Dispersive mixing performance evaluation of special rotor segments in an intermeshing co-rotating twin-screw extruder by using weighted probability distributions / S. Yamada in INTERNATIONAL POLYMER PROCESSING, Vol. XXX, N° 4 (08/2015)  

[article]  inINTERNATIONAL POLYMER PROCESSING > Vol. XXX, N° 4 (08/2015) . - p. 451-459 Titre : Dispersive mixing performance evaluation of special rotor segments in an intermeshing co-rotating twin-screw extruder by using weighted probability distributions Type de document : texte imprimé Auteurs : S. Yamada, Auteur ; K. Fukutani, Auteur ; K. Yamaguchi, Auteur ; H. Funahashi, Auteur ; K. Ebata, Auteur ; Hideyuki Uematsu, Auteur ; S. Tanoue, Auteur Année de publication : 2015 Article en page(s) : p. 451-459 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Alliages polymères Analyse numérique Calcul Distribution de temps de séjour Extrudeuse bi-vis Extrudeuse rotative Matières plastiques -- Extrusion Index. décimale : 668.4 Plastiques, vinyles Résumé : An intermeshing co-rotating twin-screw extruder is widely used for producing polymer composites. In order to satisfy properties of the composites, it is important to understand mixing performance of segments. In this study, we discussed mixing performance of special rotor segments commercially named VCMT (various clearance mixing technology) by using a numerical analysis method. The several tip clearances of VCMT work for achievement of both self-cleaning and effective mixing. We adopted a particle tracking method to obtain the following two evaluation indices; 1) residence time for the evaluation of its uniformity and 2) maximum 1st principal stress for the evaluation of dispersive mixing. And we evaluated mixing performance of VCMT by using probability distributions of each index. Moreover, we proposed weighted probability distributions as theoretically better evaluation. The probability distributions of VCMT were compared with those of two kinds of kneading disk segments (KDs). From the comparison, it was found that the probability of VCMT in large 1st principal stress region is higher than those of KDs. As a conclusion, VCMT has better mixing performance than KDs for the geometries and operating conditions that were investigated. Note de contenu : - ANALYSIS METHOD AND CONDITIONS : Fundamental equations and properties - Analysis conditions - Particle tracking method - Mixing evaluation indices - PREPARATION FOR NUMERICAL ANALYSIS-DETERMINATION OF COMPUTATIONAL MODEL - RESULTS AND DISCUSSION : Characteristics of residence time distribution - Dispersive mixing performance DOI : 10.3139/217.2972 En ligne : https://drive.google.com/file/d/1XgEHKyQAVgA3w-I0u05dph3hj0nadr47/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=24854 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
17359	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Partially filled flow simulation using meshfree method for high viscosity fluid in plastic mixer / Kazuhide Sekiyama in INTERNATIONAL POLYMER PROCESSING, Vol. XXXIV, N° 2 (05/2019)  

[article]  inINTERNATIONAL POLYMER PROCESSING > Vol. XXXIV, N° 2 (05/2019) . - p. 279-289 Titre : Partially filled flow simulation using meshfree method for high viscosity fluid in plastic mixer Type de document : texte imprimé Auteurs : Kazuhide Sekiyama, Auteur ; S. Yamada, Auteur ; Takaharu Nakagawa, Auteur ; Yasuharu Nakayama, Auteur ; T. Kajiwara, Auteur Année de publication : 2019 Article en page(s) : p. 279-289 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Etat fondu (matériaux) Fluides, Mécanique des Galerkin, Méthode de En mathématiques, dans le domaine de l'analyse numérique, les méthodes de Galerkine sont une classe de méthodes permettant de transformer un problème continu (par exemple une équation différentielle) en un problème discret. Cette approche est attribuée aux ingénieurs russes Ivan Boubnov (1911) et Boris Galerkine (1913). Malaxeurs et mélangeurs Rhéologie Simulation par ordinateur Index. décimale : 668.4 Plastiques, vinyles Résumé : A novel simulation technique for the flow in plastic mixers based on Element-free Galerkin Method (EFGM) has been developed in this study. To improve the simulation accuracy, a “rearrangement” scheme has been employed which eliminates errors caused by the irregular distribution of data points. Through several numerical tests, the new simulation technique has been validated to be applicable to high viscosity fluid flow with enough accuracy. Furthermore, simulation examples for realistic mixers were carried out using the developed technique. From the results, it was found that the developed technique is capable to investigate the relationship between flow behavior inside realistic mixers and operating conditions. Note de contenu : - SIMULATION METHOD : Governing equation - Approximation of velocity field based on MLS interpolation - Discretization - Integration method - Time marching method - New "rearrangement" scheme for improving calculation accuracy - VALIDATION OF DEVELOPED METHOD : Comparison with experiment on rotating cylinder - Comparison with experiment on triangular-shaped rotor - RESULTS AND DISCUSSION OF FLOW SIMULATION INSIDE REALISTIC MIXERS : Numerical simulation condition - Results and discussion DOI : 10.3139/217.3727 En ligne : https://www.degruyter.com/document/doi/10.3139/217.3727/pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=32404 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
20883	-	Périodique	Bibliothèque principale	Documentaires	Disponible

---

1 (1 - 2 / 2)