Accueil
Détail de l'auteur
Auteur Chhiu-Tsu Lin |
Documents disponibles écrits par cet auteur
Ajouter le résultat dans votre panier Affiner la recherche
Chrome - free single - step in - situ phosphatizing coatings on a ti - 6al - 4v titanium alloy / Heather Neuder in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 74, N° 930 (07/2002)
[article]
Titre : Chrome - free single - step in - situ phosphatizing coatings on a ti - 6al - 4v titanium alloy Type de document : texte imprimé Auteurs : Heather Neuder, Auteur ; Chhiu-Tsu Lin, Auteur Année de publication : 2002 Article en page(s) : p. 37-42 Note générale : Bibliogr. Langues : Américain (ame) Index. décimale : 667.9 Revêtements et enduits Résumé : Surface pretreatment, such as chromate conversion, is generally required for the organic coating on Ti-6Al-4V titanium alloys. The surface modification process facilitates bond formation between the titanium surface and adhesives or paints. However, the hexavalent chromate used in the conversion coating is carcinogenic and must be eliminated.
Recently, the “green chemistry” technique of in-situ phosphatizing coatings (ISPC) has been developed at Northern Illinois University. In this study, a polyester-melamine coating system catalyzed by p-toluene sulfonic acid is used as a control paint and applied to bare (paint 1) and chromated (paint 3) Ti alloy panels. The arylphosphonic acid employed as an in-situ phosphatizing reagent (ISPR) is used to formulate ISPC polyester-melamine paint and to react in-situ with the metal surface when ISPC paint is applied on bare Ti panels (paint 2) and chromated Ti panels (paint 4). After soaking in 3% NaCl solution for 1500 hr, the electrochemical impedance, |Z|, was measured as 109, 1010, 1010, and 1010 ohm-cm2 for paints, 1, 2, 3, and 4, respectively. After 1000 hr salt spray (fog) testing, a disbondment from the “X” scribe is observed as 13 and <0.5, <1, <1 mm for paints 1, 2, 3, and 4, respectively. The simultaneous reaction of the ISPR in catalyzing the polymerization of paint film and forming the metal-phosphate layer is the reason for the superior ISPC paint performance.Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5636
in JOURNAL OF COATINGS TECHNOLOGY (JCT) > Vol. 74, N° 930 (07/2002) . - p. 37-42[article]Réservation
Réserver ce documentIn-situ phosphatizing coatings I : an air-dried lacquer system / Chaochua Wang in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 71, N° 892 (05/1999)
[article]
Titre : In-situ phosphatizing coatings I : an air-dried lacquer system Type de document : texte imprimé Auteurs : Chaochua Wang, Auteur ; Yi-Yuan Chuang, Auteur ; Chhiu-Tsu Lin, Auteur Année de publication : 1999 Article en page(s) : p. 61-67 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Bois -- Revêtements protecteurs
Chlorure de sodiumLe chlorure de sodium est un composé chimique de formule NaCl. On l'appelle plus communément sel de table ou de cuisine, ou tout simplement sel dans le langage courant. C'est le principal produit dissous dans l'eau de mer ; on l'appelle alors sel marin.
On l'obtient : dans des marais salants par évaporation de l'eau de mer, dans des mines, par extraction du sel gemme (halite) ou en le synthétisant lors de réactions à hautes températures entre du dichlore (Cl2) et du sodium métallique (Na).
Le chlorure de sodium est utilisé dans l'industrie chimique pour produire du chlore, de la soude caustique et de l’hydrogène.
Laque et laquage
Métaux -- Revêtements protecteurs
Nitrocellulose
Phosphatation
Séchage
Test d'immersion
VernisIndex. décimale : 667.9 Revêtements et enduits Résumé : The formulation of in-situ phosphatizing coatings (ISPCs) was successfully performed for lacquer systems using a commercial nitrocellulose lacquer and an optimum amount of in-situ phosphatizing reagents (ISPRs). The in-situ phosphatizing lacquer (ISPL) system is stable, and shows no change in surface appearance and drying speed as compared to the unmodified lacquer (UML). The ISPLs are applied on pine, poplar, and red oak wood boards, and on cold-rolled steel, aluminum, and laminated brass panels. Immersion tests in a 3% NaCl solution showed a remarkable enhancement in paint disbonding resistance for the paint film of ISPL on wood and metals compared to that of the UML sample. The paint film protective performance of ISPLs is further evidenced by the lattice pattern tape testings, and by the cathodic delamination and electrochemical impedance spectroscopy. Note de contenu : - Disbonding resistance of ISPLs on wood boards
- Disbonding resistance of ISPLs on metal substrates
- Cathodic delamination of ISPLs on metal substrates
- Electrochemical impedance measurements of ISPLs on metal substrates
- Phosphate fundamentals of ISPLs on metal substratesPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=17854
in JOURNAL OF COATINGS TECHNOLOGY (JCT) > Vol. 71, N° 892 (05/1999) . - p. 61-67[article]Réservation
Réserver ce documentIn-situ phosphatizing coatings II : a high-solids polyester baking enamel / Tao Yu in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 71, N° 892 (05/1999)
[article]
Titre : In-situ phosphatizing coatings II : a high-solids polyester baking enamel Type de document : texte imprimé Auteurs : Tao Yu, Auteur ; Chhiu-Tsu Lin, Auteur Année de publication : 1999 Article en page(s) : p. 69-77 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Adhésion
Anticorrosion
Chlorure de sodiumLe chlorure de sodium est un composé chimique de formule NaCl. On l'appelle plus communément sel de table ou de cuisine, ou tout simplement sel dans le langage courant. C'est le principal produit dissous dans l'eau de mer ; on l'appelle alors sel marin.
On l'obtient : dans des marais salants par évaporation de l'eau de mer, dans des mines, par extraction du sel gemme (halite) ou en le synthétisant lors de réactions à hautes températures entre du dichlore (Cl2) et du sodium métallique (Na).
Le chlorure de sodium est utilisé dans l'industrie chimique pour produire du chlore, de la soude caustique et de l’hydrogène.
Couches minces
Essais de brouillard salin
Formulation (Génie chimique)
Haut extrait sec
Immersion
Métaux
Phosphatation
Polyesters
Polymères réticulés
Revêtement émail:Peinture-émail
Stabilité au stockageIndex. décimale : 667.9 Revêtements et enduits Résumé : A single step in-situ phosphatizing coating (ISPC) can be formulated by pre-dispersing an optimal amount of in-situ phosphatizing reagents (ISPRs) into the paint system. The technique of ISPC is applied to a high-solids polyestermalemine baking enamel using a designed ISPR-2. The in-can stability of ISPC is verified using rheological measurements. The coating properties and protective performance of the ISPC are compared to those of the multi-step coating of control sample (MCCS). The immersion tests in a 3% NaCl solution and salt spray testings show a significant improvement in paint disbondment from the X scribe for ISPC. The observed coating performance enhancement of ISPC over MCCS is confirmed from the multi-functionality of ISPRs. Phosphate chemistry proceeds via an acid-base type of interaction, P-O-Mn+, and polymer chemistry generates a covalent P-O-C linkage with the polymer network. Note de contenu : - Crosslinking density verification for the coatings
- ISPC corrosion resistance measurements
- Storage stability of ISPC and its polymer chemistryPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=17855
in JOURNAL OF COATINGS TECHNOLOGY (JCT) > Vol. 71, N° 892 (05/1999) . - p. 69-77[article]Réservation
Réserver ce documentIn-situ phosphatizing coatings III : a water-reducible alkyd baking enamel / Tao Yu in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 71, N° 895 (08/1999)
[article]
Titre : In-situ phosphatizing coatings III : a water-reducible alkyd baking enamel Type de document : texte imprimé Auteurs : Tao Yu, Auteur ; Chhiu-Tsu Lin, Auteur Année de publication : 1999 Article en page(s) : p. 87-95 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Adhésion
Anticorrosifs
Anticorrosion
Formulation (Génie chimique)
Phosphatation
Polyalkydes
Revêtement émail:Peinture-émail
Revêtements en phase aqueuse:Peinture en phase aqueuse
Traîtements de surfaceIndex. décimale : 667.9 Revêtements et enduits Résumé : We report the successful formulation of stable and compatible in-situ phosphatizing coatings (ISPCs) for a waterborne alkyd-amino baking enamel applied on bare cold-rolled steel (CRS), iron phosphated Bonderite 1000 (BD), and iron phosphated plus Parcolene 60 chromated (BD+P60) coupons. The enhanced coating adhesion of water-based ISPCs is confirmed by the cathodic delamination measurements. After 100 hr of salt spray (fog) test, the corrosion resistance performance (measured by the corrosion disbondment across the X scribe, d in mm) of the water-based ISPC on CRS panel (d = 4.0-7.0 mm) outperformed that of the control alkyd paint on B-1000 (d = 26 mm) and also on BD+P60 (d = 14 mm) coupons. The superior coating performance of water-based ISPCs is believed to result from the in-situ metal surface phosphatization as detected by the reflectance FTIR technique. Note de contenu : - Rheology and water-reducible ISPC stability
- Polymer chemistry and paint film quality
- In-situ phosphatization of metal surfaces
- Coating protective performance
- In-situ phosphatization and water disbonding resistance
- Cathodic determination
- ASTM salt spray (fog) testsPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=17925
in JOURNAL OF COATINGS TECHNOLOGY (JCT) > Vol. 71, N° 895 (08/1999) . - p. 87-95[article]Réservation
Réserver ce documentPaints and coatings monitored by laser-induced breakdown spectroscopy / Taesam Kim in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 4, N° 3 (09/2007)
[article]
Titre : Paints and coatings monitored by laser-induced breakdown spectroscopy Type de document : texte imprimé Auteurs : Taesam Kim, Auteur ; Chhiu-Tsu Lin, Auteur ; Vari Minassian, Auteur ; Tinh Nguyen, Auteur Année de publication : 2007 Article en page(s) : p. 241-253 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Acier L'acier est un alliage métallique utilisé dans les domaines de la construction métallique et de la construction mécanique.
L'acier est constitué d'au moins deux éléments, le fer, très majoritaire, et le carbone, dans des proportions comprises entre 0,02 % et 2 % en masse1.
C'est essentiellement la teneur en carbone qui confère à l'alliage les propriétés du métal qu'on appelle "acier". Il existe d’autres métaux à base de fer qui ne sont pas des aciers comme les fontes et les ferronickels par exemple.
Algorithmes
Alliages
AluminiumL'aluminium est un élément chimique, de symbole Al et de numéro atomique 13. C’est un métal pauvre, malléable, de couleur argent, qui est remarquable pour sa résistance à l’oxydation13 et sa faible densité. C'est le métal le plus abondant de l'écorce terrestre et le troisième élément le plus abondant après l'oxygène et le silicium ; il représente en moyenne 8 % de la masse des matériaux de la surface solide de notre planète. L'aluminium est trop réactif pour exister à l'état natif dans le milieu naturel : on le trouve au contraire sous forme combinée dans plus de 270 minéraux différents, son minerai principal étant la bauxite, où il est présent sous forme d’oxyde hydraté dont on extrait l’alumine. Il peut aussi être extrait de la néphéline, de la leucite, de la sillimanite, de l'andalousite et de la muscovite.
L'aluminium métallique est très oxydable, mais est immédiatement passivé par une fine couche d'alumine Al2O3 imperméable de quelques micromètres d'épaisseur qui protège la masse métallique de la corrosion. On parle de protection cinétique, par opposition à une protection thermodynamique, car l’aluminium reste en tout état de cause très sensible à l'oxydation. Cette résistance à la corrosion et sa remarquable légèreté en ont fait un matériau très utilisé industriellement.
L'aluminium est un produit industriel important, sous forme pure ou alliée, notamment dans l'aéronautique, les transports et la construction. Sa nature réactive en fait également un catalyseur et un additif dans l'industrie chimique ; il est ainsi utilisé pour accroître la puissance explosive du nitrate d'ammonium.
Chromates
Galvanisation
Phosphates
Qualité -- Contrôle
Surfaces -- AnalyseIndex. décimale : 667.9 Revêtements et enduits Résumé : Two algorithms-peak picking and peaks correlation-have been compiled in a portable laser-induced breakdown spectroscopy (LIBS) system and used specifically for spectral fingerprinting of paints and coatings, which contain multiple ingredients and require several application steps. The LIBS technique starts with a laser shot on the specimen surface, detection of the emission of the elements present, and analysis of the sample compositions. The LIBS system has been successfully illustrated for the identification and analysis of coating substrates, surface pretreatments, and primer and topcoat paints obtained in the lab and at field sites. The results indicate that, despite the compositional complexity in organic metal finishing, the spectral fingerprint of paints and coatings can be effectively determined by the LIBS technique. The advantages of LIBS technique over other conventional methods, such as EDX, are that it is quasi-nondestructive (<100 µm of sample size), requires no sample preparation, is fast (within minutes), is user-friendly (for nontechnical personnel), and is capable of application both online and at the field sites. Note de contenu : EXPERIMENTAL PROCEDURE : Construction of a laser-induced materials analyzer - Materials of paints and coatings -
RESULTS AND DISCUSSION : LIBS : an in-situ and quasi-nondestructive analytical technique - LIBS characterization of substrates - LIBS characterization of surface pretreatment
layer on substrates - LIBS identification of paints and coating ingredients - Paint failure analysis for the on-site field samples : two casesDOI : 10.1007/s11998-007-9029-9 En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-007-9029-9.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3639
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 4, N° 3 (09/2007) . - p. 241-253[article]Réservation
Réserver ce document