Improved spinnability of metallocene polyethylenes by using processing aids / R. Vogel in INTERNATIONAL POLYMER PROCESSING, Vol. XVIII, N° 1 (03/2003)  

[article]  inINTERNATIONAL POLYMER PROCESSING > Vol. XVIII, N° 1 (03/2003) . - p. 67-73 Titre : Improved spinnability of metallocene polyethylenes by using processing aids Type de document : texte imprimé Auteurs : R. Vogel, Auteur ; Savvas G. Hatzikiriakos, Auteur ; Harald Brünig, Auteur ; B. Tändler, Auteur ; M. Golzar, Auteur Année de publication : 2003 Article en page(s) : p. 67-73 Note générale : Bibliogr. Langues : Anglais (eng) Index. décimale : 668.9 Polymères Résumé : Melt spinning is a polymer processing technique that is strongly influenced by the extensional flow behaviour of polymer melts. Therefore only a few polymeric materials are usable for this kind of processing with sufficient take-up speeds. When approaching critical conditions of deformation most polymers show either fibre break in the molten state either by a brittle cohesive rupture or a ductile failure. During the melt spinning of pure and modified metallocene poylethylenes additional flow instabilities occur within the spinning die. Namely, wall slip, 'sharkskin' and pressure oscillations (gross fracture) may be obtained dependending on the volume flow rate. Pressure oscillations lead to diameter oscillations of the melt extrudate, which create local increase of tensile stress in the spin line. This effect immediately causes fiber break in the spinline. Therefore, melt spinning of polyethylenes was only possible up to a critical molecular weight or its relating melt viscosity. The limitation of the molecular weight restricts the mechanical properties of the melt spun fibres. This paper reports on an attempt to find out appropriate processing aids for suppressing 'sharkskin' effects and pressure oscillations in an attempt to overcome the limitation of a critical molecular weight. At first, the critical conditions for the onset of flow instabilities for higher molecular weight polymers were analysed. Further experiments concerned with the use of processing aids for melt spinning of metallocene polyethylenes of higher molecular weights. A combination of boron nitride powder and a fluoroelastomer was found to be an effective processing aid for this process. DOI : 10.3139/217.1722 En ligne : https://drive.google.com/file/d/1QKKoX0SBuwLGtIqeg0yo6MePu06Ntr77/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=15851 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
001023	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Melt spinning of reactive extruded and/or blended polymer fibers by means of an online coupled twin screw extruder / R. Beyreuther in INTERNATIONAL POLYMER PROCESSING, Vol. XVIII, N° 1 (03/2003)  

[article]  inINTERNATIONAL POLYMER PROCESSING > Vol. XVIII, N° 1 (03/2003) . - p. 74-79 Titre : Melt spinning of reactive extruded and/or blended polymer fibers by means of an online coupled twin screw extruder Type de document : texte imprimé Auteurs : R. Beyreuther, Auteur ; B. Tändler, Auteur ; R. Vogel, Auteur ; M. Hoffmann, Auteur Année de publication : 2003 Article en page(s) : p. 74-79 Note générale : Bibliogr. Langues : Anglais (eng) Index. décimale : 668.9 Polymères Résumé : After some general introductory remarks to the advantageous application of a twin screw extrusion to the melt spinning the lecture deals with investigations of elastomeric fibers consisting of ethylene-octene-copolymers which have been grafted by organosilanes and additionally blended with polybutylenterephthalates (PBT) and/or polyesterelastomers (PEE), all by means of a reactive twin screw extruder coupled with a side feeding single screw extruder in an online melt spinning process. It will be demonstrated that considerably improved mechanical properties of the elastomeric EO-fibers can be reached with this additional blend step. All spun fiber samples will be characterized regarding their structural and mechanical properties extensively. This work is a decisive expansion of our results published during the last two years regarding to the twin screw extrusion melt spinning [1 to 4]. DOI : 10.3139/217.1724 En ligne : https://drive.google.com/file/d/1YnVPOkI0SChNOG7SPdfcTMJL9WmP2r1J/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=15852 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
001023	-	Périodique	Bibliothèque principale	Documentaires	Disponible

A new method to determine the filament force tension within the fibre formation zone / Harald Brünig in INTERNATIONAL POLYMER PROCESSING, Vol. XVIII, N° 1 (03/2003)  

[article]  inINTERNATIONAL POLYMER PROCESSING > Vol. XVIII, N° 1 (03/2003) . - p. 41-45 Titre : A new method to determine the filament force tension within the fibre formation zone Type de document : texte imprimé Auteurs : Harald Brünig, Auteur ; B. Tändler, Auteur Année de publication : 2003 Article en page(s) : p. 41-45 Note générale : Bibliogr. Langues : Anglais (eng) Index. décimale : 668.9 Polymères Résumé : A non-contact method to determine the force tension of the spinning line is proposed by a non-vertical arrangement of the melt spinning equipment. The curvature of the spinline caused by gravitation was determined experimentally by measuring the spinline location. This is the key for the calculation of the filament force only by geometric measurements. DOI : 10.3139/217.1715 En ligne : https://drive.google.com/file/d/1qWGTromA4pXKk747Sljpdw1hhmCc6gaW/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=15849 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
001023	-	Périodique	Bibliothèque principale	Documentaires	Disponible

Rheological and theoretical estimation of the spinnability of polyolefines / R. Vogel in INTERNATIONAL POLYMER PROCESSING, Vol. XIV, N° 1 (03/1999)  

[article]  inINTERNATIONAL POLYMER PROCESSING > Vol. XIV, N° 1 (03/1999) . - p. 69-74 Titre : Rheological and theoretical estimation of the spinnability of polyolefines : Part I : Rheological study Type de document : texte imprimé Auteurs : R. Vogel, Auteur ; Harald Brünig, Auteur ; R. Beyreuther, Auteur ; B. Tändler, Auteur ; D. Voigt, Auteur Année de publication : 1999 Article en page(s) : p. 69-74 Note générale : Bibliogr. Langues : Anglais (eng) Index. décimale : 668.9 Polymères Résumé : Fibers and films - Melt spinning is a polymer processing technique that makes great demands on the extensibility of the polymer melt in the distance between die exit and solidification point [1]. The polymer material is exposed to a rapidly growing deformation rate over a large range of deformation within a short time of about 100 milliseconds. Simultaneously an extreme cooling occurs with cooling rates of about 1000 K/s. For this reason only a few polymer materials are usable for this kind of polymer processing with sufficient take-up speeds. Most polymers show afiber break in the motten state either by brittle cohesive rupture or ductile failure when approaching critical conditions of deformation. The rheological behaviour of a polymer melt at the critical conditions of deformation in the fiber forming process can not be predicted by means of usual rheological material functions. This paper reports the attempt to find out material functions, which describe the critical deformation states of the melt spinning process. The established material functions are compared with the results of spinning experiments to estimate their practicality. DOI : 10.3139/217.1518 En ligne : https://drive.google.com/file/d/1NHp5HYl1M0Ym8rPxPuT4r80dARmOnGr-/view?usp=drive [...] Format de la ressource électronique : Pdf Permalink : https://e-campus.itech.fr/pmb/opac_css/index.php?lvl=notice_display&id=16114 [article]

Réservation

Réserver ce document

Exemplaires (1)

Code-barres	Cote	Support	Localisation	Section	Disponibilité
001007	-	Périodique	Bibliothèque principale	Documentaires	Disponible

---

1 (1 - 4 / 4)