Crosslinked polyurethane–epoxy hybrid emulsion with core–shell structure / Wen Xiufang in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 7, N° 3 (05/2010)  

[article]  inJOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 7, N° 3 (05/2010) . - p. 373-381 Titre : Crosslinked polyurethane–epoxy hybrid emulsion with core–shell structure Type de document : texte imprimé Auteurs : Wen Xiufang, Auteur ; Ruilian Mi, Auteur ; Huang Ying, Auteur ; Jiang Cheng, Auteur ; Pi Pihui, Auteur ; Zuohru Yang, Auteur Année de publication : 2010 Article en page(s) : p. 373-381 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Epoxydes Polyuréthanes Réticulation (polymérisation) Revêtements en phase aqueuse:Peinture en phase aqueuse Index. décimale : 667.9 Revêtements et enduits Résumé : An epoxy resin was used to prepare crosslinked polyurethane hybrid emulsion through the blocked NCO prepolymer mixing process. Due to their hydrophobicity, the amine chain extender, blocked –NCO, and epoxy are located inside the emulsion particles. Thus, the crosslinking reaction occurs mostly in the interior of the particles. In this way, the crosslinking density of the resin is increased without the use of solidifying agents or heating during film formation, and the stability of the emulsions remains uninfluenced. The effects of the type of amine chain extender and the type, dosage, and addition mode of the epoxy resin were studied in terms of mechanical properties and swelling properties in water and toluene of the cast films. Additionally, the stability of the single-pack hybrid emulsion was studied. The results showed that the sample prepared with diethylene triamine had good stability, chemical resistance, and high mechanical strength. The modulus and water resistance of the films increased with the epoxy resin content, which could reach 20 wt %. The type of amine chain extender affected the stability of the emulsions significantly. The molar ratio of NH/NCO at 1:1 led to the best film performance. The optimal temperature of the chain-extension reaction was approximately 80°C. The hybrid emulsions could be stored for at least 6 months without apparent performance changes. DOI : 10.1007/s11998-009-9196-y En ligne : https://link.springer.com/content/pdf/10.1007%2Fs11998-009-9196-y.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=9816 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
012381	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Flooding and floating in latex paint / Huang Ying in JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH, Vol. 1, N° 3 (07/2004)  

[article]  inJOURNAL OF COATINGS TECHNOLOGY AND RESEARCH > Vol. 1, N° 3 (07/2004) . - p. 213-218 Titre : Flooding and floating in latex paint Type de document : texte imprimé Auteurs : Huang Ying, Auteur ; Jiang Cheng, Auteur ; Wen Xiufang, Auteur ; Yang Zhuoru, Auteur Année de publication : 2004 Article en page(s) : p. 213-218 Note générale : Bibliogr. Langues : Américain (ame) Catégories : Applications extérieures Latex Revêtement mural:Peinture murale Revêtements -- Défauts:Peinture -- Défauts Index. décimale : 667.9 Revêtements et enduits Résumé : Flooding and floating are problems in many paint applications. If pigment concentration is uniform on the surface but not through the thickness of the film, one refers to 'flooding' (horizontal separation). If, however, concentration differences are visible across the surface of the paint film, one refers to 'floating' (vertical separation). In this article, the influence of pigment, filler, additives, and processing conditions on the flooding and floating of colored latex paint were investigated. It was discovered that too broad a distribution of pigment and filler particle size can lead to flooding and floating. Different levels of pigment (TiO2) or filler (kaolin) loading cause diverse degrees of flooding and floating. Waterborne coatings that do not exhibit flooding or floating may show these conditions when diluted. Using dispersants or thickeners with hydrophobic constituents, increasing viscosity, reducing surface tension, etc., all help to prevent or reduce flooding and floating. Comparison tests revealed little influence of processing conditions on flooding or floating. DOI : 10.1007/s11998-004-0014-2 En ligne : https://link.springer.com/article/10.1007/s11998-004-0014-2 Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=3901 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
000587	-	Périodique	Bibliothèque principale	Documentaires	Disponible

---

1 (1 - 2 / 2)