Accueil
Résultat de la recherche
23 résultat(s) recherche sur le tag 'Cisaillement'
Ajouter le résultat dans votre panier Affiner la recherche Générer le flux rss de la recherche
Partager le résultat de cette recherche
Comportement en cisaillement de matériaux composites carbone/PPS et carbone/PEEK sous haute température / Chen Qianqian in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 21, N° 1 (01-02-03-04/2011)
[article]
fait partie de Vol. 21, N° 1 - 01-02-03-04/2011 - Comportement mécanique des renforts et des composites tissés (Bulletin de REVUE DES COMPOSITES ET DES MATERIAUX AVANCES) / Zoheir Aboura
Titre : Comportement en cisaillement de matériaux composites carbone/PPS et carbone/PEEK sous haute température Type de document : texte imprimé Auteurs : Chen Qianqian, Auteur ; Philippe Boisse, Auteur ; Tarek Mabrouki, Auteur ; Abdelghani Saouab, Auteur ; Chung-Hae Park, Auteur ; Joël Bréard, Auteur Année de publication : 2011 Article en page(s) : p. 105-117 Note générale : Bibliogr. Langues : Français (fre) Catégories : Cisaillement (mécanique)
Composites à fibres de carbone
Polyéther éther cétone
Polysulfures de phénylène
TissésTags : 'Composites fibres continues matrice thermoplastique' (CFRTP) Cisaillement Bias-test. Index. décimale : 620.192 Polymères, plastiques Résumé : Lors de la mise en forme de matériaux composites à fibres continues et à matrice thermoplastique (CFRTP) notamment par le procédé d’estampage, le cisaillement dans le plan du renfort tissé est l’un des mécanismes de déformation important à caractériser. Dans ce travail, des essais de bias-test à chaud sur des CFRTP (carbone/PPS et carbone/PEEK), sous une série de températures et pour différentes vitesses d’étirement sont réalisés. Ces essais nous ont permis d’analyser l’influence du taux de déformation et celle de la température sur le comportement de cisaillement plan du composite. Note de contenu : - ESSAIS BIAS-TEST A CHAUD : Dispositif et éprouvette - Essais de bias-test à chaud pour carbone/PPS - Essais de bias-test à chaud pour carbone/PEEK DOI : 10.3166/rcma.21.105-117 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=11336
in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 21, N° 1 (01-02-03-04/2011) . - p. 105-117[article]Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 012996 - Périodique Bibliothèque principale Documentaires Disponible A novel approach for the evaluation of ice release performance of coatings using static friction measurements / M. Martinsen in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 18, N° 3 (05/2021)
[article]
Titre : A novel approach for the evaluation of ice release performance of coatings using static friction measurements Type de document : texte imprimé Auteurs : M. Martinsen, Auteur ; K. O. Hed, Auteur ; J. S. Diget, Auteur ; H. L. Lein, Auteur Année de publication : 2021 Article en page(s) : p. 665-676 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Cisaillement (mécanique)
Frottements (mécanique)
Plan d'expérience
Polyacryliques
PolydiméthylsiloxaneLe polydiméthylsiloxane —[O-Si(CH3)2]n—, ou poly(diméthylsiloxane) selon la nomenclature systématique, communément appelé PDMS ou diméthicone, est un polymère organominéral de la famille des siloxanes souvent présent dans les shampoings. On l'y ajoute pour augmenter le volume des cheveux mais il peut également aller boucher les pores du cuir chevelu et rendre les cheveux gras. C'est une des raisons pour lesquelles se laver les cheveux tous les jours est très déconseillé avec un shampooing contenant des silicones.
Il existe également de l'amodiméthicone, qui est un dérivé du diméthicone.
Le polydiméthylsiloxane est un additif alimentaire (E900), utilisé comme antimoussant dans les boissons (Coca-Cola BlāK).
La chaîne de poly(diméthylsiloxane) forme également la structure de base des huiles et des caoutchoucs silicones.
Polymères -- Synthèse
Polyols
Polyuréthanes
Revêtements -- Propriétés mécaniques
Revêtements anti-adhésion
Revêtements antigel
Revêtements organiquesTags : 'Adhérence de la glace' 'Frottement statique' 'Résistance au cisaillement sur Index. décimale : 667.9 Revêtements et enduits Résumé : Atmospheric icing on structures and equipment represents a challenge for operation and safety. Passive ice removal by ice-phobic coatings has received much attention over the last decades. The current state-of-the-art methods for quantifying the ice-release properties of such coatings suffer from a range of drawbacks, including poor reproducibility and high complexity test setups. Here, a facile rotational tribometer approach for measuring the static friction between polymeric coatings and ice is presented. The torque necessary to initiate motion at the coating-ice interphase was used as a measure of ice release. For a polydimethylsiloxane-based coating (Sylgard 184), the effects of ice-temperature, normal force, coating thickness, and dwell time (contact time between coating and ice at rest with fully applied normal force prior to applying torque) were established along with the conditions resulting in least data variation. With these conditions, tribology-based friction measurements were carried out on two additional coatings ; a two-component polyurethane, and a commercial foul release coating. The outcome of the method, i.e., grading of the coatings in terms of antiicing effect, matched those obtained with a widely used ice adhesion test method based on ice shear adhesion testing. The same trends are revealed by the two methods. However, the findings from the proposed tribology-based method result in consistently lower variation in outcomes and offer more detail on the ice adhesion and friction mechanisms. Note de contenu : - EXPERIMENTAL : Materials - Analytical methods - Synthesis of polyacrylic polyol - Coating preparations - Break-away torque and sliding friction measurements - Ice shear test - Experimental design
- RESULTS AND DISCUSSION : Determining the break-away torque - Influence of temperature, normal force, dwell time, and coating thickness on break-away torque - Reproducibility of break-away torque measurements for Sylgard 184 - Sliding friction - Correlation between break-away torque and shear stress
- Table 1 : Mechanical properties and static WCA of the test coatings at 23°C
- Table 2 :Defined factors and design space
- Table 3 : Results from the design of experiments with experimental parameters where break-away torque is given as an average of two measurements carried out on the Sylgard 184 coating systemDOI : https://doi.org/10.1007/s11998-020-00431-3 En ligne : https://link.springer.com/content/pdf/10.1007/s11998-020-00431-3.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=35920
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 18, N° 3 (05/2021) . - p. 665-676[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 22785 - Périodique Bibliothèque principale Documentaires Disponible Operability limits for non-Newtonian liquids in dual-layer slot coating processes using the viscocapillary model / Jin Seok Park in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 19, N° 1 (01/2022)
[article]
Titre : Operability limits for non-Newtonian liquids in dual-layer slot coating processes using the viscocapillary model Type de document : texte imprimé Auteurs : Jin Seok Park, Auteur ; Taehyung Yoo, Auteur ; Kwan-Young Lee, Auteur ; Hyun Wook Jung, Auteur Année de publication : 2022 Article en page(s) : p. pages 35-47 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Cisaillement (mécanique)
Enduction par filière
Enrobage (technologie)
Fluides non newtoniens
Revêtements
RhéologieTags : 'Revêtement de fente à double couche' Cisaillement 'Modèle viscocapillaire' 'Invasion mi-chemin' 'Limites d'opérabilité' Index. décimale : 667.9 Revêtements et enduits Résumé : The operability windows and coating bead dynamics for the dual-layer slot coating process with non-Newtonian coating liquids were investigated using the viscocapillary model, a two-dimensional (2D) CFD simulation, and experiments. The simplified viscocapillary model derived from the 2D equation of motion with the shear-thinning Carreau liquids bounds the uniform coating regime without defects such as leaking, bead break-up, and mid-gap invasion in dual-layer coating systems. The coating bead flows from experiments and finite-volume-based 2D simulations with the volume-of-fluid scheme demonstrate the performance of the viscocapillary model in reliably tracking the upstream meniscus position of the bottom layer in the coating bead region. The onset of leaking, bead break-up, and mid-gap invasion defects is strongly affected by the rheological properties of Carreau-type coating liquids and the flow ratio between the top and bottom layers. In particular, the relative thickness of the shear-thinning bottom layer at the onset of mid-gap invasion is smaller than the well-known 1/3 value in the Newtonian case, depending on the degree of shear thinning. Note de contenu : - Viscocapillary model for non-Newtonian dual-slot coating flow
- Experimental methods
- CFD simulations
- Results and discussion : Comparison of operability limits and coating bead dynamics - Effect of the flow ratio on the operability limits - Effect of rheological properties of coating liquids in the modelDOI : https://doi.org/10.1007/s11998-021-00499-5 En ligne : https://link.springer.com/content/pdf/10.1007/s11998-021-00499-5.pdf Format de la ressource électronique : Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=37143
in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 19, N° 1 (01/2022) . - p. pages 35-47[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 23313 - Périodique Bibliothèque principale Documentaires Disponible Un outil Matlab pour le calcul des caractéristiques mécaniques d'une section composite quelconque / Rached El Fatmi in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 22, N° 3 (09-10-11-12/2012)
[article]
fait partie de Vol. 22, N° 3 - 09-10-11-12/2012 - Comportement et durabilité des matériaux composites (Bulletin de REVUE DES COMPOSITES ET DES MATERIAUX AVANCES) / Damien Halm
Titre : Un outil Matlab pour le calcul des caractéristiques mécaniques d'une section composite quelconque Type de document : texte imprimé Auteurs : Rached El Fatmi, Auteur Année de publication : 2012 Article en page(s) : p. 395-413 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Cisaillement (mécanique)
Composites
Contraintes (mécanique)
Gauchissement (matériaux)
PoutresTags : Poutre 'Saint Venant' Composite 'Constantes section' 'Effet Poisson' Gauchissement Cisaillement Index. décimale : 668.4 Plastiques, vinyles Résumé : On présente un programme Matlas, CSection, dédié au calcul systématique, par éléments finis, des caractéristiques mécaniques d'une section (CMS) composite quelconque. Ces CMS, qui sont extraites de la solution 3D de Saint Venant, sont l'opérateur de comportement 1D de la poutre, les champs de contrainte de section et les champs de déplacement qui décrivent la déformation de la section. Ces CMS, qui constituent autant d'informations sur le comportement mécanique de la section, offrent à l'ingénieur R&D une réelle aide pour concevoir et optimiser une section ou calculer une poutre composite. Pour illustrer les performances de CSection deux exemples significatifs sont présentés : une section homogène et une section stratifiée constituées de 8 couches orthotropes. Note de contenu : - 3D/1D SAINT VENANT'S THEORY AND SECTIONAL CHARACTERISTICS : Saint Venant's problem extended to composite beam - 3D Saint Venant's solution and sectional characteristics - Saint-Venant (1D) beam-like theory
- QUICK DESCRIPTION OF MATLAB VERSION OF CSECTION
- TWO ILLUSTRATIVE EXAMPLES : Homogeneous rectangular section - Laminated section - Comments - Computation of composite section and composite beam - Higher order beam theories development
- ANNEX A. THE NUMERICAL METHOD : Mathematical characterization of the sectional characteristics - Computation techniqueDOI : 10.3166/rcma.22.395-413 Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=16695
in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES > Vol. 22, N° 3 (09-10-11-12/2012) . - p. 395-413[article]Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 14379 - Périodique Bibliothèque principale Documentaires Disponible Lois de comportement non locales et les transformations de phase sous cisaillement des solutions de surfactants / Ovidiu Radulescu in LES CAHIERS DE RHEOLOGIE, Vol. XVII, N° 1 (10/2000)
[article]
Titre : Lois de comportement non locales et les transformations de phase sous cisaillement des solutions de surfactants Type de document : texte imprimé Auteurs : Ovidiu Radulescu, Auteur ; Peter D. Olmsted, Auteur Année de publication : 2000 Article en page(s) : p. 191-199 Note générale : Bibliogr. Langues : Français (fre) Catégories : Polymères
Rhéologie
SurfactantsTags : Surfactant 'Lois de comportement' 'Instabilités constitutives' 'Polymères en solution' cisaillement Index. décimale : 532.05 Mécanique des fluides et des liquides - Dynamique (cinétique et cinématique) Résumé : Les polymères "vivants" obtenus dans les solutions de surfactants passent sous cisaillement d'une phase isotrope à une phase nématique. Cette transformation conduit à des aspects intéressants de la rhéologie de ces solutions. Les courbes d'écoulement sont non analytiques et présentent un palier. Sur le palier, l'écoulement est en bandes et les transients associés à la formation des bandes sont très complexes. La plupart de ces propriétés peuvent être expliquées à l'aide des extensions non locales des lois de comportement. Des telles extensions sont nécessaires pour rendre compte de la diffusion du paramètre d'ordre de la transformation dans la région fortement non homogène de l'interface entre les bandes. Une estimation expérimentale du coefficient de diffusion est obtenu en étudiant le déplacement de l'interface lorsque le taux de cisaillement change sur le palier. Note de contenu : - MODÈLES NON LOCAUX
- DÉPLACEMENT DE L'INTERFACE : Calcul de la valeur sélectionnée de la contrainte - Estimation expérimentale de D
- PIC ET OSCILLATIONS DE LA CONTRAINTEPermalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=25821
in LES CAHIERS DE RHEOLOGIE > Vol. XVII, N° 1 (10/2000) . - p. 191-199[article]Réservation
Réserver ce document
Exemplaires (1)
Code-barres Cote Support Localisation Section Disponibilité 21931 - Périodique Bibliothèque principale Documentaires Disponible Creeping sphere-plane squeeze flow to determine the zero-shear-rate viscosity of HDPE melts / Edwin C. Cua in APPLIED RHEOLOGY, Vol. 14, N° 1 (2004)
PermalinkExamen du modèle d'ampoule de E. Yoffe / Manuel Buisson in MATERIAUX & TECHNIQUES, Vol. 103, N° 6 (2015)
PermalinkRhéométrie des géosuspensions : de la pâte de ciment au micro-béton / Z. Toutou in RHEOLOGIE, Vol. 4 (11/2003)
PermalinkPermalinkLaser-assisted thermoplastic tape laying / Christian Brecher in JEC COMPOSITES MAGAZINE, N° 56 (04/2010)
PermalinkMechanical properties vs. fabrication for medical applications / R. R. Habeb in JEC COMPOSITES MAGAZINE, N° 63 (03/2011)
PermalinkMultiscale hybrid carbon reinforcement for polymeric-matrix composites / R. Giorgi in JEC COMPOSITES MAGAZINE, N° 62 (01-02/2011)
PermalinkApplication of collagen colloid from chrome shavings for innovative polycondensation adhesives / Ján Sedliacik in JOURNAL OF THE AMERICAN LEATHER CHEMISTS ASSOCIATION (JALCA), Vol. CVI, N° 11 (11/2011)
PermalinkEtude de la puissance d'agitation en cuve aérée ou non aérée d'un fluide viscoélastique / A. Tolofoudyé in LES CAHIERS DE RHEOLOGIE, Vol. XV, N° 4 (10/1997)
PermalinkModified single finite Fourier cosine integral transform method for finding the critical elastic buckling loads of first order shear deformable beams with fixed ends / Charles C. Ike in REVUE DES COMPOSITES ET DES MATERIAUX AVANCES, Vol. 29, N° 6 (12/2019)
PermalinkA new rheometer for the extensional properties of viscoelastic liquids / D. Della Valle in LES CAHIERS DE RHEOLOGIE, Vol. XV, N° 4 (10/1997)
PermalinkRhéologie de la phase d'oignons / P. Panizza in LES CAHIERS DE RHEOLOGIE, Vol. XIV, N° 2 (09/1995)
PermalinkRheology and structure of complex fluids via nonequilibrium molecular dynamics / Siegfried Hess in LES CAHIERS DE RHEOLOGIE, Vol. XV, N° 1 (10/1996)
PermalinkStabilization of aluminum pigment in waterborne paints / Bodo Müller in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 73, N° 917 (06/2001)
PermalinkStructure/property relationships in flexible alkoxysilane automotive coatings / Phillip V. Yaneff in JOURNAL OF COATINGS TECHNOLOGY (JCT), Vol. 74, N° 933 (10/2002)
PermalinkTailoring HASE rheology through polymer design : Effects of hydrophobe size, acid content, and molecular weight / Wenjun Wu in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 2, N° 6 (04/2005)
PermalinkWaterborne latex coatings of color : I. Component influences on viscosity decreases / David M. Mahli in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 2, N° 8 (10/2005)
PermalinkWaterborne latex coatings of color : II. Surfactant influences on color development and viscosity / David M. Mahli in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 2, N° 8 (10/2005)
Permalink