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=31429
in KUNSTSTOFFE INTERNATIONAL > Vol. 108, N° 12 (12/2018) . - p. 40-44[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 20464 - Périodique Bibliothèque principale Documentaires Disponible Characterization of anisotropic properties of hot compacted self-reinforced composites (SRCs) via thermal diffusivity measurement / Hans-Peter Heim in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 5 (11/2019)
[article]
Titre : Characterization of anisotropic properties of hot compacted self-reinforced composites (SRCs) via thermal diffusivity measurement Type de document : texte imprimé Auteurs : Hans-Peter Heim, Auteur ; F. Mieth, Auteur ; F. Jakob, Auteur ; M. Schnau, Auteur Année de publication : 2019 Article en page(s) : p. 532–540 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Anisotropie
Caractérisation
Compactage à chaud
Composites thermoplastiques -- Propriétés mécaniques
Composites thermoplastiques -- Propriétés thermiques
Composites thermoplastiques auto-renforcés
Densité
Mesure
Polyéthylène à ultra haut poids moléculaire
Polylactique, AcideL'acide polylactique (anglais : polylactic acid, abrégé en PLA) est un polymère entièrement biodégradable utilisé dans l'alimentation pour l'emballage des œufs et plus récemment pour remplacer les sacs et cabas en plastiques jusqu'ici distribués dans les commerces. Il est utilisé également en chirurgie où les sutures sont réalisées avec des polymères biodégradables qui sont décomposés par réaction avec l’eau ou sous l’action d’enzymes. Il est également utilisé pour les nouveaux essais de stent biodégradable.
Le PLA peut-être obtenu à partir d'amidon de maïs, ce qui en fait la première alternative naturelle au polyéthylène (le terme de bioplastique est utilisé). En effet, l'acide polylactique est un produit résultant de la fermentation des sucres ou de l'amidon sous l'effet de bactéries synthétisant l'acide lactique. Dans un second temps, l'acide lactique est polymérisé par un nouveau procédé de fermentation, pour devenir de l'acide polylactique.
Ce procédé conduit à des polymères avec des masses molaires relativement basses. Afin de produire un acide polylactique avec des masses molaires plus élevées, l'acide polylactique produit par condensation de l'acide lactique est dépolymérisé, produisant du lactide, qui est à son tour polymérisé par ouverture de cycle.
Le PLA est donc l’un de ces polymères, dans lequel les longues molécules filiformes sont construites par la réaction d’un groupement acide et d’une molécule d’acide lactique sur le groupement hydroxyle d’une autre pour donner une jonction ester. Dans le corps, la réaction se fait en sens inverse et l’acide lactique ainsi libéré est incorporé dans le processus métabolique normal. On obtient un polymère plus résistant en utilisant l'acide glycolique, soit seul, soit combiné à l’acide lactique.Index. décimale : 668.4 Plastiques, vinyles Résumé : The mechanical properties of self-reinforced composites (SRCs) produced in a hot compaction process significantly depend on the process parameters. Only a little deviation of the process temperature or pressure causes the component to act differently under mechanical load. This is a chance and a challenge at the same time, since this process is difficult to handle but by properly controlling the process parameters, the mechanical properties can be adjusted, even locally for one component. In this research SRC are manufactured in a hot compaction process. A correlation between process parameters and density is found. Density increased from 0,8 to 0,91 g/cm³ by increasing temperature and pressure in the hot compaction process. The different thermal properties in the direction of orientation (IP) and transverse to orientation (TP) are measured with a laser flash device. It was found that, due to a change in density and molecular orientation, diffusivity and conductivity are influenced in different degrees in IP and TP directions. For interpretation of thermal measurement results, microstructures are analysed with a confocal laser scanning microscope after preparing the specimen with a permanganate etching. A schematic model of conductive path is worked out and discussed. With measurement data the anisotropy of IP and TP diffusivity is calculated, and a model is built to describe relative density related to anisotropy. The highest anisotropy between IP and TP diffusivity was calculated with a ratio of 6 at a relative density of approximately 0,82 g/cm³. Since mechanical properties in correlation to process parameters have already been investigated, results of this investigation, in combination with previous research on mechanical properties, will enable the development of a non-destructive testing method for SRCs by measuring the thermal diffusivity. Note de contenu : - STATE OF TECHNOLOGY
- EXPERIMENTAL STUDIES : Materials - Processing - Preparation - Measuring
- RESULTS : Density - Microscopy - Thermal propertiesDOI : https://doi.org/10.3139/217.3812 En ligne : https://drive.google.com/file/d/1_piOekBofBD3DeQ7_8uKZZgss0mKki6v/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=33615
in INTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 5 (11/2019) . - p. 532–540[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21324 - Périodique Bibliothèque principale Documentaires Disponible Climatic ageing of components of polymer based electrochromic devices / Hans-Peter Heim in INTERNATIONAL POLYMER PROCESSING, Vol. XXVIII, N° 3 (07/2013)
[article]
Titre : Climatic ageing of components of polymer based electrochromic devices Type de document : texte imprimé Auteurs : Hans-Peter Heim, Auteur ; Aline Desjean, Auteur Année de publication : 2013 Article en page(s) : p. 256-260 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Atmosphère humide
Climat
Dispositifs électrochromiques -- Détérioration
Dispositifs électrochromiques -- Effets de la chaleur
Fenêtres en matières plastiques
Polycarbonates
Polymères électrochromesIndex. décimale : 668.4 Plastiques, vinyles Résumé : Combining a shading function and a polycarbonate window displays an attractive alternative to the currently employed glass roof in vehicles. However, the ageing of such a device must be investigated before any application. Therefore, our investigations focus on the ageing of the components of a polycarbonate based electrochromic device. The optical, electrical, mechanical and electrochemical properties of the ion storage layer as well as the substrate will be assessed after storage in a climate with a high humidity and high temperature level. Note de contenu : - Optical properties
- Mechanical properties
- Electrochemical propertiesDOI : 10.3139/217.2657 En ligne : https://drive.google.com/file/d/1fNw8RFFm9Ca_Wd2C9j5MvvWsC-wIVEUY/view?usp=drive [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=19013
in INTERNATIONAL POLYMER PROCESSING > Vol. XXVIII, N° 3 (07/2013) . - p. 256-260[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 15238 - Périodique Bibliothèque principale Documentaires Disponible Comparison of fibre reorientation of short-and long-fibre reinforced polypropylene by injection molding with a rotating mold core / Philipp Land in INTERNATIONAL POLYMER PROCESSING, Vol. 38, N° 1 (2023)
[article]
Titre : Comparison of fibre reorientation of short-and long-fibre reinforced polypropylene by injection molding with a rotating mold core Type de document : texte imprimé Auteurs : Philipp Land, Auteur ; Thorsten Krumpholz, Auteur ; Hans-Peter Heim, Auteur Année de publication : 2023 Article en page(s) : p. 97-110 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Composites à fibres -- Moulage par micro-injection
Composites à fibres courtes
Composites à fibres de verre -- Propriétés mécaniques
Composites à fibres longues
Distribution et orientation des fibres
Moules à noyau rotatif
PolypropylèneIndex. décimale : 668.4 Plastiques, vinyles Résumé : With a rotating mold core during the injection molding of fibre-reinforced plastics, the rotational shear caused by the rotation is superimposed on the injection-induced shear. This allows the fibre orientation in this area to be intentionally manipulated so that, for example, in the case of internal pressure loading, the fibres can be oriented in the tangential main loading direction. This paper deals with the impact of a rotating mold core on the fibre orientation and burst strength of short-and long-fibre-reinforced polypropylene. It is shown that the fibre orientation and strength can be significantly influenced for both short and long fibres, whereby increases in bursting strength of mostly over 80%, in some cases over 200%, could be achieved. The ultimate strength depends, among other things, on the wall thickness used and the fibre content. Major differences between the short-and long-fibre-reinforced polypropylene are less evident in the strength and more in the fibre orientation. Note de contenu : - MATERIALS AND METHODS : Process implementation and manufacturing of test specimens - Materials - Burst pressure test - Fibre orientation analysis
- RESULTS : Short-fibre reinforced PP - Long-fibre reinforced PP - Failure behaviorDOI : https://doi.org/10.1515/ipp-2022-4252 En ligne : https://drive.google.com/file/d/13BYnremJZznNj0YGHJRLOJNM_8ThgSK1/view?usp=share [...] Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39198
in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 1 (2023) . - p. 97-110[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 24052 - Périodique Bibliothèque principale Documentaires Disponible Cross-linked hydrophobic starch granules in blends with PLA / Johannes Fuchs in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIII, N° 1 (03/2018)
PermalinkPermalinkDetermining viscosity directly in the injection molding process / Jan-Christoph Zarges in KUNSTSTOFFE INTERNATIONAL, Vol. 106, N° 10 (10/2016)
PermalinkEffects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding / Marco Klute in INTERNATIONAL POLYMER PROCESSING, Vol. 37, N° 5 (2022)
PermalinkExtrusion in a magnetic field / Hans-Peter Heim in KUNSTSTOFFE PLAST EUROPE, Vol. 95, N° 8/2005 (08/2005)
PermalinkGaim : from the design to successful application / Helmut Potente in KUNSTSTOFFE PLAST EUROPE, Vol. 93, N° 3/2003 (03/2003)
PermalinkPermalinkInfluences on the mechanical properties of SRCs in a combined compacting and back injecting process / Fabian Jakob in INTERNATIONAL POLYMER PROCESSING, Vol. 37, N° 2 (2022)
PermalinkInnovative materials for novel concepts for internal heat exchangers / Annette Rüppel in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIII, N° 4 (08/2018)
PermalinkInvestigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs) / Fabian Jakob in INTERNATIONAL POLYMER PROCESSING, Vol. 37, N° 2 (2022)
PermalinkInvestigations on tightness of polymer-metal hybrids in environments with thermal, media, and mechanical loads / J.-M. Geck in INTERNATIONAL POLYMER PROCESSING, Vol. XXXII, N° 4 (08/2017)
PermalinkJoining of contact pins and conductive compounds via injection molding - Influence of the flow situation on the electrical contact resistance / Hans-Peter Heim in INTERNATIONAL POLYMER PROCESSING, Vol. XXXV, N° 2 (05/2020)
PermalinkLighter thanks to tailored composites / Hans-Peter Heim in KUNSTSTOFFE INTERNATIONAL, Vol. 104, N° 4 (04/2014)
PermalinkMathematical optimization of annular non-return valves / Helmut Potente in KUNSTSTOFFE INTERNATIONAL, Vol. 97, N° 8/2007 (08/2007)
PermalinkMechanical properties of polydimethylsiloxane as a function of the amount and type of crosslinking agent / Fabian Verheyen in INTERNATIONAL POLYMER PROCESSING, Vol. XXXII, N° 3 (07/2017)
Permalink