Fils RSS disponibles sur ce site
Matériaux plastiques et composites - Dernières publications | https://e-campus.itech.fr/pmb/opac_css/rss.php?id=9 |
- 700 bar H2 tanks : smaller and lighter [texte imprimé] / Sébastien Panthu, Auteur ; Carolin Cichosz, Auteur . - 2023 . - p. 42-44.Langues : Anglais (eng)in JEC COMPOSITES MAGAZINE > N° 152 (09-10/2023) . - p. 42-44
Catégories : BobinageComposites à fibres de carboneEpoxydesHydrogène -- StockageMatériaux -- AllègementRécipients sous pressionRéservoirs (récipients) Index. décimale : 668.4 Plastiques, vinyles Résumé : Voith and Huntsman Advanced Materials have partnered to meet the industry's demand for safe, lightweight, and high-qulaity hydrogen composite pressure vessels. The collaboration aimed to achieve best cost-performance ratio of the pressure vessels by implementing a new mass production process using towpreg material. Note de contenu : - Higher storage density H2 tanks - Stringent requirements for safe H2 storage - Development of a new towpreg generation - Optimised use of towpreg material for cost effective and fully automated production of H2 Type IV tanks - Plug and drive H2 storage systems meets truck OEM requirements - Fig. 1 Results apply to type IV 700 bar H2 tanks with new towpreg system Voith Composites Carbon4 Tank GEN II-700 bar type IV hydrogen tank with 15.5 kg H2 Capacity, 2,140 mm length and 555 mm in diameter - Fig. 2 : Specific winding pattern - Fig. 3 : Cure simulation pressure vesels - Fig. 4 : Voith's H2 plug and drive system En ligne : https://drive.google.com/file/d/1hR64Og6k1o29cDGcpfUfXQ0XC-0xFw-g/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40572 Biodégradabilité des plastiques biosourcés revue bibliographique sur l'acide polylactique
Biodégradabilité des plastiques biosourcés revue bibliographique sur l'acide polylactique [texte imprimé] . - 2023 . - 15 p.Bibliogr.in MATERIAUX & TECHNIQUES > Vol. 110, N° 6 (12/02/2023) . - 15 p.Catégories : BioplastiquesDigestion anaérobieMatières plastiques -- BiodégradationPolylactique, AcideL'acide polylactique (anglais : polylactic acid, abrégé en PLA) est un polymère entièrement biodégradable utilisé dans l'alimentation pour l'emballage des œufs et plus récemment pour remplacer les sacs et cabas en plastiques jusqu'ici distribués dans les commerces. Il est utilisé également en chirurgie où les sutures sont réalisées avec des polymères biodégradables qui sont décomposés par réaction avec l’eau ou sous l’action d’enzymes. Il est également utilisé pour les nouveaux essais de stent biodégradable. Le PLA peut-être obtenu à partir d'amidon de maïs, ce qui en fait la première alternative naturelle au polyéthylène (le terme de bioplastique est utilisé). En effet, l'acide polylactique est un produit résultant de la fermentation des sucres ou de l'amidon sous l'effet de bactéries synthétisant l'acide lactique. Dans un second temps, l'acide lactique est polymérisé par un nouveau procédé de fermentation, pour devenir de l'acide polylactique. Ce procédé conduit à des polymères avec des masses molaires relativement basses. Afin de produire un acide polylactique avec des masses molaires plus élevées, l'acide polylactique produit par condensation de l'acide lactique est dépolymérisé, produisant du lactide, qui est à son tour polymérisé par ouverture de cycle. Le PLA est donc l’un de ces polymères, dans lequel les longues molécules filiformes sont construites par la réaction d’un groupement acide et d’une molécule d’acide lactique sur le groupement hydroxyle d’une autre pour donner une jonction ester. Dans le corps, la réaction se fait en sens inverse et l’acide lactique ainsi libéré est incorporé dans le processus métabolique normal. On obtient un polymère plus résistant en utilisant l'acide glycolique, soit seul, soit combiné à l’acide lactique. Index. décimale : 668.4 Plastiques, vinyles Résumé : Le développement de plastiques biosourcés est une alternative intéressante pour diminuer la dépendance au pétrole et pour limiter l’effet des plastiques pétrosourcés sur l’environnement conduisant à des effets délétères sur les écosystèmes terrestres et marins. En parallèle du développement de plastiques biosourcés, il est important de se préoccuper de leur fin de vie. Leur dégradation par des processus biologiques en conditions aérobies ou anaérobies permettrait de réduire leur impact environnemental. Parmi les plastiques biosourcés déjà développés depuis plusieurs années, l’acide polylactique (PLA) est l’un des biopolymères les plus produits actuellement. Cet article dresse un état de l’art sur la biodégradation des plastiques à base de PLA en détaillant les principaux mécanismes de biodégradation impliqués en conditions aérobies et anaérobies et les microorganismes catalysant les différentes réactions biochimiques. Il reporte également les différents essais de biodégradation existants standardisés ou non et les techniques analytiques permettant d’évaluer la biodégradabilité du PLA. Note de contenu : - LES BIOPLASTIQUES : Définitions - Evaluation de la biodégradation des bioplastiques - L'ACIDE POLYLACTIQUE : Production de l'acide polylactique - Mécanisme de biodégradation de polymères à basse d'acide polylactique - METHODES ANALYTIQUE PUOR EVALUER LA BIODEGRADATION DE L'ACIDE POLYLACTIQUE : Analyses morphologique par des observations macro ou microscopiques - Mesures de la perte de masse - Respirométrie en conditions aérobies - Respirométrie en conditions anaérobies - Chromatographie d'exclusion stérique - Spectrométrie infrarouge - Calorimétrie différentielle à balayage Référence de l'article : 604 DOI : https://doi.org/10.1051/mattech/2023002 En ligne : https://www.mattech-journal.org/articles/mattech/pdf/2022/06/mt220040.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39385 - Chicken feather protein for the thermal stability and combustion performance of rigid polyurethane foam [texte imprimé] / Xu Zhang, Auteur ; Simiao Sun, Auteur ; Dehe Yuan, Auteur ; Zhi Wang, Auteur ; Hua Xie, Auteur ; Zhanpeng Su, Auteur . - 2023 . - p. 593-635.Bibliogr.Langues : Anglais (eng)in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 5 (2023) . - p. 593-635
Catégories : CombustionÉnergie d'activationL'énergie d'activation est la quantité d'énergie nécessaire pour lancer un processus chimique, le plus souvent une réaction. En effet, pour démarrer un processus, on doit souvent faire face à une barrière énergétique (c’est-à-dire apporter un minimum d'énergie pour le démarrage). Cette quantité est exprimée, selon le système international d'unités, en kJ/mol (kilojoules par mole de réactif).Mousses plastiquesMousses plastiques -- Propriétés thermiquesPlumesPolyuréthanesProtéines animalesStabilité thermique Index. décimale : 668.4 Plastiques, vinyles Résumé : Rigid polyurethane foams (RPUFs) were synthesized with chicken feather protein using the “one-step method” of all-water foaming. Thermogravimetry, pyrolysis kinetics analysis, Cone calorimetry and smoke density (Ds) were used to investigate the effects of chicken feather protein on thermal stability and combustion performance of RPUFs. The results showed that the modified RPUFs with 2.5 wt% chicken feather protein (RPUF-CF1) had the lowest mass loss, the highest integrated program pyrolysis temperature, the highest activation energy, the lowest Ds (13.3), the highest light transmittance (79.3 %), the lowest heat release rate (22.0 kW/m2 and 30.6 kW/m2) and total heat release (2.4 MJ/m2 and 2.8 MJ/m2), which indicated that RPUF-CF1 had better thermal stability and combustion performance. The current research results provide a useful reference for the preparation of RPUFs with good thermal stability by bio-based modification. Note de contenu : - EXPERIMETAL : Materials - Preparation of chicken feather protein - Preparation of flame retardant RPUF - Measurements and characterization - RESULTS AND DISCUSSION : Thermal weight loss analysis - IPDT analysis - Pyrolysis kinetics analysis - Smoke density - Flame retardancy mechanism - Table 1 : Pyrolysis temperature parameters of the RPUFs - Table 2 : Ther thermal weight loss temeprature data of the RPUFs - Table 3 : Pyrolysis kinetic parameters of the RPUFs at different conversion rates with Flynn-Wall-Ozawa method - Table 4 : Pyrolysis kinetic data of the RPUFs with Coats Redfern method at different heating rates - Table 5 : Pyrolysis kinetic parameters of at three heating rated with Kissinger method - Table 6 : Pyrolysis kinetic parameters of RPUFs at different conversion rates witgh the Starink method - Table 7 : Combustion parameters of RPUFs at different radiation intensity DOI : https://doi.org/10.1515/ipp-2023-4364 En ligne : https://drive.google.com/file/d/1N_u4lH9uM6iUCqVv3ypfp9SKuUqJVXck/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40291 - A comparative study on the mechanical properties of African teff and snake grass fiber-reinforced hybrid composites : effect of bio castor seed shell/glass/SiC fillers [texte imprimé] / K. Manickaraj, Auteur ; R. Ramamoorthi, Auteur ; S. Sathish, Auteur ; A. Johnson Santhosh, Auteur . - 2023 . - p. 551-563.Bibliogr.Langues : Anglais (eng)in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 5 (2023) . - p. 551-563
Catégories : Carbure de siliciumCharges (matériaux)Composites à fibres végétalesComposites à fibres végétales -- Propriétés mécaniquesFibres d'herbe à serpentsGraines de ricin et constituantsTeff et constituantsEragrostis tef, le teff ou tef, est une espèce de plantes monocotylédones de la famille des Poaceae (graminées), cultivée comme céréale secondaire en Afrique. Cette plante, originaire des hauts-plateaux d'Érythrée et Éthiopie, où elle est l'ingrédient de base de l’injera (sorte de crêpe) ou de la bière t'ella, a des graines de très petite taille ; on dit qu'une poignée suffit pour ensemencer un champ entier. Ces graines dépourvues de gluten sont précieuses pour les personnes tenues de suivre un régime sans gluten. (Wikipedia)Verre Index. décimale : 668.4 Plastiques, vinyles Résumé : The environmental awareness and sustainable nature of plant-based fibers have forced material researchers and automakers to use natural fibers instead of petroleum-based fibers for various industrial applications. The need for environmentally and biodegradable fibers has created a demand in the transportation industry. In this study, bio castor seed shell (C), glass fiber (G), and SiC (SC) fillers in a constant weight fraction (10 %) were reinforced separately with varying weight fractions (5–25 %) of African teff and snake grass fibers to improve the mechanical properties of the hybrid composites. Both African teff and snake grass fibers were subjected to alkaline treatment to remove amorphous elements such as hemicellulose, lignin, and wax, resulting in high surface roughness. The hybrid composites were fabricated by the compression molding technique and their mechanical properties were characterized as per ASTM standards. The fractured surface of the treated fiber was examined by scanning electron microscopy. From the results, it was found that SC10SG20AT showed maximum mechanical properties compared to C10SG20AT and G10SG20AT due to higher load-bearing capacity of SiC filler. Therefore, SC10SG20AT can be recommended for lightweight applications. Note de contenu : - Materials and methods : Materials - Development of composites - Mechanical, FTIR, and SEM analyses - Results and discussion : Tensile strength - Flexural strength - Impact strength - Interlaminar shear strength - Hardness - FTIR analysis - SEM - Table 1 : The designation of the developed composites DOI : https://doi.org/10.1515/ipp-2023-4343 En ligne : https://drive.google.com/file/d/1z-jmmXsdjZlTxmeyi8yxxpA_QKimbUQY/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40288 Custom-built advanced winding technology machines bring new possibilities
Custom-built advanced winding technology machines bring new possibilities [texte imprimé] / Humphrey Carter, Auteur . - 2023 . - p. 21-23.Langues : Anglais (eng)in JEC COMPOSITES MAGAZINE > N° 152 (09-10/2023) . - p. 21-23Catégories : AutomatisationBobinageComposites à fibres de carboneComposites à fibres de carbone -- Appareils et matérielsEnroulement filamentaireProcédés de fabrication Index. décimale : 668.4 Plastiques, vinyles Résumé : Czech Republic-based CompoTech PLUS spol. s r.o is a composite component design and manufacturing company. It uses proprietary advanced filament laying and axial fibre winding process technologies. They develop and custom manfuacture alternative, lightweight, carbon composites solutiosn to steel and aluminuim. They provide significant design, performance, productivity and cost-saving benefits. Note de contenu : - Robot-assisted automated carbon fibre pallet production - New automated machine-building capabilities - Built-in performance and production flexibility - Robot technology partnership - Customised control software program - Future projects En ligne : https://drive.google.com/file/d/1DvD2AYPB7Ii_dIRXOz14mmbeSBqoBEC6/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40569 Cycle de vie et économie circulaire des plastiques
Cycle de vie et économie circulaire des plastiques [texte imprimé] / Charles Bouchard, Auteur ; Carole Charbuillet, Auteur . - 2020 . - p. 59-60.Langues : Français (fre)in PLASTILIEN > N° 168 (06/2020) . - p. 59-60Catégories : Durée de vie (Ingénierie)Économie circulaireL'économie circulaire est une expression générique désignant un concept économique qui s'inscrit dans le cadre du développement durable et s'inspirant notamment des notions d'économie verte, d’économie de l'usage ou de l'économie de la fonctionnalité, de l'économie de la performance et de l'écologie industrielle (laquelle veut que le déchet d'une industrie soit recyclé en matière première d'une autre industrie ou de la même). Son objectif est de produire des biens et services tout en limitant fortement la consommation et le gaspillage des matières premières, et des sources d'énergies non renouvelables ; Selon la fondation Ellen Mac Arthur (créée pour promouvoir l'économie circulaire1), il s'agit d'une économie industrielle qui est, à dessein ou par intention, réparatrice et dans laquelle les flux de matières sont de deux types bien séparés ; les nutriments biologiques, destinés à ré-entrer dans la biosphère en toute sécurité, et des intrants techniques ("technical nutrients"), conçus pour être recyclés en restant à haut niveau de qualité, sans entrer dans la biosphèreMatières plastiques -- Aspect de l'environnementMatières plastiques -- Industrie -- Aspect de l'environnement Index. décimale : 668.4 Plastiques, vinyles Résumé : Comment concilier les innombrables bénéfices des matières plastiques dans notre quotidien et notre responsabilité environnementale ? L'institut Arts et Métiers de Chambéry intègre dès la conception les impacts environnementaux des produits contenant des plastiques aux côtés de leur performance d'usage grâce à l'ingénierie du cycle de vie. Note de contenu : - La chaire mines urbaines - Figure : Préconisations pour la conception Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=34318 - Free vibration behaviour and some mechanical properties of micro particle reinforced epoxy composites [texte imprimé] / Meltem Ürer, Auteur ; Aydin Demir, Auteur . - 2023 . - p. 606-614.Bibliogr.Langues : Anglais (eng)in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 5 (2023) . - p. 606-614
Catégories : Carbure de boreCarbure de siliciumComposites -- Propriétés mécaniquesEpoxydesEssais dynamiquesGraphiteParticules (matières)Traction (mécanique)Vibrations (mécanique) Index. décimale : 668.4 Plastiques, vinyles Résumé : The epoxy composite specimens of certain sizes were produced by adding graphite, silicon carbide and boron carbide microparticles separately at the rates of 5, 10 and 15 wt% to the epoxy resin. Free vibrations of these composite samples were investigated experimentally in a simple supported vibration test setup. Frequency spectrums were obtained by modal analysis method in this experimental setup. The damping ratios were calculated using the half power bandwidth method. The mechanical properties of these composite specimens were also determined by applying the tensile test. By controlling the obtained vibration values theoretically, the effects of microparticle contributions to these specimens at certain rates on natural frequency and damping properties were investigated in detail. The maximum reduction in natural frequency was observed at 5 wt% of each reinforcement. Only the first natural frequency of the 15 wt% boron carbide reinforced epoxy composite was slightly increased. The damping ratio was increased at 10 wt% graphite added and 5 wt% boron carbide added epoxy composites compared to pure epoxy, but decreased in other composite specimens. Note de contenu : - MATERIALS AND METHODS : Vibration test - Tensile tests and mechanical properties - RESULTS AND DISCUSSIONS : Results on vibration properties - Results on mechanical properties - Table 1 : The first natural frequencies and damping ratios of the composite specimens - Table 2 : Some mechanical properties of the composite specimens DOI : https://doi.org/10.1515/ipp-2023-4379 En ligne : https://drive.google.com/file/d/144QslmJ6INymrGJ1ncldOlkVcco5uUme/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40292 Incorporation de matières plastiques recyclées : comment obtenir la certification
Incorporation de matières plastiques recyclées : comment obtenir la certification [texte imprimé] / Laetitia Goldszmidt, Auteur . - 2023 . - p. 56-59.Langues : Français (fre)in PLASTIQUES & CAOUTCHOUCS MAGAZINE > N° 988 (03-04/2023) . - p. 56-59Catégories : CertificationÉconomie circulaireL'économie circulaire est une expression générique désignant un concept économique qui s'inscrit dans le cadre du développement durable et s'inspirant notamment des notions d'économie verte, d’économie de l'usage ou de l'économie de la fonctionnalité, de l'économie de la performance et de l'écologie industrielle (laquelle veut que le déchet d'une industrie soit recyclé en matière première d'une autre industrie ou de la même). Son objectif est de produire des biens et services tout en limitant fortement la consommation et le gaspillage des matières premières, et des sources d'énergies non renouvelables ; Selon la fondation Ellen Mac Arthur (créée pour promouvoir l'économie circulaire1), il s'agit d'une économie industrielle qui est, à dessein ou par intention, réparatrice et dans laquelle les flux de matières sont de deux types bien séparés ; les nutriments biologiques, destinés à ré-entrer dans la biosphère en toute sécurité, et des intrants techniques ("technical nutrients"), conçus pour être recyclés en restant à haut niveau de qualité, sans entrer dans la biosphèreMatières plastiques -- RecyclageMélangeProduits et matériaux recyclés Index. décimale : 668.4 Plastiques, vinyles Résumé : Economie circulaire : Cinq plasturgiste ont déjà obtenu la nouvelle Certification Incorporation de matières plastiques recyclées développée par le LNE en partenariat avec le Centre technique IPC. Comment les rejoindre ? Mode d'emploi. Note de contenu : - Deux parties aux objectifs distincts - Les principales étapes - Focus sur la partie 1 - Focus sur la partie 2 - Quel lien avec le label More ? - Informations contenues dans les certificats - Encadré 1 : les normes et texte de référence - Encadré 2 : Petit lexique pour appréhender le référentiel En ligne : https://drive.google.com/file/d/1zOAYjiT2mjMQYCTQUX6LlYQsdu9g_6a9/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39225 Integrated lightweight rail vehicle composites structures meet high fire requirements
Integrated lightweight rail vehicle composites structures meet high fire requirements [texte imprimé] . - 2023 . - p. 45-47.Langues : Anglais (eng)in JEC COMPOSITES MAGAZINE > N° 152 (09-10/2023) . - p. 45-47Catégories : Composites à fibres de carboneIncendies -- PréventionIndustrie ferroviaire -- MatériauxMatériaux -- AllègementMatières plastiques dans les trains Index. décimale : 668.4 Plastiques, vinyles Résumé : Four specialised companies, investigated different competitive materials and processes to develop a lightweight car body structure meeting the EN-45545 European railway standard for fire safety. Note de contenu : - Lightening strategy - Manufacturing process : fine-tuning through a scale demonstrator - Manfuacturijng process : scale-up and real testing validation - In summary, advantages offered by this technology - Fig. 1 : Talgo's 3D CAD of a metal train body structure and Tecnalia's 3D CAD of a simplified one-shot composite structure - Fig. 2 : Meshing and FEM analysis - Fig. 3 : Tecnalia's fire-smoke-toxicity tests - Fig. 4 : Conceptual integration structure and bottom face of the scaled demonstrator of the floor coupler area - Fig. 5 : Assembly and inner view of the CFRP car body - Fig. 6 : Full-scale demonstrator of a complete section - Fig. 7 : Demonstrator exhibited at the JEC World Mobility Planet 2023 En ligne : https://drive.google.com/file/d/1xZByBLMu40ZPdv3KR0N1B_qsXEpz_y0u/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40573 - Interactions between marine microorganisms and metal : the start point of a new bioinspired solution for corrosion protection [texte imprimé] / Maria Joao Marques, Auteur ; Julien Jaume, Auteur ; Anthony Diderot, Auteur ; Marie-Line Délia, Auteur ; Régine Basséguy, Auteur . - 2023 . - 9 p.Bibliogr.in MATERIAUX & TECHNIQUES > Vol. 110, N° 6 (12/02/2023) . - 9 p.
Catégories : Algues marinesAluminium -- AlliagesAnimaux marinsAnticorrosionBiodégradationMatériaux bio-inspirésMétaux -- Revêtements protecteursMicroorganismes Index. décimale : 620.112 Résistance et autres propriétés des matériaux, essais non destructifs Résumé : Among the strategies currently used to protect metallic materials from corrosion, and thus increase their durability, conversion treatments and coatings can be considered as the most efficient and cost-effective alternatives. However, these techniques must comply with increasingly stringent regulations such as REACH. On another note, in the field of interactions between microorganisms and conductive material, it has been shown that microorganisms can not only accelerate corrosion in some cases (biocorrosion or MIC) but also inhibit it in others, thus protecting the underlying material (MIC Inhibition). In this context, the MICOATEC ANR project is based on the observation that interactions between an aluminium alloy (AA5083) and microorganisms in the marine environment lead to the formation of a protective layer against corrosion. The MICOATEC project aims to develop, via a biomimetic strategy, a new type of process for producing anti-corrosion coatings. The main goal is therefore to translate the natural biotic process into an abiotic technological process for corrosion protection, without replicating the biofilm itself or incorporating active biocompounds into the coating matrix. Note de contenu : - MATERIALS AND METHODS : Materials and preparation - In situ marine exposure - Characterization after immersion - RESULTS AND DISCUSSION : Digital microscopy - Scanning Electron Microscopy (SEM) with energy dispersive X-ray analysis (EDX) Référence de l'article : 603 DOI : https://doi.org/10.1051/mattech/2023001 En ligne : https://www.mattech-journal.org/articles/mattech/pdf/2022/06/mt220020.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39384 - Mechanical and tribological properties of snake grass fibers reinforced epoxy composites : effect of Java plum seed filler weight fraction [texte imprimé] / Natarajan Ponnusamy, Auteur ; Ponnusamy Rajasekaran, Auteur ; Manoharan Mohanraj, Auteur ; Shanmugam Devi, Auteur . - 2023 . - p. 582-592.Bibliogr.Langues : Anglais (eng)in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 5 (2023) . - p. 582-592
Catégories : Charges (matériaux)Composites à fibres végétales -- Propriétés mécaniquesEpoxydesFibres d'herbe à serpentsFibres végétales -- Propriétés mécaniquesFibres végétales -- Propriétés physiquesGraines de prunier de Java et constituantsRéticulantsTribologie (technologie) Index. décimale : 668.4 Plastiques, vinyles Résumé : Natural fiber composite materials are able to compete with common synthetic materials in situations where the strength-to-weight ratio is important. In this study, we aim to analyze the mechanical, tribological, and surface morphology of composites fabricated from randomly oriented snake grass natural fiber with java plum seed filler. Different weight ratios of fiber to seed filler are chosen: 30:0, 28:2, 26:4, 24:6, 22:8, and 20:10. A 70 % epoxy resin was kept constant in all compositions. The fabricated hybrid composite samples were subjected to tensile, flexural, shear, Shore D hardness, water absorption, and wear tests as per ASTM standards, and the results were compared with those of snake grass mono fiber composites. The 20:10 composite has the maximum tensile strength, impact resistance, flexural strength, hardness, water absorption, and wear resistance compared to other composites. The fiber/matrix adhesion was explored using a scanning electron microscope (SEM). The 20:10 composite shows predominant mechanical and tribological characteristics, making it easier to utilize in structural and automotive applications. Note de contenu : - MATERIALS AND METHODOLOGY : Materials - Fiber extraction - Alkali treatment - Composite fabrication process - TESTING OF COMPOSITE MATERIALS : Water absorption - Hardness Tensile - Flexural - Impact - Wear - Morphology - RESULTS AND DISCUSSION : Water absorption behavior - Shore D hardness - Tensile properties - Flexural properties - Impact test - Specific wear rate and coefficient of friction - Surface morphology investigation of wear specimens - SEM analysis of flexural fractured specimens - Table 1 : Physical and mechanical properties of snake grass fiber - Table 2 : Properties of LY 556 epoxy resin - Table 3 : Chemical properties of hardner HY951 - Table 4 : Composite sample details DOI : https://doi.org/10.1515/ipp-2023-4376 En ligne : https://drive.google.com/file/d/1QuqGH_32knaz78nLhk3w75H1t36jJOfr/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40290 - Mechanical characterization of randomly oriented short Sansevieria Trifasciata natural fibre composites [texte imprimé] / E. Fantin Irudaya Raj, Auteur ; Appadurai, Auteur ; Lurthu Pushparaj, Auteur ; M. Chithambara Thanu, Auteur . - 2023 . - p. 564-581.Bibliogr.Langues : Anglais (eng)in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 5 (2023) . - p. 564-581
Catégories : Analyse thermiqueComposites à fibres courtesComposites à fibres végétales -- Propriétés mécaniquesEssais de résilienceEssais dynamiquesFlexion (mécanique)Impact (mécanique)Microscopie électronique à balayageSansevieria et constituantsSansevieria est un genre de 70 espèces de plantes succulentes, généralement herbacées. Il appartient à la famille des Liliaceae (ou à celle des Dracaenaceae) selon la classification classique. Selon la classification phylogénétique ce genre fut classé dans la famille des Ruscaceae, mais avec la classification APG III (2009) cette famille est devenue invalide et ce genre est actuellement dans la famille des Asparagaceae. Le genre Sansevieria a été intégré au genre Dracaena suite à des études génétiques. Ces espèces sont originaires des régions tropicales d'Afrique ou parfois d'Asie. - Description : Les feuilles sont de forme triangulaire. Certaines espèces présentent des feuilles de 10 cm de large à la base et 15 cm de long. D'autres font 6 cm de large au plus et peuvent atteindre 2 m de haut et former des buissons. La floraison consiste en panicules dressées avec des petites fleurs blanches ou blanc-verdâtre très fragrante à la tombée du jour. Le fruit est une baie rouge ou orange. Certaines espèces de Sansevieria sont considérées comme plantes dépolluantes. Elles absorbent notamment le benzène, le formaldéhyde, le toluène, le trichloréthylène ou encore le xylène. (Wikipedia)StatistiqueTraction (mécanique) Index. décimale : 668.4 Plastiques, vinyles Résumé : The present work investigates the mechanical characteristics of randomly oriented short Sansevieria Trifasciata Fibre Polyester (STFP) composites. The STFP composites are fabricated using compression moulding methods with varying fibre weight percentages (5 %–50 %) and fibre lengths (5 mm–50 mm). It has been observed that the impact, flexural, and tensile strength of STFPs improve as the length of the fibre increases, up to a maximum of 40 mm. After that, these properties start to decrease as the length of the fibre further increases. Further, the analysis revealed that STFPs exhibited an increase in properties when the fibre weight percentage was less than 40 %, followed by a decrease in properties as the fibre percentage increased beyond that point. The impact strength of STFP is around 8.2 J/cm2. Similarly, the STFP has a flexural modulus and strength of about 3.4 GPa and 82.6 MPa, respectively. Lastly, the tensile strength of STFP is around 78.26 MPa, the elongation at break is between 6.25 % and 9.36 %, and the Young’s modulus is 11.8 GPa. The matrix and fibre interaction were examined by Scanning Electron Microscopy (SEM). Furthermore, Thermogravimetric (TGA) and Differential Scanning Calorimeter (DSC) analyses are carried out. From these analyses, the thermal stability of STFP is 200 °C and its activation energy is 65.48 kJ/mol. After a thorough comparison with other well-known natural fibres, the proposed properties of STFP demonstrate its superiority as a practical and effective natural fibre composite. Note de contenu : - MATERIALS AND EXPERIMENTATION : Material collection, preparation, and fabrication - Testing and analysis - RESULTS AND DISCUSSION : Density, porosity, and fibre wt% relationship - Mechanical properties of STF - Scanning Electron Microscopy (SEM) analysis - Thermal analysis - Comparison of STF with other commonly used natural fibres - STATISTICAL ANALYSIS - Table 1 : Comparison of STF with other commonly used natural fibres in architectural/ornamental applications - Table 2 : Analysis of variance DOI : https://doi.org/10.1515/ipp-2023-4377 En ligne : https://drive.google.com/file/d/1gQ8RDyrr4yyfmkA-i6VIbpxR_qs4OiWv/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40289 Mechanical properties of 3D-printed PETG samples : The effect of varying infill patterns
Mechanical properties of 3D-printed PETG samples : The effect of varying infill patterns [texte imprimé] / Osamah Fattah Taresh, Auteur ; Marwan T. Mezher, Auteur ; Entihaa G. Daway, Auteur . - 2023 . - p. 339-345.Bibliogr.Langues : Anglais (eng)in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 33, N° 5 (10/2023) . - p. 339-345Catégories : Impression tridimensionnelleMatières plastiques -- Propriétés mécaniquesModèle de remplissage (technologie)Modélisation par dépôt en fusionPolyéthylène téréphtalate glycol Index. décimale : 668.4 Plastiques, vinyles Résumé : One of the most cost-effective additive manufacturing (AM)/3D printing techniques for complicated geometry components is fused deposition modeling (FDM). FDM is a method of fabricating parts by depositing successive layers of material in accordance with computer-aided design file. The properties of the finished products manufactured with FDM are sensitive to the process parameters used. Most FDM items still lack adequate mechanical characteristics when compared to those produced using conventional methods. This investigation seeks to address this knowledge gap by fabricating tensile specimens from Polyethylene Terephthalate Glycol (PETG) filament in a variety of geometries, including grids, octets, triangles, and hexagons. To verify this claim, samples studied was printed with varying infill percentages (25, 50, 75, and 100) % to see how this impacted the mechanical characteristics such as tensile strength and fractured strain. Although the best results for tensile stress and hardness were achieved with a 100% infill percentage in all four printing situations, the triangles orientation consistently produced the best results. Note de contenu : - Materials and Methods - Results and Discussions : Tensile strength - Fractured strain - Table 1 : The printing parameters of the different printing patterns DOI : https://doi.org/10.18280/rcma.330508 En ligne : https://www.iieta.org/download/file/fid/113413 Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40530 - Mechanical properties of PMMA-based biocomposites with polyamide and polyvinylpyrrolidone blends for denture applications [texte imprimé] / Wassan S. Hussain, Auteur ; Jawad K. Oleiwi, Auteur ; Qahtan A. Hamad, Auteur . - 2023 . - p. 293-302.Bibliogr.Langues : Anglais (eng)in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 33, N° 5 (10/2023) . - p. 293-302
Catégories : BiomatériauxCompositesPolyamide 6Polyméthacrylate de méthyleLe poly(méthacrylate de méthyle) (souvent abrégé en PMMA, de l'anglais Poly(methyl methacrylate)) est un polymère thermoplastique transparent obtenu par polyaddition dont le monomère est le méthacrylate de méthyle (MMA). Ce polymère est plus connu sous son premier nom commercial de Plexiglas (nom déposé), même si le leader global du PMMA est Altuglas International9 du groupe Arkema, sous le nom commercial Altuglas. Il est également vendu sous les noms commerciaux Lucite, Crystalite, Perspex ou Nudec.PolyvinylpyrrolidonePoudresProthèses dentaires Index. décimale : 668.4 Plastiques, vinyles Résumé : By blending heat-cured polymethylmethacrylate (PMMA) resin with two different types of polymers, which are polyamide (PV) type (6) and polyvinylpyrrolidone (PVP) type (K30), added separately with various weight fractions (0, 2, 4 and 6%) to heat-cured PMMA resin as blend matrix, attempts have been made in this study for developing the PMMA resin properties employed for prosthesis complete denture. Sisal powder and coconut powder, two different types of natural powders, were added separately to the polymer blend matrices with varying weight fractions (2%, 4%, and 6%) to prepare composite specimens. Hand lay-up methods were used for preparing all specimens. This study covered the flexural test using the 3-point bending method, the impact test using the Izod method, and the maximum shear stress test using the 3-point bending method. According to the results, adding polymer blends and reinforcing powders boosts the impact strength, while lowering flexural modulus, flexural strength, and maximum shear stress. The composite specimens made of (PMMA-2% PVP-6% sisal) manifested the best impact strength and value (11.875 KJ/m2). These findings lead to the conclusion that using PMMA-based biocomposites with polyamide and polyvinylpyrrolidone blends improved impact strength for denture applications, which is one of the most important properties of these applications. Note de contenu : - EXPERIMENTAL WORK : Materials used - Salinization treatment - Preparation method of specimens - EXPERIMENTAL : Tests - Flexural test Impact test - Maximum shear strength test - RESULTS : Results of flexural text - Results of the impact strength and fracture toughness - Results of the maximum shear stress DOI : https://doi.org/10.18280/rcma.330503 En ligne : https://www.iieta.org/download/file/fid/113371 Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40528 - Mechanical strength enhancement of natural fibre composites via localized hybridization with stitch reinforcement [texte imprimé] / M. Chithambara Thanu, Auteur ; E. Fantin Irudaya Raj, Auteur ; Appadurai, Auteur ; Lurthu Pushparaj, Auteur . - 2023 . - p. 539-550.Bibliogr.Langues : Anglais (eng)in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 5 (2023) . - p. 539-550
Catégories : Assemblages (technologie)Composites -- Propriétés interfacialesComposites à fibres végétales -- Propriétés mécaniquesEssais dynamiquesRenforts (matériaux)Résistance au cisaillement Index. décimale : 668.4 Plastiques, vinyles Résumé : Stress concentration is an unavoidable phenomenon during the fabrication of composite structures. This research focuses on reducing stress concentration. Circular holes made on the composite structural member induce stress-concentrated regions. These stress-concentrated regions around the circular hole (considered as a weak section) were strengthened by adding synthetic fibre (local hybridization) in the form of fibre stitches (locked loop stitch). Through conducting a single fibre pull-out test, the present study analysed the impact of incorporating synthetic fibres in stitch form and the enhancement of Interfacial Shear Strength (IFSS). The load acting on the broken warp fibres is distributed to the broken weft fibres when the number of concentric stitches increases. The increment of concentric stitches resulted in the increase of IFSS due to localized hybridization. The tensile test results also show a significant improvement with 110 Nmm axial fastening force, from 6.749 MPa (for the natural fibre composite) to 76.91 MPa (for locally hybridized with eight concentric stitches). A simple bolted lap joint with local hybridization around the hole has been evaluated for different clamp-up forces. The best combinations of the clamp-up force and the extent of hybridization have been identified. SEM images illustrate the reduced voids and the reduced fibre pull-out due to the local hybridization around delamination-prone areas. Note de contenu : - Literature survey - Experimental : Preparation of IFSS test specimens - Preparation of stitched lap joint test specimens - Results and discussion : IFSS calculation of the SCF/USPR composite - Tensile test results of stitched-reinforced lap joint specimens - Discussion on fractography - Table 1 : SCF/USPR composite sample’s nomenclature - Table 2 : Nomenclature of fastened lap joint tensile test specimens - Table 3 : Tensile test results of stitch reinforced circular hole fastened lap joints DOI : https://doi.org/10.1515/ipp-2023-4371 En ligne : https://drive.google.com/file/d/1aIwyMj42OCsIUKw0mcZ74kIYSzduvz07/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40287 A new paradigm for hydrogen pressure tanks
A new paradigm for hydrogen pressure tanks [texte imprimé] / Gilles Rocher, Auteur . - 2023 . - p. 39-41.Bibliogr.Langues : Anglais (eng)in JEC COMPOSITES MAGAZINE > N° 152 (09-10/2023) . - p. 39-41Catégories : Composites à fibres de carboneEléments finis, Méthode desEnroulement filamentaireEpoxydesHydrogène -- StockageRécipients sous pressionRéservoirs (récipients)StratifiésStructure biaxiale Index. décimale : 668.4 Plastiques, vinyles Résumé : Decarbonisation of the transport sector is becoming a pressing matter. Filament wound Type IV hydrogen tanks are reaching their limits, struggling to meet recyclability and conformability criteria from vehicle manufacturers. A paradigm shift is neded which New Generation Tank SA (NGT) whishes to support through its solutions. Note de contenu : - The state of Type IV tank manufacturing processes today - NGT works to overcome the limits - Fig. 1 : Fibre micro-structure of a Type IV pressure tank produced through epoxy filament winding with crimp and resin-rich pockets and of a biaxial laminate with even fibre-resin distribution - Fig. 2 : design for a conventional Type IV pressure tank and NGT's pressure tank - Fig. 3 : Finite element analysis of NGT pressure tanks for 2-end geometries - Table 1 : Tank length/diameter ratio and storage efficiency, average for the full product range of an EOM and two Type IV pressure tanks suppliers En ligne : https://drive.google.com/file/d/1DmDGjTMP60hUGaALIWJ4jn2VX-PO44Eq/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40571 Numerical simulation of asymmetric composite patch repair for fatigue damaged aluminum plate
Numerical simulation of asymmetric composite patch repair for fatigue damaged aluminum plate [texte imprimé] / Belaid Salim, Auteur ; Babaghayou Meriam Imane, Auteur ; Maati Ahmed, Auteur . - 2023 . - p. 329-338.Bibliogr.Langues : Anglais (eng)in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 33, N° 5 (10/2023) . - p. 329-338Catégories : Aluminium -- AlliagesBoreColles:AdhésifsCompositesEléments finis, Méthode desEpoxydesGraphiteMatériaux -- FatigueMatériaux -- FissurationPatchs de réparationRupture (mécanique)Simulation par ordinateur Index. décimale : 668.4 Plastiques, vinyles Résumé : Repairing structures damaged by fatigue through the use of composite patch bonding is an efficient and economical process to preserve structures and increase their lifespan. Much work is currently being carried out to improve this technique. In this work, a 3D nonlinear numerical simulation by finite element analysis was carried out to study the behavior of the crack front and determine the evolution of the stress intensity factor and the change of stress with respect to distance from the crack point. for an aluminum alloy plate containing a central crack, repaired asymmetrically with a composite patch. The repair of these plates must be more precise and reinforced around the crack point, therefore the stress are high and the stress integrity factor SIF is more important according to the results of this study. Note de contenu : - LITERATURE REVIEW : Structural repair methods, composite patch bonding - Parameter of the break - METHODOLOGY : Software and simulation steps - Presentation of geometric models - The mesh module - RESULTS AND DISCUSSION : Crack behavior analysis - Effect of the mechanical properties of the adhesive - Boron/Epoxy patch simulation - Simulations Graphite/Epoxy - Patch results Stress variation during crack propagation - Table 1 : Dimensions and material properties of the repaired model - Table 2 : S11 and S-Mises stress along the path in the case of Boron/Epoxy patch - Table 3 : S11 and S-Mises along the path in the case of Graphite/Epoxy En ligne : https://www.iieta.org/download/file/fid/113375 Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40529 - Polyvinylidene fluoride/maghnite nanocomposites : fabrication and study of structural, thermal and mechanical properties [texte imprimé] / Zoulikha Khiati, Auteur ; Lahouari Mrah, Auteur . - 2023 . - p. 615-624.Bibliogr.Langues : Anglais (eng)in INTERNATIONAL POLYMER PROCESSING > Vol. 38, N° 5 (2023) . - p. 615-624
Catégories : Analyse mécanique dynamiqueAnalyse thermiqueCaractérisationMatériaux hybridesMatériaux hybrides -- Propriétés mécaniquesPolyfluorure de vinylidèneViscosité Index. décimale : 668.4 Plastiques, vinyles Résumé : An in-depth study of polyvinylidene fluoride (PVDF) based nanocomposite systems will be the focus of this research. This polymer being hydrophobic and apolar, it will be unlikely to generate strong interactions with clay leaves called organophilic maghnite. The challenge of this study will therefore be to manage the load/polymer interfaces by using montmorillonite with specific surface treatments by adding a surfactant Cetyltrimethylammonium bromide. Therefore, a significant improvement in mechanical and thermal properties was observed. The properties of PVDFNC nanocomposites were evaluated using various physico-chemical techniques (XRD, FTIR, TGA, DSC, TEM, SEM). The results of the structural and thermal measurements carried out on these products reveal that the structural concept of the surfactant influences both the morphological profile, the thermal and mechanical properties of the nanocomposites obtained. Accelerated crystallization is observed in PVDNC nanocomposites as an effective nucleation agent, the crystals formed are predominantly β shaped and have a small number of polar α crystals. Measurements by X-ray diffraction, as well as transmission and scanning electron microscopy indicated that modified maghnite was perfectly distributed 3 % by weight in the polyvinylidene fluoride matrix. The mechanical properties of the nanocomposites were evaluated according to the filler material used and the polyvinylidene fluoride matrix. Note de contenu : - MATERIALS AND METHODS : Materials - Preparation of PVDFN nanocomposites - Characterization - RESULTS AND DISCUSSION : FTIR analysis - X-ray diffraction analysis - Transmission electron microscopy analysis - Scanning electron microscopy analysis - Optical microscopy - Thermogravimetric analysis - DSC - Index of fluidity (IF) - Dynamic mechanical thermal analysis (DMTA) - Mechanical properties - Table 1 : The mechanical properties of the polymer PVDF and its nanocomposites DOI : https://doi.org/10.1515/ipp-2022-4302 En ligne : https://drive.google.com/file/d/1HzmeWpX0XDfyOG9B3TOQk7Aygdcr1R30/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40293 Surmoulage de textiles lumineux pour une intégration en intérieur automobile
Surmoulage de textiles lumineux pour une intégration en intérieur automobile [texte imprimé] / Sophie Mahé, Auteur ; Lionel Tenchine, Auteur ; Christophe Rouvière, Auteur . - 2023 . - p. 60-63.Langues : Français (fre)in PLASTIQUES & CAOUTCHOUCS MAGAZINE > N° 988 (03-04/2023) . - p. 60-63Catégories : Automobiles -- HabitaclesComposites à fibres synthétiquesPolyéthylène téréphtalatePolyméthacrylate de méthyleLe poly(méthacrylate de méthyle) (souvent abrégé en PMMA, de l'anglais Poly(methyl methacrylate)) est un polymère thermoplastique transparent obtenu par polyaddition dont le monomère est le méthacrylate de méthyle (MMA). Ce polymère est plus connu sous son premier nom commercial de Plexiglas (nom déposé), même si le leader global du PMMA est Altuglas International9 du groupe Arkema, sous le nom commercial Altuglas. Il est également vendu sous les noms commerciaux Lucite, Crystalite, Perspex ou Nudec.Textiles et tissus -- Emploi dans l'industrie automobileTextiles et tissus à usages techniquesTextiles et tissus à usages techniques -- Propriétés thermiquesTextiles et tissus lumineuxTextiles et tissus synthétiques Index. décimale : 668.4 Plastiques, vinyles Résumé : Fonctionnalisation - A la fois lieu de confort et de sécurité, l'habitacle automobile évolue avec les transformations du secteur : affichage, connectivité, intelligence, etc. Dans ce contexte, comment les futurs véhicules autonomes peuvent-ils interagir avec le conducteur en toute sécurité ? Note de contenu : - Textiles lumineux : un enjeu pour l'intégration de fonctions - La caractérisation des textiles lumineux - Le surmoulage des tissus à fibres optiques - La validation du démonstrateur automobile - Encadré 1 : Le projet LITEVA - Encadré 2 : Le complex lumineux - Fig. 1 : Evolution de la luminance des complexes en fonction de la température lors des essais de traction en laboratoire - Fig. 2 : Résultats des essais de thermoformage sur le complexe lumineux En ligne : https://drive.google.com/file/d/1rrX4bXKEWuPPgNkooy7QO6A8nsP7KJDv/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39226 A sustainable future for the composites industry
A sustainable future for the composites industry [texte imprimé] / Guillaume Perben, Auteur . - 2023 . - p. 24-27.Langues : Anglais (eng)in JEC COMPOSITES MAGAZINE > N° 152 (09-10/2023) . - p. 24-27Catégories : Bateaux -- MatériauxComposites à fibres de verre -- RecyclageEpoxydesPyrolyseLa pyrolyse est la décomposition ou thermolyse d'un composé organique par la chaleur pour obtenir d'autres produits (gaz et matière) qu'il ne contenait pas. L'opération est réalisée en l'absence d'oxygène ou en atmosphère pauvre en oxygène pour éviter l'oxydation et la combustion (L’opération ne produit donc pas de flamme). Il s'agit du premier stade de transformation thermique après la déshydratation. Elle permet généralement d'obtenir un solide carboné, une huile et un gaz. Elle débute à un niveau de température relativement bas (à partir de 200 °C) et se poursuit jusqu'à 1 000 °C environ. Selon la température, la proportion des trois composés résultants est différente. Index. décimale : 668.4 Plastiques, vinyles Résumé : Versatile, light, cheap, durable, and with seeminglylimitless applications, it is no exaggeration to say that GFRP has revolutionised manufacturing across most major industries since its mass commercialisation roughly 50 years ago. Unfortunately, the same durability that makes GFRP the material of choice for so many products has also made the task of finding end-of-life solutions incredibly challenging. Note de contenu : - What options are available for the composites industry ? - Let's try again - Pyrolysis and post-treatment - A fresh go-to-market approach - APER : a test case in boat recycling - Closing the loop on the composites industry - Fig. 1 : Schematic diagram of a pyrolysis system - Fig. 2 : Glass fibre reinforced epoxy sample before and after pyrolysis ; the GFRP is composed of 10 sheets of woven glass fibres ; after pyrolysis, the fibres are covered with a residual layer of amorphous carbon - Fig. 3 : Electron microscope images show the reslut when the amorphous carbon is removed, leaving the original fibres clean and intact - Fig. 4 : Composites recycling's process map - Fig. 5 : The mobile recycling units will fit into a container like this one, to ensure access to any waste storage location En ligne : https://drive.google.com/file/d/1lcwPoyZcSkhLieOJwvCRIv1SH5TIm4i9/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=40570 Test sur mesure pour évaluer la durabilité des matériaux sous irradiation
Test sur mesure pour évaluer la durabilité des matériaux sous irradiation : Est-il possible d’évaluer la durabilité de matériaux dans des conditions proches des conditions de services lorsque celles-ci incluent un environnement radiatif ? [texte imprimé] / Lucille Brun, Auteur ; Arnaud Chapon, Auteur . - 2023 . - 4 p.Bibliogr.in MATERIAUX & TECHNIQUES > Vol. 110, N° 6 (12/02/2023) . - 4 p.Catégories : Durée de vie (Ingénierie)Essais de résilienceIrradiationRésistance des matériaux Index. décimale : 620.112 Résistance et autres propriétés des matériaux, essais non destructifs Résumé : Nous présentons un dispositif d’essais pour de nouveaux tests destinés à la qualification de matériaux pour les environnements soumis à une irradiation. Ce dispositif comprend un accélérateur de particules, qui permet de caractériser les effets de l’irradiation sur un matériau et/ou son environnement. Ce moyen d’essais pourra être utilisé dans des projets de recherche dans des secteurs d’activité tels que le nucléaire, le médical ou le spatial. Note de contenu : - Irradiation de matières - Equipement d'irradiation - Test de qualification d'une cellule d'essai DOI : https://doi.org/10.1051/mattech/2023006 En ligne : https://www.mattech-journal.org/articles/mattech/pdf/2022/06/mattech230006s.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=39387