Dépouillements

Modelling the spreading of screen ink on non-porous substrates / J. M. Bradley in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 231-236 Titre : Modelling the spreading of screen ink on non-porous substrates Type de document : texte imprimé Auteurs : J. M. Bradley, Auteur ; A. Manning, Auteur Année de publication : 2005 Article en page(s) : p. 231-236 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Encre Energie de surface Modélisation des dépôts liquides Revêtements organiques Sérigraphie Index. décimale : 667.9 Revêtements et enduits Résumé : The reduction of dot gain in half-tone printing is desirable in order to accurately reproduce designs in printed format. An important contribution to dot gain is the spreading of ink on the substrate after image formation but prior to immobilisation by curing or drying. The spreading of a typical screen ink was modelled to determine the thermodynamic processes controlling the rate of drop spreading and the timescales over which they are significant. Suggestions are offered as to the characteristics desirable in polymer substrates in order to minimise dot spreading. Note de contenu : - EXPERIMENTAL : Samples - Surface tension and surface energy measurements - Contact-angle measurement - Bulk viscosity - Modelling and error estimation - RESULTS AND DISCUSSION : Variation in surface tension - Correlations in the dynamic spreading parameters - Implications for the control of dot gain - Table 1 : Bulk viscosity of Uvispeed k at the temperature of contact angle relaxation measurements - Table 2 : Surface energy and compopnents of the polymer substrates as supplied - Table 3 : Fitted parameters for the dynamic spreading of Uvispeed k DOI : 10.1007/BF02699577 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699577.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5400 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Preparation and surface characterisation of novel epoxy-based organic-inorganic nano-composite coatings / M. Å pírková in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 237-242 Titre : Preparation and surface characterisation of novel epoxy-based organic-inorganic nano-composite coatings Type de document : texte imprimé Auteurs : M. Å pírková, Auteur ; J. Kotek, Auteur ; M. Å louf, Auteur ; J. Baldrian, Auteur ; J. Brus, Auteur Année de publication : 2005 Article en page(s) : p. 237-242 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Angle de contact Caractérisation Colloides Epoxydes Microscopie à rayons X Montmorillonite Résonance magnétique nucléaire Revêtements Silice La silice est la forme naturelle du dioxyde de silicium (SiO2) qui entre dans la composition de nombreux minéraux. La silice existe à l'état libre sous différentes formes cristallines ou amorphes et à l'état combiné dans les silicates, les groupes SiO2 étant alors liés à d'autres atomes (Al : Aluminium, Fe : Fer, Mg : Magnésium, Ca : Calcium, Na : Sodium, K : Potassium...). Les silicates sont les constituants principaux du manteau et de l'écorce terrestre. La silice libre est également très abondante dans la nature, sous forme de quartz, de calcédoine et de terre de diatomée. La silice représente 60,6 % de la masse de la croûte terrestre continentale. Sol-gel, Procédé Index. décimale : 667.9 Revêtements et enduits Résumé : Hybrid organic-inorganic coatings were prepared by a combination of the polyaddition reactions used for the synthesis of the organic polymeric matrix and by the sol-gel process for the in situ formation of inorganic structures. Two admixtures, differing in size and shape (montmorillonite and colloidal silica), were added to the reaction system. Surface, mechanical and other properties of the resultant products are discussed with respect to the composition and the technique of preparation. Note de contenu : - EXPERIMENTAL : Materials and technique of preparation - Methods of characterisation - RESULTS AND DISCUSSION : Surface characterisation - NMR spectroscopy - Wide-angle x-ray scattering (WAXS) - Transmission electron microscopy (TEM) - Table 1 : Conditions for coating preparation - Table 2 : Tensile characteristics and WAXS periodicity of free-standing films DOI : 10.1007/BF02699578 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699578.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5401 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Perfluoropolyether-based organic-inorganic hybrid coatings: Preparation and surface characterisation / M. Messori in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 243-249 Titre : Perfluoropolyether-based organic-inorganic hybrid coatings: Preparation and surface characterisation Type de document : texte imprimé Auteurs : M. Messori, Auteur ; C. Tonelli, Auteur ; S. Nannarone, Auteur ; M. Montecchi, Auteur ; L. Pasquali, Auteur ; P. Fabbri, Auteur ; Francesco Pilati, Auteur ; Maurizio Toselli, Auteur Année de publication : 2005 Article en page(s) : p. 243-249 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Angle de contact Caractérisation Hydrophobie Matériaux hybrides Oléophobie Perfluoropolyéther Poly-e-caprolactone Sol-gel, Procédé Spectroscopie de photoélectrons Index. décimale : 667.9 Revêtements et enduits Résumé : Hydrophobic-oleophobic coatings were prepared by using the sol-gel process with organic-inorganic hybrids based on perfluoropolyether-polycaprolactone (PFPE-PCL) copolymers. Hybrid coatings were prepared by changing the organic-inorganic ratio, the PFPE/PCL ratio in the copolymer, and the reaction conditions. A complete surface characterisation was carried out by contact angle analysis and x-ray photoemission spectroscopy (XPS). In all cases the wettability of the coatings was found to be very low. Surface composition analysis showed that the surface segregation of the fluorinated PFPE segments was always high enough to give a very high hydrophobic character to the coating surface. Note de contenu : - EXPERIMENTAL : Materials - Prepration of a,w-hydroxyterminated PCL-PFPE-PCL block copolymers - Preparation of a,w-triethoxysilane-terminated PCL-PFPE-PCL block copolymers - Preparation of PCL-PFPE-PCL/silica hybrids - CHARACTERISATION - RESULTS AND DISCUSSION : Surface characterisation DOI : 10.1007/BF02699579 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699579.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5402 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Suspension structures and film morphologies of high-solids acrylic-alkyd hybrid binders / M. J. Deriss in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 251-256 Titre : Suspension structures and film morphologies of high-solids acrylic-alkyd hybrid binders Type de document : texte imprimé Auteurs : M. J. Deriss, Auteur ; O. J. Karlsson, Auteur Année de publication : 2005 Article en page(s) : p. 251-256 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Copolymère alkyde acrylique Dispersions et suspensions Haut extrait sec Latex Liants en phase aqueuse Matériaux hybrides Revêtements organiques Index. décimale : 667.9 Revêtements et enduits Résumé : The development of new binders used for coatings has traditionally been driven by a combination of the need for technical improvements and increased environmental awareness, together with stricter legislation regarding VOC (volatile organic compound) emissions. One interesting way to achieve new types of binders is to combine already existing ones, thereby exploiting the positive properties of both. In the present study, a combination of an alkyd and an acrylic dispersion was used to produce a potential hybrid binder. The structures of the binders both in the liquid state and in films prepared from the hybrids were studied using several microscopy techniques. It was found that the preparation method of the hybrids affected the morphology to a large extent, and the structural information was also linked to the rheological behaviour of the hybrids as well as to the mechanical properties of the final binder films. Note de contenu : - EXPERIMENTAL : Hybrid preparation - Hybrid film preparation - Analysis methods - RESULTS AND DISCUSSION : Hybrid liquid structures - Alkyd droplet size - Film morphologies - Paint properties - Table 1 : Properties, advantages and disadvantages of alkyd emulsions and acrylic polymers as binders in coatings - Table 2 : Abbreviations and descriptions of the samples DOI : 10.1007/BF02699580 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699580.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5403 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Wet chemical deposition of multifunctional conducting coatings made with a nanocomposite suspension / N. Al-Dahoudi in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 257-261 Titre : Wet chemical deposition of multifunctional conducting coatings made with a nanocomposite suspension Type de document : texte imprimé Auteurs : N. Al-Dahoudi, Auteur ; M. A. Aegerter, Auteur Année de publication : 2005 Article en page(s) : p. 257-261 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Blindage (rayonnements) Conducteurs organiques Etain Formulation (Génie chimique) Nanoparticules Oxyde d'indium L'oxyde d'indium(III) (In2O3) est un composé chimique, un oxyde amphotère d'indium. (Wikipedia) Rayonnement infrarouge Sol-gel, Procédé Index. décimale : 667.9 Revêtements et enduits Résumé : A nanocomposite suspension made of redispersable crystalline In2O3·Sn (ITO) nanoparticles and a hybrid organic-inorganic additive was prepared to obtain single 600nm-thick, transparent, electrically-conducting layers. The rheology of the suspension was adjusted so that the formulations could be used to coat different glass and polymer substrates and foils using wet chemical deposition techniques such as spin coating, dip coating, spray coating and web coating. The optical properties (transmission, reflection, absorption) showed that the layers transmitted more than 87% in the visible range, acted as infrared (IR)-shielding coatings for (λ>1.5µm, and effectively reduced the intensity of solar light (Air Mass (AM) 1.5 Global solar spectrum). At the same time, the layers acted as UV blockers for wavelengths less than 400nm, protecting the polymer substrates and foils from degradation when exposed to UV irradiation. The layers exhibited a high conductivity (σ- 1100Sm−1) which made them useful for electrostatic and antistatic purposes as well as for devices that require a transparent conducting coating with sheet resistance higher than a few kΩp[. Furthermore, the layers showed excellent adhesion on all substrates and high resistance against abrasion and weathering degradation, results that are quite promising with respect to their outdoor use. Note de contenu : - Experimental set-up - Coatings characterisation : Optical properties - Mechanical properties - Electrical properties - RESULTS AND DISCUSSION : Sol characterisation - Coating characterisation - Electrical properties - Mechanical properties - Table 1 : Changes of the electrical sheet resistance and transmission at 550nm of MPTS/ITO coatings deposited on various polymer substrates after abrasion, adhesion and humidity tests DOI : 10.1007/BF02699581 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699581.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5404 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Stages of colour alterations during formation of pigmented polymer coatings / Irena. J. Zvonkina in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 263-267 Titre : Stages of colour alterations during formation of pigmented polymer coatings Type de document : texte imprimé Auteurs : Irena. J. Zvonkina, Auteur ; James Thomas Guthrie, Auteur Année de publication : 2005 Article en page(s) : p. 263-267 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Décoloration Formation de film Pigments Polymères en émulsion Revêtements organiques Index. décimale : 667.9 Revêtements et enduits Résumé : The formation of pigmented polymer coatings involves physical and chemical processes that result in changes in the structure and colour of coatings. The main trends and the stages of colour alterations, during the formation of solid coatings from pigmented water-borne polymer dispersed materials at 20°C, are discussed. The stages of colour alteration during coating formation correspond with the periods of weight loss by the coating. Note de contenu : - EXPERIMENTAL : Materials - Methods of preparation - Methods of characterisation - RESULTS AND DISCUSSION : Colour alterations of coatings - Correspondence of the stages of colour change and qeight loss DOI : 10.1007/BF02699582 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699582.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5405 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Oxidative drying of alkyd paints catalysed by a dinuclear manganese complex (MnMeTACN) / Z. O. Oyman in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 269-275 Titre : Oxidative drying of alkyd paints catalysed by a dinuclear manganese complex (MnMeTACN) Type de document : texte imprimé Auteurs : Z. O. Oyman, Auteur ; J. H. Bieleman, Auteur ; A. Schut, Auteur ; J. Ter Borg, Auteur ; R. van der Linde, Auteur ; W. Ming, Auteur Année de publication : 2005 Article en page(s) : p. 269-275 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Catalyseurs métalliques Complexes métalliques Manganèse Microscopie confocale Raman Polyalkydes Polymérisation par oxydation Revêtements en phase aqueuse Revêtements organiques Index. décimale : 667.9 Revêtements et enduits Résumé : The application of a dinuclear manganese complex (MnMeTACN) as a catalyst in the oxidative drying of alkyd coatings is described. Experimental results on the film properties (drying time and film hardness) for various solvent- and water-borne alkyd coatings demonstrate that MnMeTACN is a potential alternative for commercially-available Co- and Mn-based catalysts. MnMeTACN appears to be suitable for both water-borne and solvent-borne alkyd systems. Confocal Raman microscopy is used to study the depth profile of the drying of alkyd coatings catalysed by different catalysts, and it has been found that slow surface drying is somewhat compensated by relatively fast deep layer drying. Note de contenu : - EXPERIMENTAL : Materials - Sample preparation - Confocal Raman microscopy - Drying tests of alkyd resin-based paints - RESULTS AND DISCUSSIONS : Effect of various catalysts on the drying of alkyd resins followed by CRM - Depth profiling during the drying of solvent-borne alkyd resins - Depth profiling during the drying of water-borne alkyd resins - Implications from surface versus deep-layer drying - Drying tests and film properties of alkyd coatings - Table 1 : Drying tesls and lilm properties of a solvent-borne shorl-oil alkyd resinbased paint (URALAC AK 429 WX 55) - Table 2 : Drying tesls and lilm properties of a solvent-borne long-oil alkyd resinbased paint (SETAL 16 LV WS-70) - Table 3 : Drying tesls and lilm properties of a short-oil alkyd emulsion-based paint (URADIL AZ 554 Z 50) - Table 4 : Drying tests and lilm properties of a long-oil alkyd emulsion-based paint (URADIL AZ 516 Z-60) DOI : 10.1007/BF02699583 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699583.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5406 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Use of a fatty acid oxazoline derivative as a reactive diluent / Y. Berry-Walker in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 277-280 Titre : Use of a fatty acid oxazoline derivative as a reactive diluent Type de document : texte imprimé Auteurs : Y. Berry-Walker, Auteur ; David L. Trumbo, Auteur ; A. C. Scheets, Auteur Année de publication : 2005 Article en page(s) : p. 277-280 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Acides gras Diluants Formulation (Génie chimique) Oxazoline Polyalkydes Polymérisation par oxydation Revêtements organiques Index. décimale : 667.9 Revêtements et enduits Résumé : Oxazoline derivatives of the mixture of fatty acids found in tall oil were used as a reactive diluent for two types of alkyd polymers. The polymers had relatively good solubility in the oxazoline and solutions with moderate viscosity were obtained. Films made from the polymer solutions showed little property development at ambient temperatures even after several days. However, films cured at elevated temperatures had good properties in terms of solvent resistance, hardness and gloss. The degree of property development depended on the length of time the films remained at an elevated temperature. Note de contenu : - Table 1 : Polymer characterisation and solution viscosity results - Table 2 : Film properties - Table 3 : Film properties of methyl ethyl ketone solvent formulations DOI : 10.1007/BF02699584 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699584.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5407 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Water-repellent coating for mobile phone microphones / G. Yamauchi in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 281-283 Titre : Water-repellent coating for mobile phone microphones Type de document : texte imprimé Auteurs : G. Yamauchi, Auteur ; N. Funakoshi, Auteur ; T. Shimizu, Auteur ; Y. Yasuno, Auteur ; Y. Riko, Auteur Année de publication : 2005 Article en page(s) : p. 281-283 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Dioxyde de titane Imperméabilisation Liants Nanoparticules Perfluoropolyéther Photocatalyse Polyfluorure de vinylidène Polytétrafluoréthylène Revêtements organiques Index. décimale : 667.9 Revêtements et enduits Résumé : A water-repellent coating material has been developed which is composed of low molecular-weight poly(tetrafluoroethylene) (PTFE) particles and anatase-type photocatalytic TiO2 nano particles, fluoro-oil (perfluorinated polyether) and a polyvinylidene fluoride binder. The presence of these PTFE particles in the coating material makes it possible for the water-repellency properties of this material to be improved by achieving a water contact angle of more than 150�. The photocatalytic activity of the TiO2 particles incorporated in the water-repellent coating inhibits the surface contamination which previously had caused the deterioration of the water-repellent properties. This water-repellent coating can be applied to mobile phone microphones. The water repellency of the electret condenser microphone improves the durability of the mobile phone. Note de contenu : - INTRODUCTION : Material preparation - WATER-REPELLENT PROPERTY - APPLICATION TO MOBILE PHONE MICROPHONES : Basic structure of ECM - Acoustic characteristics DOI : 10.1007/BF02699585 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699585.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5408 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Advances in the science and technology of paints, inks and related coatings : 2005 / I. Holme in SURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS, Vol. 88, B4 (12/2005)  

[article]  inSURFACE COATINGS INTERNATIONAL. PART B : COATINGS TRANSACTIONS > Vol. 88, B4 (12/2005) . - p. 285-299 Titre : Advances in the science and technology of paints, inks and related coatings : 2005 Type de document : texte imprimé Auteurs : I. Holme, Auteur Année de publication : 2005 Article en page(s) : p. 285-299 Note générale : Bibliogr. Langues : Anglais (eng) Catégories : Adhésion Antimicrobiens Bois Catalyseurs Composés organiques volatils Conducteurs organiques Corrosion Formation de film Impression jet d'encre Matériaux cimentaires Matériaux hybrides Photoréticulation Résistance aux conditions climatiques Revêtements -- Séchage sous rayonnement ultraviolet Revêtements organiques Rhéologie Index. décimale : 667.9 Revêtements et enduits Résumé : This review summarises the developments in adhesion, VOC emissions, coatings, transparent conductive coatings, hybrid organic-inorganic coatings, UV curing, biocidal coatings, paints, weathering, wood coatings, surface treatment of concrete, metal corrosion, pigments, film formation, printing, modelling fluid flow in printing, dot gain and inkjet printing reported in Surface Coatings International Part B: Coatings Transactions, 88, 2005. Note de contenu : - Adhesion - Approaches to decreasing VOC emissions in paints and coatings - Catalysts for drying of alkyd paints and coatings - Phenolic epoxidised polyurethane coatings - Epoxy resin coatings - Direct fluorination of polyethylenes - Hyperbranched polymers - Water-repellent coating to prevent surface contamination - Transparent conductive coatings - Lower critical solution temperature (LCST) polymer coating - Ultrasonic atomisation of ink - Polymeric antioxidants for paints - Paint film formation determined by diffusing wave spectroscopy - Hybrid organic-inorganic coatings - UV curing by radical and cationic photoinitiation - Network non-isocyanate polyurethane coatings - Biocidal coatings - Modelling the weathering of coatings - Wood coatings - Surface treatment of concrete - Metal corrosion - Pigments - Film formation in pigmented polymer coatings - Modelling fluid flow in printing - Dot gain in printing - Inkjet printing DOI : 10.1007/BF02699586 En ligne : https://link.springer.com/content/pdf/10.1007/BF02699586.pdf Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=5409 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
003404	-	Périodique	Bibliothèque principale	Documentaires	Disponible